Frigidaire Range Insulation, Sound Dampening Parts

This insulation panel fits inside the refrigerator cabinet to help maintain interior temperatures and reduce heat transfer to the outer shell, supporting more consistent cooling and helping limit frost buildup. What it does:

• Forms a thermal barrier between the interior liner and outer cabinet to help hold cold air inside.
• Helps reduce frost and moisture buildup around the liner when intact.
• Worn, torn, or missing insulation can contribute to longer run times, uneven cooling, or more frequent defrost cycles.
• Replaces damaged insulation to restore proper temperature retention and improve appliance efficiency.

• Always disconnect power to the appliance before starting any repair.
• Panel may be secured with clips, adhesive, or foam sealant; remove and install carefully to avoid damaging the liner.
• Inspect surrounding seals, gaskets, and fasteners while accessing the cavity; replace any damaged components.

This oven insulation surrounds the oven cavity to retain heat and protect nearby components and cabinetry. Replacing a burnt or deteriorated insulation blanket restores temperature stability and helps keep exterior surfaces cooler on your range during cooking.

• Minimizes heat loss for more consistent baking temperatures
• Shields wiring, controls, and adjacent cabinets from excessive heat
• Damaged insulation can cause long preheat times or trouble maintaining set temperature
• Exterior panels or control area may feel unusually hot, or a burnt odor may persist after spills

• Disconnect power at the breaker; shut off gas
• Allow the appliance to cool completely before service
• Access typically requires pulling the range and removing outer panels; note original routing and retainers for reassembly
• Handle insulation carefully; wear gloves, eye protection, and a dust mask to avoid irritation from fibers

This thermal insulation replaces the heat-retaining blanket used around the oven cabinet. Restoring the insulation helps the appliance maintain temperature and protects surrounding components and cabinetry from excessive heat. What it does:

• Reduces heat loss from the oven cavity to improve temperature stability
• Helps the unit preheat and recover more efficiently
• Limits heat transfer to side panels and the control area
• Reduces persistent burning odors if old insulation was contaminated by spills

• 1 insulation piece

• Disconnect power and allow the appliance to cool completely before service
• If applicable, shut off gas supply before moving a range
• Wear gloves, long sleeves, and eye protection; fiberglass can irritate skin and eyes
• Note factory placement before removal; handle gently to maintain loft, avoid compressing, and ensure no wires are pinched when reassembling

Oven wrapper insulation that surrounds the oven cavity to retain heat, protect outer panels, and improve temperature stability—helping reduce exterior heat and support more consistent cooking results. What it does:

• Wraps the oven cavity to reduce heat transfer to the cabinet and outer panels.
• Helps maintain internal oven temperatures for more even baking and cooking.
• Damaged or missing insulation can allow outer surfaces to run hot, cause longer preheat times, or contribute to uneven cooking.
• Reduces the risk of heat-related damage to surrounding cabinetry and components.

• Disconnect power and allow the appliance to cool completely before servicing.
• Handle insulation with care; avoid compressing or tearing the material during installation.
• Reinstall using original mounting clips or hardware; verify proper fit around the oven cavity before replacing panels.

This insulation panel fits inside the refrigerator cabinet to help maintain consistent temperatures and reduce heat transfer. It preserves cooling efficiency and helps minimize frost and condensation when the appliance is operating properly. What it does:

• Provides thermal barrier between the cabinet and outer shell to help maintain internal temperature
• Helps reduce frost buildup and interior condensation when sealing and cooling systems are functioning
• Can improve energy efficiency by minimizing unwanted heat gain
• Dampens vibration and can reduce operating noise from the compressor area

• Disconnect power to the appliance before starting any repair to avoid electric shock
• Handle insulation carefully—avoid compressing or tearing the material to retain thermal performance
• Remove interior panels or shelving as needed to access the installation area; keep track of fasteners
• If the original insulation is damaged or contaminated, replace it and check nearby seals and gaskets for proper fit

