Estate Switch

• Doesn't shut off
• Won't start
• Will not tumble

I realized my load of laundry was still wet after a normal drying cycle. My first action was to turn the dryer on (2010 gas Maytag centennial) and open the front port to look at the ignitor coil. It never turned orange so I knew there must be a problem with the primary circuit. I shut off the dryer, disconnected the power, pulled it away from the wall, shutoff the gas, and removed the back panel. I then disconnected the wires for the thermal fuse and checked its resistance with a multimeter.... Read more

• Won't start
• Element will not heat

The fix was to replace the infinite control switch on my Whirlpool range. A simple task. Read more

• Won't start
• Timer will not advance
• Will not drain

First I checked the circuit breakers and power to the outlet, then next wanted to check the lid switch, but it wasn't where I had found it on older models. I could hear it clicking on and off as I raised and lowered the lid, but it wasn't visible. I drained the tub through a siphon hose to lighten the machine, so I could slide it away from the wall to better see. Couldn't see the switch anywhere and decided it must be hiding in the raised console, but was unsure of how to attack it without... Read more

• Element will not heat

Replaced the burner Infinite switches for the burners having the issue. Here are the latest part numbers for this model Maytag. Left rear (LR) and right rear (RR) burners are both 6" and use the same switch. Part # WP3149404. Left front (LF) is an 11 1/2" burner Part# W10167742. The right front (RF) burner is a double burner 6" center and 9 1/2" outside burner Part #WPW10149355. Very simple repair. Unplug the stove, remove the rear panel, remove the switch knob, remove the 2 switch screws,... Read more

• Will not drain
• Won't start
• Will not fill with water
• Lid or door will not open

My son was doing his laundry, only to announce that the washer wouldn't rinse, spin or drain. I looked on line at new washers and was staggered to see how much they cost, our Whirlpool is 20 years old! Then I looked on Craig's list to see about getting a used washer, but when I found something that looked good, and looked up how it performed, most of them had terrible reviews. So, I looked at a video that told about the 5 most common things to go wrong and figured out it was a broken lid... Read more

I watched the video on replacing the switch on a side freezer where prying out to original switch did not look difficult. I then got on the floor and tried to pry out my switch. Had a terrible time (locking tab or switch body hardened with time?) and mangled the switch terribly and the upper panel of the freezer somewhat, but the switch did come out. AND THEN the top freezer panel with the switch and light assembly fell out into my hands! I was able to unplug one Molex connector and the... Read more

After checking other reviews, we decided it was best to replace the interlocks, cam and all three switches. You're going to need a phillips screwdriver, star driver, small screwdriver and needle nose pliers. You need to remove the ONE Phillips screw above the control panel inside the vent. The contol panel is on hinges that you can slide up and towards you. Using caution remove the wires noting how they're connected. Pinch the top of the white connectors and wiggle them free. We couldn't get... Read more

Replaced door switch - it took less than 5 minutes - works perfectly Read more

• Will not drain
• Pumps but will not spin
• Timer will not advance
• Doesn't shut off

The lid shut-off switch is located behind the lid How About That. I order the plastic ball the hold the lid in place plus the lid shut off switch. I watched the video that AppliancePartsPros.com has on how to replace the lid and the plastic balls. I removed the lid to get to the two philips head screws to remove that part of the shut-off switch. I took the new switch out of the package and compared it to the old switch. I assembled the switch just like the old switch look using the new... Read more

After checking other reviews, we decided it was best to replace the interlocks, cam and all three switches. You're going to need a phillips screwdriver, star driver, small screwdriver and needle nose pliers. You need to remove the ONE Phillips screw above the control panel inside the vent. The contol panel is on hinges that you can slide up and towards you. Using caution remove the wires noting how they're connected. Pinch the top of the white connectors and wiggle them free. We couldn't get... Read more

I first diagnosed the problem by replacing the burner control (Infinite switch) with one from a smaller burner (one that I knew worked fine). That seemed to solve the problem. I ordered the correct control for the big burner on Saturday night, it arrived Tuesday and installed it in less than 10 minutes using only a Phillips screwdriver. Remember to unplug the stove before performing any service. Take this time to clean around and under the stove. (You know it needs it!) Read more

• Not dispensing water

I watched the Appliance Parts Pros repair video and decided to remove the front panel to diagnose the problem. While the repair video is excellent, I could not remove the ice/water dispenser front panel with a putty knife. On my model, 106.56234400, there is no clip that can be released by sliding a putty knife up under the front panel. It took a little effort but I was able to pop the left lower corner clip just by pulling it out with my fingers. Once the cover was off I could see that the... Read more

• Doesn't shut off

Background: Roper Electric Dryer model REX6634RQ0 purchased new in early 2006 by my wife. Dryer use profile is low to moderate as it was used by only one person (working from home) from 2006 to late 2007 then moved and stored in a dry basement until mid 2009. Moved and used by primarily just two people (plus occasional children visits) from mid-2009 thru late 2011 with three moves involved with in that time. Then stored in a dry shipping container until moved again in 2013. The multiple... Read more

Replaced the duct tape with a new switch Read more

• Won't start

I replaced the lid switch using the parts I purchased from applianceparts.com. The control panel had to be removed first and then the cabinet. Read more

• Light not working

We had delayed repairing the problem because we received a price of more than $ 100 from a local appliance repairman. However, after viewing the view on the ApplianceParts Pro website, I saw what an easy repair it would be. After receiving the part from you, I had my son do the repair because I felt it would a good father - son bonding time. It was so easy and he was proud of his ability. Thanks for your excellent repair video and the excellent price. It costs less than $ 22 instead of more... Read more