Parts for Ge ZISP480DXCSS: Freezer Door Parts

Replace your refrigerator water filter every 6 months to maintain clean water and ice. Removes contaminants for fresh taste. Easy DIY install in minutes.

Assorted fasteners for securing refrigerator trim, panels, and components. Replace missing, stripped, or damaged screws and clips for proper assembly.

The recess door retainer secures the dispenser's ice chute flapper in the refrigerator door. Replacing a cracked or missing retainer restores proper flapper pivot and sealing to help reduce frost buildup and air leaks around the dispenser.

• Holds the recess/ice door on its pivot within the dispenser assembly
• Helps the flapper close fully to seal the ice chute
• Restores smooth open/close action of the dispenser door
• Common symptoms: loose or fallen flapper, poor chute seal, frost or condensation in the dispenser area, and ice clumping near the chute

• Unplug the refrigerator before servicing the dispenser
• Carefully remove the dispenser bezel/control panel to access the ice chute door assembly
• Note spring orientation and retainer position; transfer components to the new retainer
• Verify flapper movement and seal before reassembly and restoring power

Spring that provides closing tension for the refrigerator water/ice dispenser door flap. Keeps the dispenser sealed when not in use. Replace if door hangs open or won't close.

Replacement top hinge assembly for side-by-side refrigerator freezer doors. Needed when the hinge is cracked, broken, or worn causing door misalignment.

Bottom hinge bushing for refrigerator freezer doors. Installs at the lower hinge to help the door pivot smoothly. Replace if worn, cracked, or missing.

Door gasket and label assembly creates an airtight seal to keep cold air in and moisture out. Replace when worn or damaged to restore efficiency. Verify fit.

Replaces a cracked, broken, or missing door bin on your side-by-side refrigerator. Restores secure storage for bottles, jars, and condiments.

Plastic shield that covers the water and ice dispenser housing on your refrigerator door. Replace if cracked, warped, or broken from impact or heat damage.

This is the ice chute funnel that guides ice from the dispenser mechanism into your glass on the exterior of the refrigerator door. It channels crushed or cubed ice downward through the dispenser opening to prevent spillage. Replace this funnel if ice is scattering, jamming, or missing the glass during dispensing - often caused by cracks, warping, or a broken lever on the funnel assembly.

Water or ice dispenser not working? This dispenser switch activates when you press the lever. Easy DIY repair—takes about 30 minutes with basic tools.

The Torsion Spring is an OEM part for GE refrigerators. It is essential for maintaining the proper tension and operation of the refrigerator door. This spring ensures the door closes smoothly and stays securely shut, preventing cold air from escaping and maintaining the appliance’s efficiency.

Causes of a bad torsion spring can include metal fatigue from regular use, corrosion from exposure to moisture, or damage due to excessive force or mishandling. Over time, these factors can weaken the spring, affecting the door’s performance.

Symptoms of a bad Torsion Spring include:

• Door not staying closed
• Difficulty in opening or closing the door
• Door feels loose or unbalanced
• Unusual noises when operating the door

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Directs and protects your refrigerator lamp for even interior lighting. Replace if cracked, discolored, or light appears dim. Confirm fit with model number.

Fix a light that won't turn on or flickers in your refrigerator. This E12 socket replacement is straightforward with our step-by-step video guide.

Illuminates water and ice dispenser area for visibility in low light. Replace when bulb burns out or dispenser area stays dark. Confirm fit with model.

Replacement dispenser door recess crank for refrigerators. Operates the ice/water dispenser door mechanism. Replace if broken, worn, or corroded.

Stainless steel door handle for freestanding freezers. Replace your cracked, broken, or missing handle to restore easy door access and appearance.

Ice won't dispense or dispenser flap sticks open? The ice dispenser solenoid controls ice flow. DIY-friendly repair with our install video.

Replacement drip tray for refrigerator water and ice dispensers. Catches drips and spills at the dispenser. Replace if cracked, broken, or stained.

Fix dispenser lights not working or unresponsive touch controls. This glass touch dispenser assembly restores water and ice dispensing on your refrigerator.

Black plastic funnel extension attaches to the front of your refrigerator's ice dispenser. Replace if cracked, broken, or missing to reduce splashing.

Bottom door hinge for refrigerators and freezers. Secures and supports the lower door edge. Replace if cracked, bent, or worn to restore proper alignment.

This stainless steel hex cap screw fastens appliance panels and components where a 1/4-20 threaded fastener is required. Durable corrosion-resistant finish helps maintain secure mounting and reliable operation. What it does

• Secures panels, brackets, and internal components to frame or chassis.
• Replaces stripped, rusted, or missing mounting screws that cause loose or rattling parts.
• Restores proper alignment and prevents movement that can lead to wear or noise.

• Use the correct 1/4 in hex socket or wrench; avoid rounded or worn tools.
• Tighten until snug; do not over-torque — overtightening can strip threads or crack plastic parts.
• Replace any damaged mating hardware (nuts, clips, or threaded inserts) for a secure fit.
• Power tools may be used carefully on low torque settings to avoid over-driving.

Set screw for freestanding freezers and refrigerators. Secures internal components and panels. Replace if screw is stripped, missing, or damaged.

This is a small plastic end cap that fits onto the end of the refrigerator or freezer door handle, giving it a finished appearance. It snaps into place to cover the exposed end of the handle mounting hardware. Replace this cap if it is cracked, missing, or discolored, which can leave the handle looking incomplete and expose sharp edges.