Estate Agitator Parts

This upper agitator—also called the clothes mover—is the top section of the agitator in select top-load washers. It works with the agitator cam and dogs to roll laundry over during wash strokes. Replace if cracked, stripped, or no longer engaging. What it does:

• Provides the upper vanes that lift and roll clothes for proper turnover during agitation
• Transfers one-way motion from the cam/dogs to the top section of the agitator
• Helps address symptoms like the top section free-spinning, poor turnover/cleaning, rattling/loose feel, or visible cracks/broken fins

• 1 upper agitator (clothes mover)

• Unplug the washer and turn off water before servicing
• Remove the dispenser and cap to access the center fastener; lift out the agitator assembly
• Separate the old upper section from the cam, seat the new clothes mover fully on the splines, and reassemble
• Hand-check for one-way engagement of the top section before running a test cycle

This Agitator Auger is the upper half of a dual-action washer agitator. It works with the agitator cam and dogs to create the screw-like motion that pulls clothes downward; replace if the top agitator slips, cracks, or stops turning.

• Forms the upper agitator that produces the ratcheting, spiral action for proper wash turnover
• Common symptoms include the upper agitator not moving, free-spinning or slipping under load, and visible cracks or stripped splines/fins
• Restores correct clothing movement and agitation performance when the upper section no longer drives

• Disconnect power and water before servicing
• Remove the fabric softener dispenser and inner cap, then unbolt and lift off the agitator to access the auger
• Transfer internal components (cam and agitator dogs) if reusing; inspect for wear during reassembly
• Align splines, seat the auger fully, tighten fasteners securely, and test the agitation function

This agitator drive shaft sits inside the washer's gearcase and transfers motion to the agitator. Replacing a worn or stripped shaft restores firm engagement and reliable wash action while helping reduce slip and grinding during agitation.

• Transfers oscillating motion from the transmission to the agitator
• Provides the splined interface that engages the agitator/coupler
• Common symptoms include no agitation, intermittent/slipping agitation, or grinding/clicking from the gearcase
• Visible wear, rounded splines, or a bent shaft can lead to a loose or non-moving agitator

• Disconnect power and water; use proper PPE
• Requires removing the cabinet and gearcase; drain and reseal the gearcase per service procedures
• Keep gears, spacers, and clips in order; reassemble in the original orientation
• Inspect mating parts (agitator coupler/splines, drive block, seals) and replace if worn

This washer agitator is the central wash-motion component. It mounts to the drive hub and churns laundry through water and detergent, restoring proper turnover when the original agitator is cracked, stripped, or missing.

• Creates the back-and-forth wash action that moves clothes through the wash water
• Restores proper turnover and cleaning when the old agitator is damaged or worn
• Typical symptoms: no or weak agitation, clothes not moving, clicking/ratcheting from the agitator area, or a loose/wobbly agitator
• Visual issues may include cracks, stripped splines, or a unit that lifts off easily

• Disconnect power and shut off water before servicing; wear cut-resistant gloves
• Remove the softener dispenser and cap, then the center bolt/retainer; pull the old agitator straight up
• Align splines and seat the new agitator fully; reuse existing bolt and cap unless damaged
• Do not overtighten the fastener; run a short test cycle to ensure proper agitation

This is the central wash-action component in select top-load washers. Replacing a worn or damaged agitator restores proper agitation so clothes circulate through water and detergent for consistent cleaning performance. What it does:

• Converts drive motion into the back-and-forth action that moves laundry
• Circulates clothes to improve soil removal and reduce tangling
• Replaces cracked, stripped, or loose agitators that cause weak or no agitation
• Common symptoms include poor cleaning, clothes not moving during wash, or an agitator that wobbles or spins freely by hand

• 1 agitator assembly

• Disconnect power and turn off water supply before servicing
• Remove the fabric softener dispenser and inner cap to access the center bolt
• Remove the bolt, lift off the old agitator, seat the new agitator on the splined shaft, and secure the bolt
• Reinstall the cap/dispenser; reuse original hardware as applicable and check for a secure fit before testing

This is the washer's agitator assembly with a built-in filter. Replacing a worn or damaged agitator restores proper turnover of clothes and helps capture lint during the wash for cleaner results.

• Drives the back-and-forth wash action that circulates and rolls laundry
• Integrated filter helps collect lint and debris from wash water
• Worn fins or a stripped hub can cause weak or no agitation and poor cleaning
• A missing/damaged filter may lead to excess lint on clothing

• Disconnect power before servicing; turn off water supply for safety.
• Remove the softener cup/center cap; take out the center bolt or retainer if equipped.
• Lift the old agitator straight up; align splines and press the new agitator fully into place.
• Reinstall the fastener and cap; run a short cycle to confirm proper agitation.

This agitator replaces the top agitator in compatible top-load washers to restore proper fabric movement and cleaning action. It helps re-establish the washer's normal wash motion and reduces poor wash performance caused by a damaged agitator. What it does:

• Replaces a cracked, worn or broken top agitator to restore wash motion and even water circulation
• Helps fix symptoms such as clothes not tumbling, uneven cleaning, or excessive vibration during the wash cycle
• Transfers torque from the transmission to move clothes through the wash water
• Works with the factory agitator coupler/bolt and transmission components when installed correctly

• One top agitator assembly

• Disconnect power and water supply before beginning any repair
• Remove the fabric softener dispenser and the agitator cap to access the retaining bolt
• Tighten the retaining bolt to the manufacturer's specified torque and confirm proper engagement with the cam/coupler

Some assembly required.