Electrolux Refrigerator Parts

Refrigerator clicking but not cooling? A failed compressor starter prevents reliable startup. This part restores proper cooling by helping the compressor start.

This is a small bearing that sits in the upper door hinge of the refrigerator, allowing the door to pivot smoothly when opened and closed. It reduces friction and wear between the hinge pin and the door. Replace this bearing if the refrigerator door squeaks, feels stiff, does not close properly, or if the existing bearing is worn or cracked.

Directs water from the inlet valve to the ice maker fill cup. Replace if cracked, kinked, frozen, or causing leaks inside your freezer compartment.

Left-hand gray upper hinge cover snaps over the top door hinge to conceal hardware and restore a finished look. Replace when cracked, broken, or missing.

Replacement screw that secures brackets, shelves, trim, panels, and covers inside your appliance. Install when the original is missing, stripped, or corroded.

This is a start relay device that attaches to the compressor and provides the initial electrical boost needed to start the compressor motor. It works in conjunction with the run capacitor to get the compressor running and then disengages once the motor reaches operating speed. Replace this device if the refrigerator is not cooling, the compressor clicks on and off repeatedly, or you hear a buzzing sound coming from the back of the unit.

This small permanent magnet is used in supported refrigerator assemblies to actuate a mating reed switch or metal keeper. It helps the appliance recognize a closed position or hold a light cover/door closed for proper operation. What it does:

• Works with a reed switch or ferrous keeper to provide position sensing or magnetic latching
• Helps ensure features dependent on closed position operate correctly
• Can resolve issues where a small cover or door won't stay closed
• Address erratic "door ajar" indications tied to magnetic sensing

• Disconnect power and water before servicing
• Note the original magnet's location and orientation; polarity matters for proper operation
• Seat the magnet fully in its pocket or holder and align with the mating switch/keeper
• Test the related function before reassembling panels and trim

Supports the glass shelf above crisper drawers and forms drawer tracks. Replace this frame if cracked, warped, or broken to restore stable shelving.

Supports the crisper shelf glass and forms the top of humidity drawers. Replace if cracked, warped, or broken from heavy loads or impact.

Powers your refrigerator's interior lighting. Replace when lights dim, flicker, or fail. Confirm fit with your model number before ordering.

The Drawer Glide Gear is an OEM replacement part for Frigidaire refrigerators. It is a metal component located on each side of wire shelf tracks that work together to make shelf and drawer movements smooth. 

Causes of bad glide gears can include wear from years of extended usage, dents or deformation that restrict proper motion, or failure of lubricating parts inside the gear mechanism.

Symptoms of a bad Drawer Glide Gear include:

• Shelves or drawers that stick or fail to slide freely
• Noisy squeaking or grinding noises coming from shelf areas  
• Shelves difficult to properly align or position as needed

As a high-stress moving part, glide gears can degrade and lead to slothful storage access over time. Replace with this genuine OEM component for optimally smooth shelf performance on your Frigidaire refrigerator. The replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This replacement screw secures designated components in your appliance to maintain a tight, rattle-free fit. Replacing missing or stripped hardware restores proper attachment and helps keep panels and trim properly aligned.

• Fastens specified parts to the cabinet or frame
• Helps maintain alignment of panels and trim pieces
• Replaces missing, stripped, or corroded screws
• Common symptoms: loose or vibrating parts, panel/trim won't stay secured, visible missing hardware

• Disconnect power to the appliance before servicing
• Hand-start threads to avoid cross-threading; use the correct driver
• Do not overtighten, especially when threading into plastic
• If replacing multiple screws, replace one at a time to maintain alignment

Small spring that provides return tension for refrigerator actuator lever mechanisms. Replace if spring is broken, stretched, missing, or lost during repair.

Channels defrost water from the evaporator to the rear drain pan. Replace this tube if it's cracked, clogged, missing, or has become brittle over time.

Covers the factory test opening on your refrigerator cabinet or liner. Replace if missing, cracked, or damaged to restore a finished look and seal.

This slide set replaces the right- and left-hand rails that guide and support a drawer or rack. It restores smooth, aligned movement so the assembly opens and closes easily without sticking, wobbling, or jumping off the track.

• Guides and stabilizes the drawer/rack on both sides for smooth travel
• Maintains alignment to reduce binding, uneven movement, and premature wear
• Replaces worn, bent, or broken slides that affect operation
• Common symptoms: sticking, rough/grinding movement, tilt or sag, popping off track, hard to open/close

• Disconnect power; shut off gas/water. Remove the drawer or rack before servicing.
• Note L/R orientation; remove old slides and reuse existing screws/brackets.
• Install new slides in the same positions; ensure they are fully seated and aligned.
• Test movement several times before returning the appliance to service; wear cut-resistant gloves.