Frigidaire Range Panel Parts

The Oven Bottom Panel is an OEM component for Frigidaire oven models. Located on the base of the oven interior, this metal panel provides structure and support. 

Causes of a bad oven bottom panel include warping or damage due to exposure to high heat over time. Small nicks or cuts could allow heat to escape and reduce the oven's efficiency. Intentional or accidental impact during cleaning can also weaken the material.

Symptoms of a bad oven bottom panel include:

• Uneven or inefficient heat distribution within the oven
• Visible warping or damage to the panel surface
• Reduced heat retention leading to longer cook times
• Potential safety hazards if the metal is weakened

This OEM Frigidaire part is also compatible with some Kenmore models. 

This lower drawer replaces a damaged or missing bottom drawer on your range, restoring smooth slide action and a flush, finished look so the lower compartment operates correctly and the appliance is complete again.

• Forms the pull-out compartment beneath the oven for convenient access
• Interfaces with the drawer slides to open and close smoothly
• Restores proper alignment and full closure at the base of the range
• Typical symptoms: drawer jams, falls off tracks, sits unevenly, or is bent/dented

• Disconnect power and shut off gas; allow the range to cool before servicing
• Pull the old drawer out and lift to disengage from the slides; transfer any reusable parts as needed
• Set the new drawer onto both slides evenly and test for smooth travel and full closure
• If the drawer doesn't seat flush, re-check slide engagement and appliance leveling

This control panel replaces a worn, cracked, or cosmetically damaged console surface and restores clear button markings and access to controls. Fits the factory console opening and preserves the appliance's original look. What it does

• Provides the visible console surface that houses the control buttons and display
• Replaces cracked, chipped, or faded panels that make controls hard to read or use
• Restores a clean appearance and correct button/overlay alignment
• Helps prevent dirt and moisture from reaching the internal controls

• Disconnect power to the appliance before starting any work
• Handle the panel carefully to avoid scratching or bending during installation
• Installation typically requires removing console screws and any trim pieces; keep fasteners organized

This replacement panel restores your appliance's finished look and helps protect internal components. Replacing a cracked or loose panel eliminates gaps and rattles while keeping nearby trims or controls secured and aligned. What it does:

• Covers and shields internal areas, providing a clean, finished exterior
• Helps retain and align adjacent parts
• Restores proper fit when the original is cracked, warped, or discolored
• Common symptoms: broken mounting tabs, won't stay attached, vibration or rattling, visible gaps

• 1 panel

• Disconnect power to the appliance before servicing
• Wear cut-resistant gloves; edges can be sharp
• Retain and transfer any screws, clips, or badges from the original panel
• Align tabs/holes and secure fasteners evenly—do not overtighten

This control panel is the exterior trim that houses and protects the oven/range user interface and display, restoring a clean, functional front for the appliance. It keeps buttons and indicators secure and visible for reliable operation. What it does:

• Covers and protects the appliance control buttons, touchpad, and display from spills and damage
• Provides the visible interface for selecting oven functions and viewing status
• Restores a finished appearance to a damaged, cracked, or worn control area
• Helps ensure buttons and indicators align properly for correct operation

• One control panel

• Disconnect power to the appliance before beginning any repair to avoid shock or injury
• Some models require removing screws or snap clips and gently lifting the old panel from the console
• Handle the panel carefully to avoid scratching the visible finish or bending mounting tabs
• If the panel attaches to electronic components, take care not to damage ribbon cables or connectors; take care not to damage ribbon cables or connectors.

This replacement cabinet frame restores the appliance's front trim for a clean, finished appearance and proper panel alignment. It helps keep edges covered and maintains the door/cabinet fit. What it does:

• Provides the front trim/frame that supports and aligns the appliance cabinet or door panels
• Covers exposed edges for a finished look and helps reduce drafts or light gaps
• Helps eliminate rattling or misalignment caused by a damaged or warped frame
• Matches OEM fit to replace a cracked, bent, or cosmetically damaged frame

• Disconnect power (and water for appliances with water) before beginning any work
• Basic hand tools typically needed; retain all fasteners from the original part for reassembly
• Handle carefully to avoid scratching the finish; check fit before tightening fasteners

This replacement refrigerator cabinet liner restores the appliance's interior surface, helping contain spills and support shelves/drawers for reliable storage. Fits specific Frigidaire models; use the part number on your unit. What it does:

• Replaces cracked, warped or damaged interior surface that can allow moisture, odors, and debris to collect
• Provides the finished interior surface that supports shelf and bin mounting points
• Helps maintain a clean, easy-to-wipe interior and prevents insulation exposure
• Reduces the risk of leaks by restoring the proper fit and seals where the liner meets doors and gaskets

• One refrigerator cabinet liner as shown

• Disconnect power and empty the refrigerator before starting; follow manufacturer safety guidance
• Installation generally requires removing shelves, drawers and trim; small fasteners or clips may secure the liner
• Avoid sharp tools to prevent damage; inspect surrounding seals and hardware while replacing the liner

This interior refrigerator liner provides the finished, easy-to-clean surface for the fresh food compartment and helps support shelves and bins. It restores the cabinet interior to factory condition for proper fit and appearance. What it does:

• Replaces a cracked, warped, or stained interior cabinet surface.
• Provides a smooth, washable surface that helps keep food area sanitary.
• Supports mounted shelves, drawers, and trim pieces in the compartment.
• Restores proper alignment and sealing where the liner mates to refrigerator components.

• Disconnect power and remove all food and removable shelves/bins before starting.
• Typical installation requires removal of trim and fasteners; keep hardware accessible for reassembly.
• Handle carefully to avoid scratching the finished surface and to prevent injury from sharp edges.

This oven door glass assembly replaces damaged or cracked door glass to restore a clear viewing window and help keep the oven cavity sealed. It's a direct-fit replacement for affected Frigidaire oven doors. What it does:

• Replaces cracked, chipped or broken oven door glass to restore safe, visible operation.
• Lets you monitor cooking without opening the door to prevent heat loss from frequent door openings.
• Helps the door maintain its sealed barrier for more consistent oven performance.
• Matches OEM form for straightforward fit and alignment when installed correctly.

• Disconnect power (and gas if applicable) before starting; handle glass with thick gloves and eye protection.
• Installation may require removing the oven door and several screws—keep parts organized and follow OEM instructions.
• Inspect door seals and mounting hardware while replacing the glass; replace any damaged components.

This glass assembly replaces a damaged or broken oven door viewing panel to restore visibility and help contain heat for safe cooking. It fits into the oven door frame and provides a clear window for monitoring food. What it does:

• Replaces cracked, shattered, or scratched oven door glass to restore a clear viewing window
• Helps maintain proper heat containment and oven performance when installed correctly
• Eliminates rattling or movement caused by loose or broken glass
• Reduces risk of cuts or glass fragments inside the oven when replacing damaged glass

• One glass assembly as shown

• Handle with heavy-duty gloves and eye protection; glass can break unexpectedly
• Follow the oven manufacturer's door-disassembly instructions; some installs require removing the door and brackets
• Inspect door seals and mounting hardware and replace any damaged components for a secure fit