Frigidaire Freezer Parts

This inner door panel restores the interior structure and appearance of an oven door. It provides a replacement inner surface that supports door glass and insulation for safe, reliable operation. What it does:

• Replaces a cracked, dented, or warped inner oven door panel to restore proper fit and finish
• Helps secure and protect the door glass and internal insulation
• Eliminates rattling or loose interior door components caused by bent or damaged panels
• Improves the door's sealed fit when combined with intact outer glass and seals

• Power off the appliance and allow the oven to cool completely before starting any repair
• Door disassembly and reassembly are often required; keep track of fasteners and use a work surface to protect glass
• Wear gloves and eye protection—panel edges and broken glass can be sharp
• Follow the OEM service manual for correct removal/replacement procedures and torque specifications

This inner door panel replaces the plastic liner on the inside of a refrigerator or freezer door, restoring a clean interior surface and providing mounting points for bins and shelves. It helps stop air leaks and improves door appearance. What it does:

• Replaces a cracked, warped, or damaged door liner to restore structural integrity and appearance.
• Provides mounting surfaces for door bins, shelves, and gaskets so accessories fit and seal properly.
• Helps maintain proper door sealing by restoring the inner surface and alignment.
• Reduces the risk of moisture intrusion behind the liner that can cause odors or mold.

• High-level task: usually removes and installs from inside the door after removing door trim and hardware; follow manufacturer instructions.
• Use correct replacement fasteners and gaskets; do not overtighten screws to avoid cracking the liner.
• Work with the door supported to prevent dropping or bending; two-person assistance may be helpful for larger doors.
• Disconnect power if required by the manufacturer before removing door components to avoid electrical hazards.

This replacement electrical wire restores a single conductor connection used in your appliance's wiring system, helping re-establish power or signal continuity where the original lead is damaged. What it does

• Replaces a single appliance electrical lead to restore lost connection or repair damaged insulation.
• Used to carry power or control signals between components.
• Common symptom: intermittent or no power to a component, visible frayed or broken wire.
• Matches original part function and routing; intended for direct replacement.

• One replacement electrical wire (single lead).

• Disconnect power to the appliance before starting any repairs to avoid shock.
• Verify wire routing and secure connections match the original; use proper wire connectors and insulation.
• If soldering or crimping is required, follow manufacturer guidelines and use proper tools.

This small plastic clip secures the dishwasher drain hose to the pump assembly or discharge fitting, keeping the hose in place and helping prevent leaks or disconnection during operation. What it does:

• Holds the drain hose firmly to the pump or outlet fitting to maintain a watertight connection
• Prevents the hose from slipping free during drain cycles
• Helps stop water leaks and washing chamber flooding caused by a loose hose
• Useful when replacing a cracked or broken retaining clip

• One drain hose retaining clip

• Disconnect power and water supply before accessing the dishwasher lower access area
• Remove the access panel or kickplate to reach the drain hose and pump connection
• Use pliers or a flat tool to remove the old clip and snap the new clip over the hose/fitting until fully seated
• After installation, run a short drain cycle and inspect for leaks; re-secure if necessary

This inner door panel replaces a damaged or worn interior door surface to restore proper bin support and the refrigerator's finished appearance. It provides a stable mounting surface for door bins and internal hardware. What it does

• Replaces a cracked, warped, or damaged inner door surface that can let door bins sit unevenly or rattle.
• Provides the structural mounting area for door bins, shelves, and hardware.
• Restores the door's finished interior appearance and helps maintain proper fitment of interior components.
• Helps prevent moisture and debris from entering the inner door cavity when intact.

• Disconnect power to the appliance before starting any repair.
• Remove door-mounted items (bins, shelves, gasket, and trim) and retain all fasteners for reassembly.
• Handle the panel carefully to avoid cracking; support the door if removing it from the cabinet.

This adhesive-backed plastic mounting clip secures wires, small hoses, or components inside appliances to reduce movement and rattling. Its low-profile design helps keep internal parts organized for quieter, safer operation. What it does:

• Holds wiring harnesses, sensor leads, or small tubing in place to prevent chafing and noise
• Reduces vibration-related contact that can cause intermittent electrical or sensor issues
• Provides a simple, non-invasive mounting point without drilling or fasteners
• Adhesive backing allows quick placement in tight or hard-to-reach areas

• Clean and dry mounting surface; remove backing and press clip firmly for full adhesion
• Allow adhesive to set per ambient temperature (avoid stress on clip during initial cure)
• Disconnect power before installing
• Replace any brittle or damaged surrounding insulation or wire loom as needed