Electrolux Wall Oven Parts

The Support Roller Washer is an OEM part for Frigidaire dryers, designed to ensure the smooth and stable operation of the dryer drum. Positioned between the support roller and the shaft, this washer plays a critical role in reducing friction and wear, allowing the drum to rotate smoothly and quietly.

Causes of these symptoms often stem from normal wear and tear, which can lead to the degradation of the washer over time.  

Symptoms of a bad Dryer Support Roller Washer include:

• Unusual noises, such as squeaking or grinding, indicating increased friction during drum rotation
• The dryer drum appears to wobble or is misaligned during operation
• Increased vibration of the dryer, which can lead to wear on other components

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This oven control board manages the electronic clock/timer and controls bake and broil functions. Replacing a failed board restores accurate temperature control, display, and keypad responsiveness so your range or wall oven heats and operates reliably again.

• Directs power to bake and broil elements based on user settings and oven sensor feedback
• Common symptoms: oven won't start or won't heat; temperatures are erratic or inaccurate
• Display is blank, dim, frozen, or keypad buttons are unresponsive
• Repeated fault/error codes or beeping from the control; intermittent cycling or shutdown

• Disconnect power at the breaker or fuse box before servicing; verify no voltage is present
• Use anti-static precautions and handle the board by the edges
• Photograph/label wiring; move connectors one at a time to the same locations on the new board; reuse original mounting hardware
• Restore power, set the clock, and run a short bake test to confirm proper operation

This natural gas burner orifice meters gas flow to a specific burner on your range, delivering the correct flame size and heat output. Replace a worn or clogged orifice to restore stable, efficient burner performance. What it does:

• Meters natural gas to match the assigned burner's BTU rating and flame height
• Helps produce a steady blue flame and even heating when the correct orifice is installed
• Helps with weak/uneven flame, yellow tipping/soot, or delayed ignition if the orifice is blocked or damaged
• Fuel-specific component designed for natural gas systems

• One natural gas orifice

• Shut off gas supply and disconnect power before servicing
• Replace like-for-like; the stamped size/marking matches the burner position and fuel type—do not drill or modify
• Use an appropriate wrench and tighten snugly without overtightening
• Restore gas and leak-test with a soap solution; proper flame.

This water inlet valve controls water flow to the refrigerator's dispenser and ice system so you get a steady supply when needed and stop unwanted leaks. It replaces a worn or failing valve to restore proper water delivery. What it does:

• Opens and closes to allow water into the ice maker and dispenser
• Stops water flow when dispenser/ice fill is inactive
• Commonly replaced when water won't dispense or ice maker won't fill
• Needed if the valve is leaking or causing water drips

• Disconnect power and shut off the water supply before replacing the valve
• Handle with care and inspect inlet/outlet fittings and gaskets for proper sealing
• Reconnect water and power, then check for leaks and proper water flow after installation
• Follow manufacturer instructions

The oven grates are installed on top of the burner elements to hold various types of cookware and protect the burners from damage. Sometimes the grates on top of an oven's burners can become damaged or corroded, and repairing or cleaning won't be enough to fix them. Working grates should always be installed on top of the burners to protect pots and pans from direct heat. These grates also keep the burners from getting damaged. Make sure the old grates aren't hot before you remove them. Wear gloves if possible. Lift up on the old grates to remove them from the burners. Discard them and place the new ones in their old place. Make sure they are locked in place securely and don't sit unevenly.This Frigidaire grate kit is sourced directly from Frigidaire as a genuine OEM replacement part. The component is sold individually. This part is compatible with Frigidaire brand appliances.

This replacement control knob restores smooth, accurate adjustment of your appliance's settings when the original is worn, cracked, or missing. Get a secure grip and the original look with a direct-fit knob that installs in seconds.

• Presses onto the control stem to actuate the underlying switch or valve
• Fixes knobs that are stripped, loose, wobbly, hard to turn, or missing
• Helps when the pointer no longer aligns with settings or the knob spins freely
• Direct-fit design maintains the original feel and operation

• Unplug the appliance or switch off power at the breaker before servicing
• Pull the old knob straight off; avoid bending the control shaft
• Align the new knob's insert with the flat/key on the stem and push fully into place
• Verify smooth rotation and proper engagement of the control

This valve-to-regulator tube carries fuel between the pressure regulator and gas control valve, maintaining a sealed path for proper ignition and stable flame. Replace if the tube is kinked, damaged, or leaking.

• Provides a rigid, factory-formed connection between the pressure regulator and valve
• Helps ensure correct gas flow to the burner system
• Failure signs include weak or no flame, delayed ignition, repeated clicking, or a gas odor
• Visible kinks, corrosion, or stripped fittings indicate the tube should be replaced

• Disconnect power and shut off the gas supply; ventilate the area before servicing
• Use two wrenches to back up fittings; avoid twisting the regulator or valve bodies
• Route the tube without kinks and tighten flare connections securely
• Leak-test all joints with an approved solution—never an open flame—before restoring service.

Restore dependable oven-light operation. This door-activated switch turns the oven's interior light on when the door opens and off when it closes, letting you check food at a glance and preventing the light from staying on unnecessarily. What it does:

• Detects door position to control the oven cavity light on/off
• Worn or stuck contacts can make the light stay on with the door closed
• Failed switch can prevent the light from turning on when the door opens
• Intermittent or flickering light may indicate a failing switch

• 1 switch

• Disconnect power to the appliance before servicing
• Access the switch (typically mounted in the front frame near the door opening)
• Move wires to the new switch one at a time to maintain correct placement
• Reinstall, then test door/light operation before final reassembly

This replacement surface burner control knob restores a clean, precise feel to your range controls so you can set heat levels confidently. Ideal for replacing a cracked, stripped, or missing knob.

