Frigidaire Freezer Parts

This slide basket is a direct-fit replacement that restores smooth slide-out access and secure storage for a refrigerator drawer. It helps keep foods organized and prevents items from shifting or falling when you open the drawer. What it does:

• Provides a slide-out basket for easy access to refrigerated or frozen items.
• Keeps stored items contained and organized on a removable platform.
• Replaces cracked, warped or damaged baskets that cause sticking, catching or uneven sliding.
• Helps prevent items from falling when pulling the drawer open.
• Works with the drawer's slide/track system to maintain alignment and function.

• Disconnect power to the appliance before starting any service.
• Remove food and lower shelves or drawers to access the basket; follow your owner's manual for removal steps.
• Inspect drawer slides and rails for damage before installing the new basket; align slides and test for smooth operation.

Lower basket organizes items in the bottom of your freezer. Replace a bent, broken, or missing basket to restore tidy storage and easier access to frozen food.

This is a compressor start relay that helps the compressor motor start up by providing the initial surge of power needed. It is a small device that typically mounts directly onto the compressor. Replace this part if the compressor fails to start, runs intermittently, or if you hear repeated clicking sounds coming from the back of the unit.

Freezer won't shut off or stop cooling? This temperature control thermostat cycles the compressor on and off to maintain set temps. DIY repair.

Fix a clicking compressor or refrigerator that won't cool. This start relay and overload assembly restores compressor startup. DIY repair in 10-15 minutes.

Replacement slide for freezer wire baskets. Attaches to basket bottom for smooth gliding along tracks. Replace when broken, cracked, or missing to restore alignment.

Secures panels, covers, or harnesses in place during operation. Replace if bent, broken, or missing to restore a tight fit and eliminate rattling.

This left end cap secures the end of a dishwasher rack door assembly, helping keep the rack stable and rollers aligned for smooth operation. It replaces a worn or broken cap to restore proper rack function and fit. What it does

• Covers and protects the outer end of the rack door, preventing exposed edges.
• Holds rollers or hinges in place so the rack slides smoothly.
• Helps keep the rack aligned to prevent catching or uneven movement.
• Common symptom: cracked, missing, or loose end cap causing rack wobble or noisy operation.

• Always disconnect power to the appliance before beginning repairs.
• Usually installs by snapping into place or fastening with the original screws; use basic hand tools.
• Inspect adjacent rollers and mounting hardware while replacing the cap.
• If fit feels tight, avoid forcing parts—verify orientation before final installation.

This bottom hinge replaces the lower door pivot on compatible Frigidaire refrigerators to restore proper door alignment and smooth opening. It provides a secure pivot point to help maintain an even close and consistent seal. What it does:

• Supports and pivots the lower edge of the refrigerator door for smooth opening and closing.
• Helps maintain correct door alignment so the gasket seals evenly.
• Common replacement for doors that sag, bind, or do not close evenly.
• Works with the factory mounting hardware and hinge locations on compatible models.

• Disconnect power and remove food and loose items from the door before starting.
• Always support the door while removing or installing the hinge to prevent injury or damage.
• Use appropriate hand tools and avoid overtightening fasteners; check door alignment after installation.
• Refer to your model's service manual or official parts diagram for model-specific steps and torque specs.

This compressor overload is a thermal/protective device that helps prevent compressor damage by cutting power when the motor overheats or draws excessive current. It restores normal operation once conditions return to safe levels. What it does:

• Protects the refrigerator compressor from overheating and electrical overloads
• Works with the compressor start relay to help the motor start and run properly
• Common symptom linkage: replaces a failed overload when the compressor hums but won't start
• Stops compressor cycling or prevents repeated trips that cause cooling loss

• One compressor overload (single piece as shown)

• Disconnect all power before replacing to avoid shock or injury
• Handle terminals carefully and reconnect matching terminal positions
• Replace only with the same part number or equivalent
• If compressor still won't start after replacing the overload, check the start relay and compressor condition.

Fix ice buildup and poor cooling caused by a faulty evaporator defrost heater. This heater melts frost during defrost cycles to restore proper airflow.

This is a small air baffle breather valve that helps equalize air pressure between the interior compartment and the outside environment. It allows air to pass through while helping maintain proper temperature regulation. Replace this valve if you notice excessive frost buildup, difficulty opening the door shortly after closing it, or unusual air pressure issues inside the unit.

Fix a refrigerator that won't cool or start. This compressor start relay helps your compressor run reliably and prevents clicking sounds. Easy DIY repair.

Rubber mounting grommet that cushions and isolates the compressor from the chassis. Replace if cracked, worn, or missing to restore proper support.

Replaces the inner door panel on your refrigerator or freezer door. Restores mounting points for bins and shelves. Order when cracked, warped, or damaged.

Color: White