Freezer Wire, Harness, Power Cord

This power cord assembly supplies electrical power from the wall outlet to your refrigerator. Replace a cut, frayed, or overheated cord to restore safe, reliable operation and eliminate intermittent power loss caused by a damaged cord. What it does:

• Provides the electrical connection between the household outlet and the refrigerator's wiring
• Helps resolve no-power or intermittent power when the cord is moved
• Addresses visible damage such as cuts, cracks, fraying, or a melted/discolored plug
• Mitigates arcing, sparking, or a burning odor originating from the cord or plug area

• One power cord assembly

• Disconnect power by unplugging the unit or switching off the circuit breaker before servicing
• Pull the refrigerator forward for access; note the original cord routing and connections
• Install the new cord along the same path and secure any built-in strain relief; ensure the ground connection is properly seated
• Restore power and verify operation

This replacement power cord delivers household electricity from the outlet to your appliance. Installing a new cord restores safe, reliable power when the original is damaged, worn, or causing intermittent operation.

• Supplies AC power from a household outlet to the unit
• Common fix for no power, flickering lights, or power loss when the cord is moved
• Replaces cords with cuts, cracks, burn marks, or melted areas
• Restores a secure electrical connection for safe, consistent operation

• Unplug the appliance and verify the wall outlet is working before replacing parts
• Access the cord routing and internal connections; note wire positions and routing before removal
• Transfer and secure any strain relief/clamp; keep wiring clear of sharp edges and hot surfaces
• After installation, ensure the cord isn't pinched and the plug seats fully in the outlet

This replacement electrical wire restores a single conductor connection used in your appliance's wiring system, helping re-establish power or signal continuity where the original lead is damaged. What it does

• Replaces a single appliance electrical lead to restore lost connection or repair damaged insulation.
• Used to carry power or control signals between components.
• Common symptom: intermittent or no power to a component, visible frayed or broken wire.
• Matches original part function and routing; intended for direct replacement.

• One replacement electrical wire (single lead).

• Disconnect power to the appliance before starting any repairs to avoid shock.
• Verify wire routing and secure connections match the original; use proper wire connectors and insulation.
• If soldering or crimping is required, follow manufacturer guidelines and use proper tools.

This genuine OEM wiring harness routes power and signals between components to restore reliable electrical connections in the appliance. It replaces worn, damaged, or corroded harnesses to help bring components back to normal operation. What it does:

• Links motors, switches, sensors, or control boards so the appliance can receive power and communicate between parts
• Replaces frayed, burned, or broken wiring that can cause intermittent or no operation
• Helps stop electrical arcing or poor connections that may lead to component failure or safety trips
• Restores proper circuit continuity to resolve symptoms like no power to a motor, controls not responding, or intermittent cycles

• One wiring harness

• Disconnect power (unplug or shut off breaker) before starting any work
• Match connector shapes and wire colors; route harness away from moving parts and heat sources
• Secure with existing clips or ties; avoid pulling on individual wires when connecting

This main wiring harness connects the appliance's control components and power distribution, restoring electrical pathways so controls, sensors, and motors can operate correctly. Replace a damaged harness to regain reliable electrical continuity and signal routing. What it does

• Routes power and control signals between the appliance control board, switches, sensors, and motors.
• Restores electrical continuity when broken, cracked, or melted wires cause intermittent or no operation.
• Helps eliminate faults caused by shorted or corroded connector pins and damaged insulation.
• Supports normal operation of the user interface and protected components by keeping wiring organized and secured.

• One main wiring harness assembly as pictured.

• Disconnect power (unplug or switch off breaker) before starting any repair to avoid shock or equipment damage.
• Verify the harness matches the connector types and mounting points on your appliance before installation.
• Use proper strain relief and routing to avoid pinched wires; replace any damaged clips or grommets.

This main wiring harness routes power and signals between the appliance control board and major components to restore electrical connectivity and reliable operation. Use when controls or features lose power or respond intermittently. What it does:

• Carries power and control signals from the main control to motors, valves, sensors and other components
• Replaces damaged, pinched, or burnt wiring that can cause intermittent operation or feature failure
• Restores proper connector fit and circuit continuity between modules
• Helps eliminate electrical shorts and unreliable connections when the original harness is faulty

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Route harness along original clips and fasteners; avoid sharp edges and heat sources