Frigidaire Range / Cooktop / Oven Parts

The glue behind the keypad loosened and the keypad slowly began slipping down out of place over several months. Finally, because of the movement, it warped which resulted in one of the keys being stuck. That is what gave the F12 error code. The fix was easy. I removed the control panel and then peeled off the keypad. The keypad itself then has two layers (1), the flexible circuit panel, and (2) the outward facing display. I separated the display from the circuit panel and put the new one... Read more

Replaced the oven heating element Read more

Repair man said that the part alone would cost more than $300.00. I checked it out on YouTube and saw that the actual replacement was an easy task. I contacted appliancepartspros.com and spoke to Wendy, who sorted me out with the correct part which arrived in two days ($115.00). It took me less than 15 minutes to replace the part, no more leak. Thanks appliancepartspros.com and Wendy for your cost effective and speedy service. Read more

Ordered new Ignitor / Orifice and screws Mike was a great resource, he helped me thru the project. Read more

I replaced the large surface element first before examining the switch. In hindsight I probably only need to replace the large surface switch. Once I open the back of the control area of the stove the blacked switch and wire made in obvious that the trouble was in the connection and switch. Luckily, I had a new contact to rewire the wiring as the old was burnt badly. After cutting it out and connecting a new one and replacing the switch the problem was fixed. Read more

Had to pull double oven and range top out from wall which involved removing the upper kitchen cabinet. Took the sheet metal off the back and had the socket swapped out in a couple of minutes. My old oven works like a charm! Read more

Removing was easy. Pull out the ends of the seal, the ends aren't locked in. Then, pull up on each retaining clip. Each clip is held in with spring tension. Reinstallation was easy too. Start on one end, Twist frayed end into cone-like shape and insert into one of the holes for the seal. Push in with a skewer/screwdriver. Insert first clip into the first hole. Go around in a linear fashion, inserting each clip into each hole. After the last clip is pushed in, twist the end of the frayed end... Read more

Removed the bottom tin work in the oven and removed the burner tube. Tried to remove the igniter bracket but the screws were too tight for the Phillips head and couldn't get vice grips to clamp on the head, so I bent the bracket enough to remove and replace the igniter. Then reassembled. I give AppliancePros.com a 5 star rating. Site was easy to use, the part was delivered in under 2 days, and it was the correct part packaged carefully so the igniter was protected from breaking. Read more

• Element will not heat

Replaced infinite switch on large burners and just went ahead and replaced the infinite switch on the small burners while I had it apart and installed all new surface elements as well...parts were shipped the next day and I received them within 2 days... Read more

Ordered the dual element,only took 1 day for delivery,replaced element in about 15 min.and we're back in business Thanks Read more

Turns out these wall ovens have a pretty common problem, the baking element relay on the back of the control board solder joint fails. We have had this happen on several units recently as we manage several apt complexes. So it was not the baking element at all, just faulty solder joints or something makes the baking element relay lose its solder connection. Read more

Replaced Oven Control Board. I already had removed the old part when I ordered the replacement. Part showed up in 48 hours. It took me about two minutes to install the new part. Tested to make sure it worked, then another 30 seconds to screw the back panel of the stove on. Read more

Ordered on Wed, received on Fri. Took less than 5 minutes to replace all 4. No tools needed. Read more

I had to order the glass, frame, and cap that the handle attaches to. I just had to put in about 6 screws, it was very simple. Read more

I ordered an element one day it was there the next day, that was quick. It fit perfectly in place Read more

Found the parts I needed ordered them from your site Received them and installed in a few minuets and was done Read more