Estate Agitator Parts

• Will not agitate
• Spins slowly

I had previously replaced the pump about 1 year ago. That was not the problem. Still leaked the same way - intermittently, but always in the center of the washer onto the floor. None of the hoses were leaking - no evidence of corrosion or water mineral residue at any of the hose fittings. So, it must have been something else. I studied the parts diagram for the washer tub assembly and concluded the source of the leak almost had to be the outer tub's Centerpost Gasket. It was really the... Read more

I had previously replaced the pump about 1 year ago. That was not the problem. Still leaked the same way - intermittently, but always in the center of the washer onto the floor. None of the hoses were leaking - no evidence of corrosion or water mineral residue at any of the hose fittings. So, it must have been something else. I studied the parts diagram for the washer tub assembly and concluded the source of the leak almost had to be the outer tub's Centerpost Gasket. It was really the... Read more

I searched the internet for the most likely cause of the problem and then went to the AppliancePartsPros.com site to see if they had the parts. Naturally they did, but the best part was that they had a video on how to change the part. The video was very clear and straightforward. So easy to follow. I ordered the part mid-day on a Thursday. Imagine my surprise when later that day an email came in letting me know that the part was already shipped! The next day the part was on my front... Read more

Installed new agitator Read more

• Shakes and moves
• Noisy
• Pumps but will not spin

Replaced washer drive block and Cam. I called around and finally settled on Appliance Parts Pros because they helped diagnose the problem, told me what parts to replace and had videos to show me how to do it. In completing the repair I had to remove quite a few pieces of hardware in order to get at the part I was to replace. The videos helped but there is a learning curve while you familiarize yourself with the parts and figure out how the remove them. Eventually I got to a large nut that,... Read more

I had replaced the Agitator cams a couple of times already due to my brother-in-law overloading the machine which stripped the teeth off of the cams. I also noticed the agitator seemed to 'wobble' and made 'knocking' noises quite a bit. I reviewed the video on the Appliance Parts Pros web site, disassembled the agitator and cleaned everything up, which helped a little, but not enough. Figuring the agitator itself was worn out also, I looked up and ordered all the parts for the upper agitator on... Read more

Pulled the washer apart (using your videos as a refresher) and found that the plastic coupling between the motor and the transmission had failed. Searched for parts vendors and found your site. Ordered the coupling on-line and went back down to clean up the machine. In the cleaning process I found a damaged thrust washer for the upper agitator and broken drive dogs for that same agitator. I went to the website to see if I could augment my initial order. I did not want to pay shipping costs... Read more

I had to replace the drive shaft and the lower agitator. The motor coupling was also worn out. The repair was challenging because I had to rebuild the gear box. This step was really messy and I had to wait for the liquid gasket to set prior to completing the repair. Cleaning and prep of all of the parts tripled the repair time. Read more

I had replaced the Agitator cams a couple of times already due to my brother-in-law overloading the machine which stripped the teeth off of the cams. I also noticed the agitator seemed to 'wobble' and made 'knocking' noises quite a bit. I reviewed the video on the Appliance Parts Pros web site, disassembled the agitator and cleaned everything up, which helped a little, but not enough. Figuring the agitator itself was worn out also, I looked up and ordered all the parts for the upper agitator on... Read more

Used the parts and youtube video from your company. Read more

The ridges inside the agitator base were stripped. Installed a new base - after a good cleaning of build-up on the spindle. Works like new! Read more

I watched a few on line videos. Found 2 easy things to check. The motor coupler then the clutch. It took me about 30 minutes to get everything apart and find out which problem it was. Went on line to Appliance Pros.com and ordered the new clutch.It came in 2 days. Took less than 30 minutes to get it on and get everything back together. It was awesome. Read more

Slipped old one off slipped new one on Read more

I had replaced the Agitator cams a couple of times already due to my brother-in-law overloading the machine which stripped the teeth off of the cams. I also noticed the agitator seemed to 'wobble' and made 'knocking' noises quite a bit. I reviewed the video on the Appliance Parts Pros web site, disassembled the agitator and cleaned everything up, which helped a little, but not enough. Figuring the agitator itself was worn out also, I looked up and ordered all the parts for the upper agitator on... Read more

My wife noticed that our washing machine was making a terrible rumbling noise and seemed to be out of balance all of the time. She was on the verge of calling a repairman when I said I wanted to look at it first. I noticed the agitator was very loose and would spin in your hand. I removed 1 bolt and the agitator was out. The teeth in the agitator were stripped out so by simply ordering a new agitator and installing it I turned a $250.00 repair call into a $70.00 DIY fix. Thanks. Read more

Bought a new upper agitator/filter housing. Just slide it over the bottom agitator housing and put the cap from the old one on the new one. Takes maybe 3 minutes to do. The screen inside the lower part of the housing/filter holds it snug to the bottom housing and does not fly off during the spin cycle. Works great. Read more