This foam cabinet insulation panel helps reduce heat transfer and stabilizes internal temperatures, improving cooling performance and efficiency in the refrigerator cabinet. It replaces torn or missing insulation to help maintain consistent operation. What it does:

• Replaces damaged or missing cabinet foam insulation to reduce temperature fluctuations
• Helps limit frost buildup and uneven cooling caused by gaps in the cabinet
• Supports overall refrigerator efficiency by reducing heat gain from surrounding air
• Covers interior cabinet cavities where insulation is required for proper operation

• One foam cabinet insulation panel

• Disconnect power to the appliance before starting any repair
• Remove shelves and access panels for a clear work area; adhesive or clips may secure the insulation
• Press insulation into place, replacing any fasteners or adhesive strips as needed

This heat-resistant insulation helps contain oven heat and shield surrounding components. Replacing worn insulation supports faster, more consistent preheating, steadier baking temperatures, and cooler exterior panels for safer, more efficient operation. What it does:

• Wraps/lines the oven cavity or panels to reduce heat loss and protect nearby wiring and controls
• Helps the oven preheat efficiently and maintain consistent cooking temperatures
• Limits heat transfer to exterior panels and surrounding cabinetry
• Common signs of failure: longer preheat times, temperature swings, unusually hot sides/back, or insulation that is burnt, brittle, soaked, or missing

• 1 insulation piece

• Disconnect power and, if applicable, shut off gas before servicing
• Access typically requires removing rear/side panels or sliding the unit out; take photos to aid reassembly
• Wear gloves and a dust mask; handle gently—do not compress insulation and keep clear of sensors/wiring
• Re-secure with original clips/tape, reinstall panels, then test preheat and check for abnormal exterior heat

This oven back insulation panel fits behind the oven cavity to help contain heat and protect rear components. It replaces missing or damaged insulation to help restore normal oven heating behavior and reduce heat transfer to surrounding areas. What it does:

• Limits heat loss from the rear of the oven cavity to help maintain cooking temperature
• Helps reduce excessive heat transfer to rear components and cabinetry
• Use when insulation is torn, compressed, burned, or when the oven takes noticeably longer to preheat
• Helps prevent heat-related damage to wiring, electronics, and nearby parts

• Disconnect power to the appliance before starting any repair
• Access may require pulling the range/oven away from the wall and removing a rear access panel
• Wear gloves and a dust mask when handling old insulation; avoid compressing or tearing the replacement
• Follow OEM instructions for securing insulation with the original clips/adhesive or fasteners

This molded cabinet liner insulation reduces heat transfer around the refrigerator cavity to help maintain steady temperatures and improve cooling efficiency. Designed to replace worn or damaged insulation that can allow frost buildup or increased run time. What it does

• Fills the airspace between the outer cabinet and inner liner to slow heat gain
• Helps the cooling system maintain consistent internal temperatures
• Can reduce frost accumulation caused by damaged or missing insulation
• Restores the original thermal barrier after repair or after removing interior components

• One pre-formed cabinet liner insulation piece

• Disconnect power to the appliance before starting any repair
• Remove shelves, panels, and fasteners as needed to access the insulation cavity
• Handle gently to avoid compressing or tearing the material; fit into existing channels or adhesive points
• If adhesive is required, use manufacturer-recommended high-temperature adhesive or fasteners

This cabinet insulation helps reduce heat transfer inside the refrigerator, supporting stable temperatures and efficient cooling. Replacing damaged or missing insulation can improve temperature control and reduce frost buildup. What it does:

• Fills gaps between the cabinet and liner to slow heat transfer and maintain internal cold
• Helps the appliance reach and hold set temperatures more consistently
• Reduces condensation and excess frost on interior surfaces
• Can improve compressor run-time and overall energy efficiency when intact

• Disconnect power before starting
• Remove food and shelving from the compartment before accessing the insulation
• Handle insulation carefully to avoid tearing; secure per manufacturer routing and adhesive points
• Dispose of old insulation per local regulations