• Attaches to the burner valve or switch stem to select heat settings
• Common symptoms: knob wobbles, cracks, slips, or won't stay aligned with settings
• Restores accurate pointer alignment and consistent turning feel
• If the stem itself is damaged, the underlying valve/switch may also need service

• Turn the appliance off and allow all surfaces to cool
• Pull the old knob straight off the stem—do not pry against the panel
• Align the new knob with the stem and press straight on until fully seated at Off
• Rotate through all settings to confirm smooth operation

This is a nut that is used in many microwave ovens. It is typically used to hold interior fan in place. A nut is a fastener that is used to hold two items together or keep one component secure against a surface. Use and time can cause the nut to become stripped, damaged, or broken. If the nut is broken, it will no longer hold the fan in the right location. The nut will need to be replaced.Before replacing this part, the microwave should be unplugged. Open the refrigerator door and remove the cover that goes over the fan. The nut can then be removed using a nut driver. Replace the other parts before using the appliance.This nut is used in microwave ovens manufactured by Crosley, Electrolux, Frigidaire, and Kenmore. It is sold as a single part. This is an authentic OEM replacement part is sourced directly from the manufacturer.

This adhesive faceplate restores the labels and graphics on your oven's electronic control. Replace a faded, bubbled, or peeling overlay so settings and keys are easy to see again for safe, accurate operation.

• Provides printed button labels and display markings for the electronic oven control
• Replaces overlays worn by heat, cleaning chemicals, and normal use
• Common symptoms: faded or unreadable text, bubbling, lifted corners, sticky residue
• Note: Does not resolve unresponsive keys—typically indicates a keypad/touch panel or control issue

• Disconnect power at the breaker before servicing
• Remove trim as needed; gently warm and peel off the old overlay; clean all adhesive residue
• Dry-fit to alignment; peel liner and apply from one edge, smoothing to avoid bubbles
• Press firmly around display and key openings; allow adhesive to set before reassembly

This is the radiant surface heating element that powers one burner on a glass-ceramic cooktop. Replacing a failed element restores fast, even heat and reliable temperature control for everyday cooking.

• Converts electrical energy into heat for a single cooktop zone
• Works with the burner control to cycle on/off and maintain temperature
• Common symptoms include no heat, intermittent heat, or very slow heating
• Visible hot spots, blisters, or cracks on the element indicate failure

• Disconnect power to the range/cooktop before servicing; high voltage is present
• Allow the glass top to cool; lift or remove it to access the element as your model requires
• Transfer wires one at a time to the new element; secure using existing brackets/mounts
• Ensure the element is centered under the glass and test operation before reassembly

This wiring harness connects key components within the appliance, carrying power and control signals where they need to go. Replacing a damaged harness restores safe operation and fixes intermittent failures caused by loose, burnt, or broken connections.

• Routes electrical power and control signals between boards, switches, sensors, motors, and heaters
• Helps resolve symptoms such as won't start, stops mid-cycle, intermittent operation, dead components, breaker tripping, burning smell, or visible melted/brittle wiring
• Restores proper continuity when the original wiring is cut, overheated, corroded, or shorted
• Maintains correct electrical pathways to protect components from further damage

• Disconnect power before servicing; verify no voltage is present with a meter
• Document connector locations and wire routing; take photos for reference
• Release connector locking tabs—do not pull on wires; route in original path using existing clips/retainers, away from sharp edges, heat, and moving parts
• Ensure all terminals are fully seated; test operation before final reassembly

The Burner Valve is an OEM component specifically designed for Frigidaire ranges. It controls gas flow to individual burners, providing a selection of different heat levels when operating the cooktop.

Causes of a bad burner valve can include wear over extended usage periods, damage from water, or gas blockage impeding operation. 

Symptoms of a bad burner valve include:

• Inability to light specific burners or adjust the flame height
• Uneven or intermittent burner performance  
• Gas leaks at burner valve connections
• Recurring error codes due to valve malfunctions

Replacing with this OEM valve restores full functionality to the range cooktop. Compatible with existing gas lines, it supports safe and reliable cooking performance.

This OEM Frigidaire replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. Replace before issues worsen.
 

This oven door glass panel restores a clear, safe viewing window on your range when the original is damaged. Replacing a cracked or shattered pane helps keep heat contained, maintains visibility, and returns the door's appearance.

• Forms the glass window in the oven door to allow viewing while helping contain heat
• Replace if cracked, shattered, loose, or missing to avoid safety risks and heat loss
• Damage can contribute to longer preheat times or poor temperature retention
• Rattling, spiderweb cracks, or sharp edges are common signs it needs replacement

• Disconnect power or switch off the breaker; allow the appliance to cool completely
• Remove the oven door and place it on a padded, stable surface
• Transfer any trim, brackets, handle, and gasket from the original panel; reuse existing screws
• Handle glass with cut-resistant gloves; do not overtighten fasteners; verify door alignment and seals before use

This convection fan motor powers the fan that circulates heated air during convection cooking, helping your appliance maintain even temperatures and consistent results. Replacing a weak or noisy motor restores proper airflow and quieter operation.

• Drives the convection fan to move hot air throughout the cooking cavity
• Promotes even heat distribution for baking and roasting in Convection modes
• Activates when the control calls for convection airflow
• Common symptoms: fan not spinning, intermittent or slow operation, rattling or squealing noises, uneven cooking

• Disconnect power and allow the appliance to cool completely. Microwaves can retain dangerous high voltage even when unplugged.
• Access the motor behind the rear or interior fan cover per your model's design.
• Note wire positions; transfer the existing fan blade and any mounting hardware to the new motor if required.
• Ensure the fan spins freely before reassembly; restore power and test a Convection cycle.