Freezer Leg Or Foot

The Adjustable Foot is an OEM part for Frigidaire dryers. This part is located at the bottom of the dryer and allows you to level it, ensuring stability and proper operation. 

Causes of a bad adjustable foot can include regular wear and tear, damage from moving the appliance, or breaking due to excessive weight or stress.  

Symptoms of a bad adjustable foot include:

• The dryer wobbling or tilting
• Difficulty in adjusting the height of the foot
• Visible damage or deformation of the foot
• Unusual noises or vibrations during operation

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This replacement cab roller restores smooth movement and support for the appliance cabinet/door component, helping reduce noise and prevent binding from worn or damaged rollers. What it does

• Supports and guides the cabinet/door or sliding assembly for proper alignment
• Helps maintain smooth, quiet operation during opening/closing or movement
• Worn or broken rollers can cause sticking, scraping, or unusual noise
• Replacing the roller resolves common movement and alignment symptoms

• One roller

• Disconnect power and water before starting any repair
• Remove the affected panel or door per the appliance service instructions to access the roller
• Inspect mounting bracket and tracks for wear or damage; replace additional damaged parts as needed
• Use basic hand tools; avoid forcing components to prevent damage

This replacement leveling foot stabilizes and supports the appliance so it sits level and steady on the floor. Restores proper alignment for doors and drawers and reduces wobble or rocking. What it does:

• Replaces a worn or damaged support foot to restore proper appliance height and balance
• Helps stop rocking, tipping, or uneven operation caused by an unstable base
• Can improve door alignment and sealing by returning the appliance to a level position
• Quietly supports normal appliance movement without introducing vibration

• Disconnect power and empty or secure contents before adjusting or replacing feet
• Support the appliance with a block or helper to prevent tipping while swapping the foot
• Thread or snap into place per the appliance's mounting design; tighten by hand or with appropriate tool
• Re-level the appliance after installation and verify doors/drawers open and close smoothly

This axle wheel is a replacement drum support component that helps the dryer drum roll smoothly and quietly. Replacing a worn axle wheel restores proper drum alignment and reduces noise or binding during operation. What it does:

• Supports and centers the dryer drum on its axle so the drum turns freely
• Replaces worn or damaged wheel surfaces that cause squeaks, grinding, or rubbing
• Helps prevent drum wobble and uneven wear on the drum seal or rollers
• Works as part of the drum support system to maintain smooth rotation

• One axle wheel

• Disconnect power before starting and work on a cool, empty dryer
• Removing the dryer front or drum may be required to access and replace the wheel
• Inspect other drum support components (rollers, glides, bearings) and replace as needed

This adjustable leveling leg replaces a worn or damaged refrigerator foot to restore stable, level support and smooth door operation. Simple height adjustment helps eliminate rocking and keeps the appliance sitting evenly on uneven floors. What it does:

• Supports the appliance weight and lets you fine-tune height for proper leveling
• Compensates for uneven floors to reduce rocking and wobble
• Helps doors seal and align correctly by allowing height adjustment
• Reduces vibration-related noise when the cabinet sits evenly

• One adjustable leveling leg

• Use gloves and eye protection; unplug the appliance and remove food or shelves near the work area before starting
• Tilt or raise the appliance slightly as recommended by the manufacturer to access the leveling leg; support the cabinet securely
• Turn the leg to raise or lower the appliance; check level and door operation, then recheck after the appliance settles
• If the leg threads or mounting hardware are damaged, replace all affected components before returning the appliance to service

This castor kit replaces worn or damaged cabinet casters so the appliance rolls smoothly for cleaning and service access. It restores mobility to the appliance base and prevents catching or dragging during movement. What it does:

• Provides rolling support for the appliance base so the unit can be moved easily for cleaning or servicing
• Replaces cracked, seized, or missing casters that cause dragging or uneven movement
• Helps protect the cabinet and floor by allowing controlled rolling instead of scraping
• Matches OEM fit and mounting points for straightforward replacement where specified

• Unplug the appliance and empty or secure loose contents before starting
• Support the appliance safely to prevent tipping when removing or installing casters
• Use appropriate hand tools; avoid overtightening fasteners that can bind the caster

This front foot replaces a worn or missing stabilizer that supports and levels the appliance at the front. Restores stable, even positioning to reduce rocking, scraping, and uneven operation. What it does

• Supports the front of the appliance to maintain proper leveling and balance.
• Helps stop rocking, tipping, or shifting during cycles.
• Reduces scraping or rubbing against cabinets or flooring when in use.
• Restores correct alignment for doors and drawers that hang or don't close evenly.

• One front foot/stabilizer.

• Disconnect power and water (if applicable) and use safe lifting/support methods before accessing the foot.
• Back off or remove the old foot, then install and hand-tighten the replacement; adjust height as needed for level.
• Re-check appliance level and stability after installation; avoid over-tightening to prevent damage.