Freezer Cap Or Cover

The Glass is an OEM part for Frigidaire refrigerators. This part is a replacement shelf or panel within the appliance. This high-quality, durable glass provides a stable and clean surface for storing food and beverages, optimizing the organization and capacity of your refrigerator. The transparent nature of the glass allows for easy visibility of the contents, making it simpler to keep track of your groceries and to clean up spills or messes.  

Causes of a bad glass can vary from accidental damage, such as dropping heavy items on the shelf, to normal wear and tear over time.

Symptoms of a bad refrigerator glass include:

• Cracks or chips in the glass
• Stains or discoloration that cannot be cleaned
• Sagging or bending under weight, indicating weakness

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This evaporator fan motor dust cap is an authentic OEM replacement part found on refrigerator and freezer fan motors. This dust cap prevents the fan motor bearing and housing from being damaged by dirt and debris. If the dust cap is cracked or broken, the fan may make loud squealing noises. If the dust cap is not removed and replaced, the fan could stop working and ultimately cause the refrigerator's temperature to be affected. To start, disconnect the power and water to the refrigerator. Remove food from the freezer so that the back panel of the freezer can be accessed to reach the fan. Remove the ice maker and set it outside the freezer. Disconnect the fan and take it out of the freezer to expose the fan's shaft and the dust cover. Pry the dust cover off and install the new one. Replace the fan and cover. Reconnect the wires and reinstall the icemaker. Put the food back in the freezer. Reconnect the power and water.The evaporator fan motor dust cap is a white plastic part that is sold individually. This dust cover is made for use in refrigerators manufactured by General Electric, Hotpoint, and Kenmore.

The Glass Shelf is an OEM part for Frigidaire refrigerators. This part provides a sturdy and transparent surface for organizing food items within the fridge.  

Causes of a bad glass shelf can include accidental dropping or mishandling, heavy loads causing cracks or breakage, or thermal stress from extreme temperature changes.  

Symptoms of a bad glass shelf include:

• Cracks or chips in the glass
• Sagging or instability when supporting items
• Difficulty in fitting the shelf properly into its designated slots
• Visible wear and tear on the edges or surface of the glass

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This replacement glass panel restores a smooth, sturdy surface to your refrigerator or freezer shelf/cover assembly, helping contain spills and safely support stored items so your food stays organized and accessible. What it does:

• Replaces cracked, missing, or stained shelf/cover glass to restore a flat storage surface
• Helps contain spills to prevent drips onto lower shelves or drawers
• Supports food items evenly to reduce tipping or wobbling
• Improves overall shelf stability and cleanliness

• 1 glass panel

• Unplug the appliance and wear cut-resistant gloves when handling glass
• Remove the shelf/cover assembly; note orientation before disassembly
• Carefully slide out the old glass, clean the frame/rails, and seat the new glass fully
• Ensure the panel is evenly supported on all sides before reloading items

This icemaker assembly replaces the automatic ice maker in your freezer. It restores dependable ice production by controlling the fill–freeze–eject cycle, providing a steady supply of properly sized cubes to the bin when operating correctly.

• Automates the fill, freeze, and harvest cycle to produce ice cubes and drop them into the bin
• Sends power to the water inlet valve during the fill portion of the cycle; stops production when the bin is full (shut-off arm, if equipped)
• Common symptoms of a failed icemaker include no ice production, slow or small cubes, cubes not ejecting, or leaking/overflowing from the icemaker area
• Replaces a worn or seized icemaker module to restore normal cube production

• Disconnect power and shut off the water supply before servicing
• Remove the ice bin for access; detach the old unit and disconnect its wire harness
• Mount the new assembly; ensure the fill tube is aligned and the shut-off arm moves freely
• Restore power and water; discard the first batch and allow up to 24 hours for production to normalize

A replacement corner cabinet trim that restores the finished edge on the appliance cabinet and hides gaps for a cleaner look. Helps maintain the cabinet appearance and prevents debris buildup at the corner. What it does:

• Replaces a cracked, broken, or missing corner trim piece to restore the cabinet edge
• Covers gaps where two cabinet panels meet to improve appearance
• Helps reduce dirt and moisture accumulation in the corner area
• Stops rattling or catching caused by a damaged trim

• Service is generally simple; remove any nearby shelving or panels for access
• Fastens with the factory clip or screw method used on the model—retain original hardware and check alignment before final fastening
• Disconnect power to the appliance if needed to access fasteners near electrical components
• Wear gloves to protect hands from sharp sheet-metal edges during installation

