Parts for Kitchenaid KUDT03FTBL2: 03 - Door And Latch Parts

Removes residue, odor-causing soils, and food particles from dishwasher tub and gasket. Use monthly to eliminate unwanted odors and maintain peak performance.

Fixes loose panels, rattling doors, or wobbly components caused by stripped or missing screws. Secures brackets, covers, and mounting hardware. Easy DIY.

This factory-specified screw secures panels, brackets, and internal components in your appliance. Replacing worn or missing hardware restores a tight fit to help reduce vibration, noise, and premature wear.

• Fastens sheet metal, brackets, or plastic parts as designed by the manufacturer
• Helps maintain alignment and reduce vibration/rattling
• Direct replacement for stripped, corroded, or missing screws
• Common signs: loose panels or trim, shifting components, screw won't tighten

• Disconnect power; shut off water or gas supply if applicable
• Use the correct driver to avoid stripping the head
• Start threads by hand to prevent cross-threading; tighten snugly without overtightening
• Replace one-for-one in the original location per service information

The Air Inlet is an OEM part for Whirlpool dishwashers. It draws in ambient room air to assist in drying dishes after wash cycles have been completed. With openings around its base, the air inlet facilitates airflow through the dish rack to evaporate residual moisture left on rinsed dishes.

Causes of a bad air inlet can include cracks in the plastic preventing proper draw of air currents, or obstructions blocking air pathways.

Symptoms of a bad air inlet include:

• Dishes remaining wet and not fully dried after cycles
• Puddles or watermarks left behind on upper racks and dishes
• Slow air movement detected near the bottom air vents
• Musty odors or smells developing inside the dishwasher

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

Also order air vent gasket

Seals the dishwasher air vent to prevent water leaks during operation. Replace if you notice dripping under the vent or wet insulation behind the panel.

Directs airflow in your dishwasher's vent system. Replace if cracked, discolored, or blocking proper ventilation. Confirm fit with your model number.

Dispenser won't latch or close? This detergent dispenser releases soap at the right time. Moderate DIY repair requiring inner door panel removal.

Removes residue, odor-causing soils, and food particles from dishwasher tub and gasket. Use monthly to eliminate unwanted odors and maintain peak performance.

Covers and seals the rinse aid compartment to prevent leaks and ensure proper dispensing. Replace if damaged, melted, or missing. Verify fit with your model.

This wire harness routes power and signals between the oven's controls and internal components to restore proper electrical connections and reliable operation. It replaces damaged, frayed, or corroded wiring that can cause intermittent function. What it does:

• Provides the factory routing and connector interfaces between control modules and internal oven components
• Restores lost or intermittent electrical connections that can cause nonresponsive controls or heating issues
• Replaces damaged insulation, broken wires, or melted connectors to reduce short and fire risk
• Maintains correct connector fit and secure wiring routing for reliable oven performance

• One complete wire harness as shown

• Disconnect all power to the appliance before beginning work to avoid electrical shock
• Handle connectors by the plug bodies; do not pull on wires when removing or seating connectors
• Route and secure the harness along factory clips and channels; avoid contact with heating elements or sharp edges
• Inspect connector terminals and mating components; replace or repair any additional damaged parts before reassembly

The Hex-Head Screw is an OEM replacement part for use in Whirlpool dishwashers. This metal screw measures approximately ¾ inch long. Its primary purpose is to secure the dispenser bracket in place, ensuring stable operation. This hex-head screw is designed for use with compatible hexagonal tools. This makes installation and removal straightforward. This part is sold individually and is guaranteed to fit your dishwasher door panel. This screw is compatible with select Whirlpool brand models including Amana, Crosley, Estate, Inglis, Jenn Air, Kenmore, Kitchen Aid, and Maytag.

Dishwasher door seal prevents water leaks between the console and door. Replace if you notice leaking during cycles or visible wear. Confirm fit with model.

If your detergent dispenser is loose or falling off, this bracket secures it to the door panel. Moderate DIY repair requiring door disassembly.

Fix a broken or missing dishwasher detergent dispenser cover. This shield protects the dispenser assembly and restores a finished look to your unit.

Removes residue, odor-causing soils, and food particles from dishwasher tub and gasket. Use monthly to eliminate unwanted odors and maintain peak performance.