Parts for Ge PFE28RSHCSS: Freezer Shelves Parts

This is a replacement #8-18 by 1/2-inch appliance screw used to secure panels, trim, and internal components. It restores proper fastening where the original screw is missing, stripped, or corroded. What it does:

• Fastens panels, brackets, trim pieces, and small components
• Restores secure mounting when a screw is missing or worn
• Stops rattling and vibration caused by loose or stripped fasteners
• Compatible with applications that call for a #8-18 x 1/2" screw

• One screw (8-18 x 1/2 in)

• Use the correct screwdriver or driver bit to avoid stripping the head
• Do not overtighten; stop when the component is snug to prevent damage
• If screw threads are damaged, replace with the correct thread size rather than forcing
• Disconnect power before working on electrical components or panels that expose wiring

This mounting screw secures appliance components to the chassis for a tight, rattle-free fit. Replacing a missing, stripped, or corroded fastener helps keep panels, brackets, or burner assemblies properly aligned and secure.

• Fastens designated parts to the appliance frame or mounting points
• Helps maintain proper alignment of panels, trim, brackets, or burner assemblies
• Restores hold when the original screw is worn, rusted, or lost
• Symptoms include loose or wobbly components, rattling/vibration, or visible gaps

• Disconnect power; allow all surfaces to cool. For gas units, also shut off the gas supply.
• Use the correct driver/bit; avoid cross-threading.
• If mating threads or clip/nut are damaged, repair or replace them before installing.
• Tighten until secure; do not overtighten to prevent stripping.

The Basket Bottom Asm is an OEM part for GE refrigerators. This assembly is specifically designed to fit in the bottom freezer compartment, providing a convenient and organized storage solution for your frozen foods.

A bad bottom freezer basket assembly can occur due to wear and tear, accidental damage, or other factors. If you notice symptoms such as broken wires, a loose fit, or difficulty in sliding the basket, it may be time to replace it with a new one.

Symptoms of a bad bottom freezer basket assembly include:

• Broken wires
• Loose fit in the freezer compartment
• Difficulty in sliding the basket in and out

Improve your freezer storage and organization by replacing the faulty bottom freezer basket assembly with this genuine OEM part.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

The Lower Drawer Gear is an OEM replacement part for GE refrigerators. It plays an important role in allowing smooth operation of the lower freezer drawer. The drawer gear mechanism helps guide and support the drawer assembly during opening and closing. 

Symptoms of a bad lower drawer gear include:

• The drawer failing to slide open or close properly
• Increased resistance or friction when operating the drawer  
• Noisy or grinding sounds coming from the drawer area
• The drawer becoming misaligned or sidetracked from its rails

Causes of a bad lower drawer gear can be wear and tear over extended use. Exposure to excessive weight or strain on the drawer can potentially damage the gear components over time.

Note: Right Side

This OEM GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Left side

The Basket Bottom Asm is an OEM part for GE refrigerators. This assembly is specifically designed to fit in the bottom freezer compartment, providing a convenient and organized storage solution for your frozen foods.

A bad bottom freezer basket assembly can occur due to wear and tear, accidental damage, or other factors. If you notice symptoms such as broken wires, a loose fit, or difficulty in sliding the basket, it may be time to replace it with a new one.

Symptoms of a bad bottom freezer basket assembly include:

• Broken wires
• Loose fit in the freezer compartment
• Difficulty in sliding the basket in and out

Improve your freezer storage and organization by replacing the faulty bottom freezer basket assembly with this genuine OEM part.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

The Basket Bottom Asm is an OEM part for GE refrigerators. This assembly is specifically designed to fit in the bottom freezer compartment, providing a convenient and organized storage solution for your frozen foods.

A bad bottom freezer basket assembly can occur due to wear and tear, accidental damage, or other factors. If you notice symptoms such as broken wires, a loose fit, or difficulty in sliding the basket, it may be time to replace it with a new one.

Symptoms of a bad bottom freezer basket assembly include:

• Broken wires
• Loose fit in the freezer compartment
• Difficulty in sliding the basket in and out

Improve your freezer storage and organization by replacing the faulty bottom freezer basket assembly with this genuine OEM part.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

This stopper divider holds and positions a refrigerator drawer or shelf divider to keep contents separated and prevent sliding. Durable molded plastic replaces a worn or broken stop to restore proper drawer alignment and function. What it does:

• Stops and anchors the refrigerator drawer/divider to prevent shifting during normal use
• Restores correct drawer travel and alignment when the original stop is cracked or missing
• Helps maintain organized storage by keeping divider panels in place
• Works with compatible OEM drawer and divider assemblies to ensure proper fit

• One stopper divider part as shown

• Basic hand tools may be required; inspect mounting area for debris or damaged clips before installing
• Align and snap or slide the stopper into the factory location until it seats securely
• Do not force parts into place; replace damaged clips or supports if the stopper will not seat properly
• Unplug or power off the appliance before inspecting interior components for safety

