Estate Bracket & Flange

The Spring Mounting Bracket is an OEM part for Whirlpool washing machines. It is located at the bottom of the appliance, near the base. It provides a secure attachment point for the suspension springs, which help absorb vibrations and stabilize the drum during operation.

Causes of a faulty spring mounting bracket can include regular wear and tear, physical damage, or improper installation. These factors can result in issues such as excessive shaking or movement of the appliance, increased noise during operation, or unbalanced loads.

Symptoms of a bad spring mounting bracket may include:

• Excessive shaking or movement of the appliance during operation
• Increased noise or rattling sounds during the wash or drying cycle
• Unbalanced loads, causing the drum to tilt or not spin properly

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

This hinge receiver mounts to the appliance frame and accepts the door hinge arm/pin. It keeps the door aligned and secure so it opens and closes smoothly. Replacing a worn or cracked receiver restores proper door action.

• Anchors the hinge arm/pin at the cabinet/frame for smooth door movement
• Maintains door alignment and consistent closing action
• Wear or damage can cause a loose or sagging door, misalignment, or binding
• Common signs include clicking/grinding noises and visible cracks or deformation

• Disconnect power; allow the appliance to cool and shut off gas/water if applicable
• Support or remove the door to access the receiver
• Remove mounting fasteners, swap in the new receiver, and align per service instructions
• Reinstall the door and verify smooth movement and full closure

This rear panel support is the structural bracket that secures the appliance's rear cover/backguard in place. Replacing a worn or broken support restores proper alignment, helps protect internal components, and reduces vibration noise.

• Secures the rear panel/backguard to the chassis for stable, proper fit
• Maintains alignment of panels and mounting points
• Helps minimize vibration, flexing, and rattles from a loose rear panel
• Common signs of failure: cracked or missing bracket, stripped mounting points, panel movement or buzzing

• Disconnect power at the breaker; shut off gas supply
• Pull the appliance forward carefully to access the back; protect flooring
• Remove fasteners, replace the damaged support, and reuse original hardware/clips
• Keep wiring clear of sharp edges; tighten screws evenly without over-torquing and check for vibration before repositioning

Replace a worn or misaligned interlock with this microwave door interlock assembly. It aligns and supports the door switches so the control accurately senses a fully closed door, restoring safe, reliable operation.

• Interfaces with the door latch hooks to actuate the safety door switches
• Ensures the microwave only runs when the door is fully closed
• Useful when the original interlock is cracked, loose, or out of alignment

• Disconnect power before service; microwaves can retain dangerous high voltage even when unplugged
• Access is typically behind the control panel; over-the-range units may need to be taken down for service
• Mount securely and verify the door latch hooks smoothly actuate the switches
• After reassembly, test door closure and start/stop operation before regular use

This motor retainer secures the motor to its mounting point, keeping the assembly tight and aligned. Replace a worn or broken retainer to cut vibration and noise and to protect nearby seals, wiring, and components. What it does:

• Holds the motor firmly in place within the assembly
• Maintains alignment for smooth, quiet operation
• Supports sealing surfaces and connections; on water-bearing assemblies, help prevent leaks
• Replace if you notice a loose or rattling motor, new vibration/noise, or signs of movement or leakage at the motor

• Includes 1 motor retainer.

• Disconnect power; turn off water supply.
• Access the motor area and support the motor before removing the old retainer.
• Inspect mating parts and seals; replace any damaged components.
• Fully seat the motor and install the new retainer securely; test for abnormal noise or leaks.

The Anti Tip Bracket is an OEM component specifically designed for Whirlpool ranges. This bracket plays a crucial safety role in preventing the range from accidentally tipping over if excessive weight is applied to the open oven door. 

The anti-tip bracket secures tightly to the floor or wall behind the range, linking it securely in place. It allows the oven door to function while ensuring the entire appliance remains stable even under heavy use. 

Causes of a bad bracket can include damage, deterioration of mounting hardware over time, or failure to install properly according to manufacturer instructions. 

