General Electric Dryer Plug Or Insert

A replacement reversible plug door that covers and protects the appliance power inlet while letting the cord exit left or right for tidy cord routing. Restores a clean back panel appearance and helps keep the power connection protected from debris. What it does:

• Covers the power inlet opening to protect the plug and inlet from dust and debris.
• Reversible design lets you route the power cord to either side to fit against the wall.
• Helps keep the cord tucked close to the appliance so the unit can sit flush with cabinetry or walls.
• Replace when the door is cracked, broken, missing, or no longer holds the plug securely.

• Always unplug the appliance before starting any repair or inspection.
• May require access to the rear panel; check your owner's manual for disassembly steps.
• Check orientation before finalizing installation to ensure correct left/right cord routing.

This plug button is a replacement cosmetic/functional cap that covers an unused control opening or receptacle on the appliance, restoring a finished appearance and helping keep out dust and debris. What it does:

• Covers and seals an unused control hole or plug location to improve appearance
• Helps prevent dust, lint, and small debris from entering the opening
• Restores a flush, finished look when a switch, knob, or connector is missing
• Simple snap-in design for a clean, low-profile result

• Disconnect power to the appliance before servicing.
• Typically snaps into place; no special tools required for most installations.
• If removal is needed, use a plastic pry tool to avoid scratching surrounding surfaces.
• Your appliance owner's manual or parts diagram to correct placement.

This reversible door plug covers the unused hinge or mounting hole after changing a door swing, restoring a clean appearance and helping keep out dirt and drafts. Simple, color-matched replacement for a neat finish. What it does:

• Covers exposed hinge or mounting holes on the door edge for a finished look
• Helps block dust, pests and drafts from entering through unused openings
• Matches original geometry to sit flush with the door surface
• Designed to work with reversible door installations where a hole is no longer used

• One (1) reversible door plug

• No tools are typically required; press plug into the unused hole until it seats securely
• Confirm correct orientation before installing to ensure a flush fit
• Inspect surrounding sealing surfaces and clean area before installation
• If plug is damaged or does not seat properly, replace with the exact part number

This plastic screw plug covers and protects unused screw holes on appliance panels for a clean, finished look while helping keep out dirt and moisture. Simple replacement to restore appearance and prevent debris buildup. What it does:

• Covers exposed screw holes in trim or panels to improve appearance
• Helps block dust and light debris from entering through openings
• Prevents accidental contact with recessed screws
• Useful when replacing panels or removing components where plugs were lost

• One plastic screw plug

• Disconnect power or unplug the appliance before accessing internal panels when necessary
• Press the plug into the hole by hand; use a flat tool gently if alignment is tight
• Do not force or hammer the plug to avoid panel damage
• Replace any damaged surrounding trim before installing plug for a secure fit

This light hole plug seals the unused drum-light opening in the dryer cabinet. Replacing a missing or brittle plug helps contain lint, limit drafts, and protect internal components around the opening.

• Covers the factory light opening when no drum light is installed
• Helps maintain proper cabinet airflow and lint containment
• Shields the opening from dust and moisture
• Replace if the plug is missing, cracked, hardened, or won't stay seated

• Disconnect power before servicing
• Access the light-hole location per your model's service instructions
• Press the plug fully into the hole until seated flush
• Ensure no wires or components are pinched around the opening

This control console plug is a small replacement wire connector that restores a secure electrical connection at the appliance control console, helping restore reliable console function and user controls. What it does

• Reconnects control console wiring to the console board, maintaining signal and power continuity
• Can resolve intermittent or lost console/display operation caused by a damaged or loose connector
• Provides the OEM-matching fit and terminal alignment for proper mating with the control board
• Useful when the original plug shows corrosion, bent terminals, or broken housing

• One control console plug (wire connector) as shown

• High-level replacement: access the console panel and unplug the old connector before installing the new one
• Disconnect power at the breaker or unplug the appliance before starting any work
• Verify connector orientation and fully seat until it clicks; avoid forcing pins to prevent damage