This right-hand slide bracket assembly replaces the damaged or worn guide that supports a refrigerator/freezer drawer, restoring smooth, stable opening and closing. It mounts on the cabinet side to guide the drawer slide. What it does:

• Provides the right-side support and track for a drawer slide to engage and move smoothly
• Prevents the drawer from binding, tilting, or falling out when opening or closing
• Restores proper alignment for even drawer operation
• Helps eliminate scraping, sticking, or noisy drawer movement

• Remove all contents from the drawer and open to access the bracket before starting
• Basic hand tools (screwdriver or nut driver) are typically required; keep screws and fasteners from the old bracket for reuse if undamaged
• Disconnect power or follow appliance-specific safety procedures before working near electrical components

This left-hand slide bracket assembly supports and guides a refrigerator drawer so it opens and closes smoothly. It replaces a worn or broken left slide bracket to restore proper drawer alignment and movement. What it does

• Mounts to the cabinet and holds the drawer glide/rail in place for stable operation
• Restores smooth drawer travel when the original bracket is cracked, bent, or broken
• Prevents drawer sagging, misalignment, or falling when loading items
• Works with the existing glide components to maintain proper drawer positioning

• One left-hand slide bracket assembly

• Disconnect power and remove drawer contents before starting work
• Remove the affected drawer and any trim to access the bracket; keep track of screws and clips
• Use appropriate hand tools; avoid forcing parts to prevent damage to surrounding components
• Inspect companion glide/rail parts and fasteners; replace damaged items for a complete repair

This silicon controlled rectifier (SCR) is a replacement power-control semiconductor used to regulate current in appliance power circuits, helping restore proper operation of heating and motor circuits that rely on solid-state switching. What it does:

• Acts as a switch to control and modulate electrical current in the appliance power path
• Enables regulated power delivery to heating elements or motor circuits when driven by the control board
• Commonly replaced when the appliance shows intermittent power, no heat, or erratic on/off behavior in the affected circuit
• Works as a direct replacement for the OEM SCR with identical mounting and electrical fit when specified by part number

• Disconnect power to the appliance before starting any repair to avoid shock or damage
• Observe basic ESD precautions when handling the SCR and avoid touching semiconductor leads

This rubber grommet cushions and protects small appliance wires, hoses, or components where they pass through panels or openings. It helps prevent chafing and vibration wear for quieter, longer-lasting operation. What it does:

• Cushions wiring or tubing where it passes through sheet metal to prevent rubbing and damage
• Reduces vibration noise from loose fittings or contact points
• Holds harnesses or hoses in position to maintain proper routing
• Helps keep openings sealed against dust and debris around routed components

• Disconnect appliance power (and water if applicable) before replacing parts
• Remove the original grommet and install the new grommet in the same orientation; ensure the wire/hose seats fully in the grommet
• Inspect surrounding wiring, hoses, and mounting holes for damage and replace if needed
• Use only the specified replacement grommet; do not modify with adhesives or solvents unless manufacturer guidance allows

The Top Freezer Basket Slide Bracket is an OEM replacement part for GE refrigerators. It is designed to securely hold the freezer basket slide in place, allowing for smooth and effortless movement when accessing items stored in the freezer. It provides stability and support to the basket, preventing it from tipping or falling out during use.

A bad top freezer basket slide bracket can occur due to regular wear and tear or accidental damage. If you notice symptoms such as a wobbly or unstable freezer basket, difficulty in sliding the basket in and out, or the basket not staying securely in place, it may indicate a need to replace this part.

Symptoms of a bad top freezer basket slide bracket include:

• Wobbly or unstable freezer basket
• Difficulty in sliding the basket in and out
• Basket not staying securely in place

Restore your freezer organization by replacing the faulty top freezer basket slide bracket with this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

The Refrigerator Slide Lower Freezer is an OEM replacement part for GE refrigerators. It is a sliding component designed to facilitate smooth and effortless access to the lower freezer compartment. This OEM part ensures that the lower freezer drawer can glide in and out seamlessly, allowing for convenient storage and retrieval of frozen items.

Symptoms of a bad Refrigerator Slide Lower Freezer include:

• Difficulty opening or closing the lower freezer drawer
• Freezer drawer catching or sticking during operation
• Noisy or grinding sounds when sliding the drawer
• Drawer not staying in position when opened or closed

Causes of a bad lower freezer slide can include wear and tear from repeated use, damage from mishandling or overloading, or issues with the slide mechanism itself. Over time, the slides may become worn, misaligned, or obstructed, leading to operational problems.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore refrigerator models.