This top cover hinge secures the upper access cover on compatible refrigerators, keeping the cover aligned and stable for reliable operation and easy access during maintenance. It restores proper fit and prevents rattling or loose covers. What it does:

• Supports and fastens the refrigerator's top access cover to the cabinet
• Keeps the cover properly aligned to prevent gaps and vibration noise
• Restores secure cover movement after wear or damage to the original hinge
• Helps maintain a sealed fit so panels sit flush and access remains safe

• Disconnect power to the appliance before beginning any repair
• Installation typically requires basic hand tools (screwdriver, nut driver); retain original fasteners unless replacements are supplied
• Align the cover on the hinge before tightening screws; avoid over-torquing hardware

White.

This white hinge sleeve cap covers and protects the exposed hinge bushing/pin area, providing a clean, finished look while helping keep debris out of the hinge mechanism.

• Covers the hinge sleeve to improve appearance and protect the hinge area
• Helps prevent dirt and moisture from entering the hinge bushing
• Common failure signs include a missing/broken cap or a loose cap that won't stay in place
• May be used on door hinge locations where a sleeve/bushing is present

• Unplug the appliance or shut off power before starting
• Open the door and support it if working near a hinge
• Gently pry off the old cap; press the new cap firmly onto the hinge sleeve
• Do not force—align carefully to avoid cracking the cap

This corner cabinet trim replaces a damaged or missing corner finish piece on the appliance cabinet, restoring a clean edge and helping the door and adjacent panels fit correctly. It provides a cosmetically complete appearance. What it does:

• Covers and protects the cabinet corner for a finished look
• Helps maintain proper alignment and spacing at the cabinet corner
• Commonly replaced when cracked, chipped, broken, or missing
• Restores cosmetic appearance and helps prevent exposed sharp edges

• One corner cabinet trim piece

• Turn off and unplug the appliance before accessing trim or removing panels
• Trim may secure with clips, screws, or snap-fit tabs—inspect fasteners and retainers before removal
• Handle edges carefully; use appropriate tools to avoid scratching adjacent surfaces

This hole cover seals an access/opening in the refrigerator evaporator housing to help maintain proper airflow and prevent moisture or frost from entering the cabinet. A simple replacement that restores the evaporator enclosure's intended seal. What it does:

• Seals an opening in the evaporator housing to reduce air leaks and unwanted moisture entry
• Helps prevent excessive frost or ice buildup near the evaporator area
• Supports consistent cooling by keeping the evaporator cover intact
• Can stop interior water or debris from entering the evaporator cavity

• Disconnect power to the appliance before starting any repair
• Remove the evaporator cover or access panel as required to reach the opening
• Press or snap the cover into place until it seats securely; no special tools typically required
• If the cover is brittle or damaged, inspect surrounding mounting surfaces and replace as needed

This top lock cover is a direct-fit replacement housing that protects the lock mechanism and restores a finished appearance to the appliance. It keeps internal components shielded from dust and wear for reliable operation. What it does:

• Covers and protects the top lock assembly, preventing debris and accidental contact
• Restores the original appearance when the factory cover is cracked, faded, or missing
• Helps maintain proper alignment and operation of the lock by keeping components enclosed
• Common symptom: visible crack, broken tabs, or missing cover exposing the lock mechanism

• One top lock cover

• Disconnect power to the appliance before starting any repair
• Typically installs with a few screws or snap-fit tabs; remove trim as needed to access the lock area
• Handle plastic tabs carefully to avoid breakage during removal and installation

This hinge-side door stop helps limit door travel and protect the hinge assembly from over-rotation for a secure, consistent door movement. Replaces a worn or broken hinge-side stopper to restore proper door alignment and operation. What it does:

• Acts as the stop/breaker on the hinge side to prevent the door from swinging past its intended range
• Helps reduce stress and wear on the hinge and door seal caused by over-rotation
• Commonly replaced when the door catches, over-rotates, or the hinge feels loose
• Works with the hinge assembly to keep door movement smooth and predictable

• Disconnect power to the appliance before starting any repair
• Remove the door or access hinge per your model's service instructions to reach the stopper
• Inspect adjacent hinge hardware and fasteners; replace any stripped or damaged parts
• Use proper hand tools and follow manufacturer torque and alignment guidance