Symptoms of a faulty anti-tip bracket include:

• The range appears unsecured and able to wobble or rock backward 
• Looseness between the bracket and mounting surface
• Cracks or breaks in the anti-tip bracket material

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. 
 

This mounting bracket secures a designated component to the appliance frame, keeping it properly positioned and stable. Replacing a bent or broken bracket restores support and helps eliminate looseness, vibration, and misalignment during operation.

• Anchors the specified part to the chassis or panel
• Maintains proper alignment and clearances for reliable performance
• Helps prevent vibration, rattling, or shifting during use
• Common signs of failure: bent or cracked bracket, loose or misaligned components, new rattling noises

• Disconnect power and allow any hot surfaces to cool before servicing
• Note the original bracket's orientation and fastener locations for accurate reinstallation
• Transfer and tighten existing hardware securely without overtightening
• After installation, verify the supported part is secure and properly aligned

This anti-tip bracket kit is an OEM replacement part for Whirlpool ranges. This bracket is typically installed at the back of the range and is secured to the wall or floor to prevent the range from tipping forward when heavy items, such as pots or pans, are placed on the open oven door.

The anti-tip bracket should be installed during the initial installation of the range and checked regularly to ensure that it is securely attached. If the bracket becomes loose or damaged in any way, it should be replaced immediately to ensure the safety of the range and anyone using it.

This kit includes:

• Anti-tip bracket
• Mounting screws (2)
• Anchors (2)
• Washer (1)

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

This mounting bracket secures internal components in place to keep your appliance stable and operating quietly. It replaces a worn, bent, or broken bracket to restore proper alignment and prevent loose or rattling parts. What it does:

• Provides a stable mounting point for panels, assemblies, or hardware
• Keeps connected components aligned to prevent rubbing or vibration
• Stops noises caused by loose or shifting internal parts
• Restores proper fit when an old bracket is bent, cracked, or missing

• Install with appliance unplugged or power disconnected to avoid shock
• Verify bracket orientation using the appliance's service diagram before fastening
• Use appropriate screws/fasteners and torque to avoid stripping or distortion

This mounting bracket secures appliance components to the cabinet or chassis, restoring proper alignment and reducing movement. It's a direct-fit structural support used where panels or assemblies need a stable attachment point. What it does:

• Secures panels, trim or internal assemblies to the appliance cabinet to prevent shifting or sagging
• Restores proper alignment to reduce vibration, rattling or scraping noises
• Helps maintain door and panel fit for correct operation and appearance
• Used when a broken, bent or missing bracket causes loose or misaligned parts

• Disconnect power and water before starting any repair
• Verify bracket orientation and location against the appliance before tightening
• Use original mounting hardware when possible; inspect screws or clips and replace if worn

The ice maker bracket is an OEM part for Whirlpool refrigerators. This bracket is a structural component that holds and supports the icemaker assembly within the refrigerator. It allows for secure mounting and installation of the icemaker while also maintaining proper alignment.

Causes of a bad bracket can include wear and tear over time, cracks or breaks due to impact or stress, or corrosion issues that compromise the integrity of the mounting structure.

Symptoms of a bad bracket include:

• Loose or unstable icemaker installation
• Improper ice production or dispensing
• Noise or vibrations emanating from the icemaker area
• Moisture leaks or water damage near the bracket mounting points

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This control bracket secures the appliance control or console assembly, keeping the control board and user interface stable for reliable operation. It helps prevent loose or misaligned controls that can affect button response or display visibility. What it does:

• Provides a rigid mounting surface for the control board or console assembly
• Keeps control components aligned and stable during normal use
• Helps reduce vibration-related connector or wire stress
• Can restore proper fit and button alignment when the panel is loose

• One control bracket

• Disconnect power to the appliance before starting any repair
• Handle the control board and wiring harness carefully to avoid damage
• Basic hand tools (screwdriver, nut driver) are typically required for removal/installation
• Reuse existing screws or verify hardware compatibility