This left-side lower freezer slide restores smooth drawer movement and proper alignment in the freezer compartment. It replaces a worn or damaged slide to help the drawer open and close reliably. What it does:

• Replaces the left lower freezer drawer slide that guides the drawer on its track
• Restores smooth, even sliding and prevents the drawer from sticking or binding
• Helps keep the drawer properly aligned so it opens and closes without catching
• Useful when the existing slide is bent, cracked, or worn and affects drawer operation

• Disconnect power and remove food from the drawer area before starting
• Typically installs onto the freezer cabinet and drawer track; basic hand tools may be required
• Align slide with factory mounting points and secure hardware; test drawer movement after installation

This refrigerator ice bucket assembly stores the ice made by your icemaker and delivers it when needed. Replacing a cracked or worn bin restores smooth ice storage and consistent ice delivery performance. What it does:

• Collects and holds ice in the freezer/ice compartment
• Interfaces with the drive/auger on dispenser-equipped models to move ice out of the bin
• Helps maintain proper ice flow and reduce jams or clumping
• Common symptoms: cracked/broken bin, bin won't seat or lock, ice not dispensing or intermittent dispense

• Includes 1 ice bucket assembly

• Unplug the refrigerator before servicing; work with dry hands
• Empty and remove the old bucket; retain any screws/clips used by your model
• Transfer any reusable parts from the old bin if required by your model
• Slide the new bin in fully so it seats and engages the drive; restore power and test after fresh ice is produced

The Icemaker Fill Cup is an OEM replacement part for GE refrigerators responsible for directing the water flow into the icemaker, allowing for the creation of ice cubes. It securely attaches to the icemaker, preventing any leaks or spills that could disrupt the ice production.  

A bad fill cup can occur due to several factors. Common causes include cracks, damage, or wear and tear over time. If you notice symptoms such as leaks around the icemaker, improper ice production, or water overflow, it may indicate a need to replace the fill cup.

Symptoms of a bad fill cup include:

• Leaks around the icemaker area
• Insufficient or inconsistent ice production
• Water overflow or spills

Restore your refrigerator's ice-making capabilities by replacing the faulty fill cup with this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

The Icemaker is an OEM component specifically designed for GE refrigerators. Located within the freezer compartment, the icemaker automatically produces batches of ice for convenient access.

Causes of a bad icemaker can include wear and tear of mechanical parts from years of producing ice. Mineral buildup may also clog components and impact performance over time.

Symptoms of a bad icemaker include:

• Failure to produce ice or very slow production  
• Ice cubes joining together in clumps or odd shapes
• Loud grinding sounds emanating from the assembly
• Leaks or water drips detected around the unit

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models. 

This left-side freezer holder slide secures and guides the freezer drawer for smooth opening and closing. Replacing a worn or broken slide restores proper drawer alignment and helps prevent sagging or sticking. What it does:

• Supports the freezer drawer on the left side and keeps it aligned during use
• Guides drawer movement for smooth opening and closing
• Replaces damaged, bent, or missing slides that cause binding or uneven drawer travel
• Helps prevent the drawer from sagging, slipping, or coming off its track

• Disconnect power before servicing to avoid electrical hazards
• Remove freezer contents and a drawer or panel as needed for access
• Compare the old slide to ensure correct left/right orientation before installing
• Use basic hand tools; do not force parts—replace any damaged mounting hardware

The Striker Light Switch is an OEM component specifically designed for GE refrigerators. Located on the refrigerator door, it controls interior lighting functions.

Causes of a bad switch can include wear from opening the door frequently or water damage over time.

Symptoms of a failed switch include: 

• Lights not turning on when the door is opened  
• Lights remain illuminated all the time even when closed
• Flickering or unresponsive lighting behavior

This switch utilizes a striker plate activation mechanism that triggers interior lights based on door position - open or closed. A replacement ensures lighting convenience and energy efficiency. 

This genuine OEM GE part restores dependable on/off lighting control through the normal door operation process. Compatible with additional brands including Hotpoint, RCA, or Kenmore models.

This ice maker feeler arm senses the ice level in the bin and controls when the icemaker starts and stops. Replacing a bent, missing, or stuck arm restores correct shutoff and helps prevent overfilling or no-ice conditions.

• Monitors the ice bucket level and raises/lowers to start or stop ice production
• Shuts the icemaker off when the bin is full; allows production when lowered
• Common symptoms: ice maker won't stop making ice/overflows, no ice when the arm is stuck up, loose or missing arm
• Restores proper on/off control of the icemaker cycle

• Disconnect power and turn off the water supply before servicing
• Remove the ice bin and, the icemaker assembly to access the arm
• Transfer any reusable hardware; seat the arm fully in its pivot points so it moves freely
• Restore power, lower the arm to the On position, and allow time for the icemaker to cycle

This housing wire is the replacement wiring housing used with the ice maker assembly in the freezer compartment. It protects and routes ice-maker wiring to help maintain reliable ice production and prevent wire chafing. What it does

• Protects and organizes ice maker wiring inside the freezer to prevent damage and shorts
• Helps maintain a secure connection between the ice maker and freezer harness
• Commonly replaced when wiring housing is cracked, torn, or allowing wire exposure
• Can resolve intermittent ice maker operation or electrical arcing caused by damaged wire insulation

• One housing wire assembly as shown

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Access may require removing the ice maker or freezer liner
• Handle wiring and connectors carefully to avoid damage; replace any worn connectors or clips