Electrolux Refrigerator Parts

Side rail that supports and guides your refrigerator's sliding freezer basket. Replace this hanger if cracked, broken, or worn to restore smooth sliding.

This replacement door bin mounts on the inside of your refrigerator door to hold bottles, jars, and condiments. Replacing a cracked or loose bin restores safe, usable storage and helps keep items organized and accessible.

• Provides storage on the door to keep bottles and jars upright
• Restores capacity when the original bin is cracked, warped, or missing
• Helps prevent items from tipping or falling when the door opens/closes
• Common symptoms: bin falls off, won't stay seated, or has broken tabs/cracks

What's included: 1 door bin Install notes:

• Remove all items from the old bin; lift straight up to release from the door slots
• Align the new bin's tabs with the slots and press down until fully seated
• Do not force; re-align if resistance is felt to avoid damaging the door liner
• Place in the correct door position for your model; some bins aren't interchangeable between levels

Replacement glass panel for refrigerator shelves. Restores a smooth surface when original is cracked, broken, or missing. Fits shelf assemblies.

Fastens the auger shaft in your refrigerator's ice maker assembly. Replace if cracked, broken, or missing to secure the auger and prevent rubbing.

Frost buildup or no defrosting? This defrost thermostat monitors evaporator coil temperature to trigger defrost cycles. DIY-friendly repair, 30-45 minutes.

Reduces odors from onions, garlic, fish, and spoiled food using activated carbon and baking soda. Replace every 6 months for fresh air. Confirm fit by model.

Refrigerator not cooling or compressor not running? The inverter control board regulates the variable-speed compressor. Restore normal cooling performance.

Secures the crisper slide rail to the refrigerator liner for smooth drawer operation. Replace if broken or missing to restore proper alignment and support.

Collects water from evaporator defrost cycles. Mounts near compressor under refrigerator. Replace if cracked, leaking, or damaged to prevent odors.

Vertical flipper mullion assembly mounts to fresh-food door and pivots to seal center gap between French doors. Replace if cracked, broken, or rusting.

Freezer won't stay cold or runs too cold? A faulty heat exchanger disrupts refrigerant flow. Requires professional brazing and refrigerant recharge.

The Water Filter Bypass is an OEM replacement part for Frigidaire refrigerators. It provides an alternative water supply route to bypass the refrigerator's built-in water filtration system. The bypass allows refrigerator water and ice dispensers to operate without water flowing through the installed filter cartridge. 

Causes of a malfunctioning bypass can include mineral buildup inhibiting proper operation of the bypass valve, worn seals or O-rings not providing a tight seal or physical damage.  

Symptoms include:

• Inability to bypass the water filter when needed  
• Leaks from the bypass area
• The filter bypass not functioning or engaging properly

This OEM replacement is also compatible with refrigerator brands like Electrolux, Gibson, Kelvinator, and select Kenmore models.

Interior light bulb for freezers and refrigerators. Replace when bulb burns out, flickers, or dims to restore visibility inside your appliance.

This mullion assembly forms the front center divider of the refrigerator and includes an integrated anti-sweat heater. It helps keep the area where the door gaskets meet dry, supporting a clean look and a reliable, moisture-free seal.

• Provides the rigid center divider that the door gaskets seal against
• Built-in heater warms the divider to reduce sweating/condensation in humid conditions
• Helps limit air leaks that can lead to moisture, frost, or temperature fluctuations
• Common signs of trouble: persistent condensation on the center divider, visible cracks/warping, or poor gasket contact along the center

• Disconnect power to the refrigerator before servicing; wear cut-resistant gloves
• Remove mounting fasteners, carefully release the assembly, and disconnect the wire harness (note routing/orientation)
• Position the new assembly, reconnect the harness securely, and reinstall fasteners without overtightening
• Verify doors close smoothly and gaskets contact evenly along the divider before restoring power

This replacement screw secures appliance panels, brackets, and internal components. It restores a tight, rattle-free fit and proper alignment when an original fastener is missing, stripped, or corroded.

• Fastens metal or plastic parts to the cabinet/frame
• Helps maintain alignment and reduce vibration or rattling
• Direct replacement for lost, damaged, or rusted hardware
• Keeps covers and brackets safely in place

• Disconnect power before servicing; for gas appliances, also shut off gas supply
• Match one-for-one with the original screw; verify length/type before installation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver bit to prevent stripping the screw head

Limits how far the refrigerator door swings open. Replace this stop if it's worn, broken, or missing to protect the hinge and prevent door overextension.