Electrolux Refrigerator Parts

Replaces cracked or broken mounting bracket in your freezer. Securely holds internal components in proper alignment. Needed when original is damaged.

This slide set replaces the right- and left-hand rails that guide and support a drawer or rack. It restores smooth, aligned movement so the assembly opens and closes easily without sticking, wobbling, or jumping off the track.

• Guides and stabilizes the drawer/rack on both sides for smooth travel
• Maintains alignment to reduce binding, uneven movement, and premature wear
• Replaces worn, bent, or broken slides that affect operation
• Common symptoms: sticking, rough/grinding movement, tilt or sag, popping off track, hard to open/close

• Disconnect power; shut off gas/water. Remove the drawer or rack before servicing.
• Note L/R orientation; remove old slides and reuse existing screws/brackets.
• Install new slides in the same positions; ensure they are fully seated and aligned.
• Test movement several times before returning the appliance to service; wear cut-resistant gloves.

The Drawer Glide Gear is an OEM replacement part for Frigidaire refrigerators. It is a metal component located on each side of wire shelf tracks that work together to make shelf and drawer movements smooth. 

Causes of bad glide gears can include wear from years of extended usage, dents or deformation that restrict proper motion, or failure of lubricating parts inside the gear mechanism.

Symptoms of a bad Drawer Glide Gear include:

• Shelves or drawers that stick or fail to slide freely
• Noisy squeaking or grinding noises coming from shelf areas  
• Shelves difficult to properly align or position as needed

As a high-stress moving part, glide gears can degrade and lead to slothful storage access over time. Replace with this genuine OEM component for optimally smooth shelf performance on your Frigidaire refrigerator. The replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Machine screw secures panels, brackets, and internal components in washers. Replace missing, rusted, or stripped screws to restore proper fit and alignment.

This Temperature Controller regulates cooling by switching power to the compressor and related circuits to hold the set temperature. Replacing a failing controller restores accurate temperature control and reliable operation. What it does:

• Cycles cooling components to maintain the temperature you set
• Helps keep cabinet temperatures consistent for proper food storage
• Coordinates on/off operation to prevent overcooling or warm conditions
• Common failure symptoms: too warm or too cold, runs constantly or won't start, control/dial unresponsive

• 1 temperature controller

• Disconnect power before servicing—this is a line-voltage control
• Access the control area, label or photograph wire positions, and move wires one at a time to the new controller
• Reuse existing mounting hardware and any knob/overlay as applicable
• After install, set to mid setting and allow up to 24 hours for temperatures to stabilize

Replace your refrigerator's water inlet tube when cracked, split, or leaking. Connects water inlet valve to internal filter or dispenser system.

Support bar for refrigerator freezer drawer assembly. Installs between roller tracks to stabilize drawer and prevent shifting. Replace if broken or missing.

Restores smooth drawer movement in your refrigerator. Replace worn, cracked, or broken slide assembly when drawer sticks, sags, or loses alignment.

Supports and aligns the refrigerator door at the bottom pivot point. Replace if bent, cracked, or worn to restore proper door alignment and movement.

Secures and aligns the vertical door trim between refrigerator doors. Replace if cracked, broken, or worn to restore proper door alignment and seal.

Specs: 1.40`` long

Spacer that fits between refrigerator door hinge components to maintain proper clearance and alignment. Replace if worn, cracked, or missing.

Replacement drive gear for bottom-mount refrigerators. Restores smooth motion transfer between internal components. Order when original is cracked or worn.

Housing that forms the framework for the ice crusher assembly inside your refrigerator's ice bucket. Replace if cracked, broken, or damaged to restore proper support.

Fridge not cooling or making loud buzzing noise? This compressor kit restores cooling in refrigerators and freezers. Professional repair recommended.

Refrigerator won't cool or compressor won't start? This compressor start relay energizes the start winding to restore cooling. DIY-friendly repair.