Parts for Ge PSSF3RGZBCC: 01 - Freezer Door Parts

Replacement mounting screw for refrigerator panels, brackets, and internal components. Secures loose assemblies when original fasteners are stripped or missing.

White door handle assembly for side-by-side refrigerators. Replaces cracked, broken, or worn handles. Installs on refrigerator or freezer doors.

Replaces a broken or missing dispenser door stop on side-by-side refrigerators. Closes and seals the ice/water dispenser opening when not in use.

This white stop door replaces the dispenser stop/door that controls access to the ice/water chute, helping restore proper dispenser operation and reduce sticking or unwanted discharge. Designed to match the original OEM fit and appearance. What it does

• Seals and releases the dispenser opening so ice or water is dispensed only when the door is actuated
• Replaces a cracked, warped, or jammed stop door that can cause sticking or partial openings
• Helps prevent accidental drips or debris entering the dispenser chute
• Restores a smooth, aligned door movement for reliable dispensing

• One white stop door

• Disconnect power to the appliance before starting any repair
• Remove dispenser housing or outer door per the service manual to access the stop door
• Inspect the actuator and mounting tabs for damage; replace if worn to ensure proper operation
• Use basic hand tools;

Stops refrigerator door from opening past 90 degrees. Mounts at base of door with screws. Replace if cracked, broken, or bent to prevent door overswing.

Seals refrigerator door to maintain temperature and prevent warm air entry. Replace if torn, cracked, or causing frost buildup. Verify fit with your model.

White plastic cam closure that aligns and secures the freezer door in the hinge area. Replace if cracked, broken, or worn to restore proper alignment.

Replaces a broken or worn freezer door cam closure on side-by-side refrigerators. Installs on the door to control opening range and secure latching.

Molded trim piece that supports and secures the front grille on side-by-side refrigerators. Replace if cracked, broken, or missing to restore fit.

Replace your refrigerator's dispenser drip tray if cracked, stained, or missing. Catches water and ice drips in the dispenser recess for a clean look.

Replacement dispenser grill recess drip tray for side-by-side refrigerators. Collects spills and overflow in the dispenser area. Replace if cracked or missing.

Ice won't dispense or dispenser flap sticks open? The ice dispenser solenoid controls ice flow. DIY-friendly repair with our install video.

The recess door retainer secures the dispenser's ice chute flapper in the refrigerator door. Replacing a cracked or missing retainer restores proper flapper pivot and sealing to help reduce frost buildup and air leaks around the dispenser.

• Holds the recess/ice door on its pivot within the dispenser assembly
• Helps the flapper close fully to seal the ice chute
• Restores smooth open/close action of the dispenser door
• Common symptoms: loose or fallen flapper, poor chute seal, frost or condensation in the dispenser area, and ice clumping near the chute

• Unplug the refrigerator before servicing the dispenser
• Carefully remove the dispenser bezel/control panel to access the ice chute door assembly
• Note spring orientation and retainer position; transfer components to the new retainer
• Verify flapper movement and seal before reassembly and restoring power

If your dispenser light stays off or won't turn on, this control board restores proper illumination. Moderate DIY, requires clip release and wiring.

Bisque dispenser housing shield for side-by-side refrigerators. Replaces cracked, broken, or discolored dispenser covers. Installs on front panel.

Fix a damaged or cracked dispenser front with this housing shield. Protects internal components and restores a finished look to your refrigerator's exterior.

Ice dispenser door assembly seals the ice chute opening on your refrigerator. Replace if cracked, warped, or the rubber gasket is damaged and leaking air.

Restores closing tension for refrigerator ice dispenser recess door. Replace if spring is weak, broken, or missing to keep door closing properly.

Connects the actuator to your refrigerator's ice chute door. Replace if cracked, broken, or worn to restore proper door operation and seal.

Replaces a cracked, broken, or worn ice chute funnel in your refrigerator door dispenser. Directs ice from the auger to your glass or container.

This white ice dispenser paddle is the lever you press on the freezer door to release ice. Replacing a worn or broken paddle restores reliable ice dispensing and a clean, like-new look at the dispenser.

• Transfers your push to the dispenser switch to start ice delivery
• Helps fix a cracked, broken, loose, or missing paddle
• Addresses a lever that sticks or doesn't return smoothly
• Useful when ice won't dispense unless the switch is pressed directly
• Refreshes a yellowed or scuffed dispenser paddle

• Disconnect power to the refrigerator before servicing
• Remove the drip tray and dispenser trim/control panel to access the paddle
• Note spring/lever orientation and transfer any hardware from the original paddle
• Reassemble, restore power, and test ice dispensing

Replacement paddle for refrigerator ice dispenser. Press to activate ice release. Replace if cracked, broken, or won't spring back after pressing.

Water or ice dispenser not working? This dispenser switch activates when you press the lever. Easy DIY repair—takes about 30 minutes with basic tools.

Spring that controls dispenser arm movement in refrigerators. Installs on the paddle assembly. Replace if broken, detached, or missing to restore arm function.

Connects water supply tubing sections in your refrigerator. Replace this plastic compression union if it's cracked, leaking, or broken. Installs inline.

Lever lock secures your refrigerator door handle assembly. Replaces broken or missing locks that allow handle to loosen or detach from door.

Replace your broken or cracked refrigerator freezer door module support bracket. Secures door bins and shelves in place. Direct fit replacement part.

Restores a stable storage surface inside your freezer. Replace this freezer shelf if cracked, warped, missing, or no longer seats securely in supports.

Wire tilt-out door basket for refrigerator doors. Replaces broken, cracked, or missing baskets. Installs in door to organize and store smaller items.

Handle lock bracket for refrigerator doors. Secures handle locking mechanism in place. Replace if bracket is cracked, broken, or missing for proper fit.

Wiring harness for the recessed dispenser area of your refrigerator. Replace if wires are damaged, frayed, or connections are loose or corroded.

Bottom freezer door plug insert for side-by-side refrigerators. Replaces cracked, broken, or missing inserts to restore door appearance and seal.

Plastic bushing that fits inside the lower freezer door hinge assembly. Replace when cracked, worn, or broken to restore smooth door operation.

Replacement mounting screw for refrigerator panels, brackets, door handles, and trim. Needed when original hardware is missing, stripped, or corroded.

Door hinge thimble for side-by-side refrigerators. Installs on the door hinge assembly. Replace if cracked, broken, or worn to restore proper alignment.

Door hinge thimble for side-by-side refrigerators. Installs on the door hinge assembly. Replace if cracked, broken, worn, or missing for proper alignment.

Bushing that lines the upper hinge pin on refrigerator doors. Replace if cracked, worn, or missing to restore smooth door swing and proper alignment.