Need Help?
Call or text
Oven won't light even with glowing igniter? Safety valve controls gas flow to burner. Moderately easy repair with gas line disconnect required.
My tenant thought that the oven safety valve was bad, but after some research, I found that the transfer of heat from the igniter had to be sufficient enough to cause the valve to open.Your agent confirmed this and reassured me that even if the igniter was glowing, there was a 99% chance that it wasn't getting hot enough. I ordered the igniter, and also the safety valve just in case, as we were going to be fixing this on Christmas eve, so the oven could be used for Christmas dinner. Your agent... Read more
Burner won't light or flame is weak? This gas valve controls flow to your range surface burner for reliable ignition and heat control. Moderate DIY.
Replaced the old valve with a new one from AppliancePartsPros.com. I watched one of the YouTube videos to get an idea of what the process would entail. I gathered the tools I would require, plus a work light. The repair/replacement went pretty good. One thing the video I watched didn't cover was adjusting the valve for a propane system. I compared my old valve to the new one and saw that I would have to screw down the oven gas outlet until it "bottomed out". Read more
Replace a gas range burner valve that's broken, stuck open, or causing hard-to-adjust flames. Moderate DIY repair requires raising the stovetop.
After turning off the gas and unplugging the electricity, I removed all the burners from the stove top using a 3/16" hex socket. Then used a 1/4" socket to removed two or three screws under each burner which hold the burner base to the bottom of the top panel. Then pulled all the knobs and removed the front panel which was held in by two Phillips screws accessible from underneath the panel. It helps to open the oven door to get at these screws. With the knob panel gone, I removed two screws... Read more
Burner won't light or knob won't turn? This top burner valve controls gas flow to restore reliable ignition and flame control. DIY-friendly replacement.
Called repairman who diagnosed the problem. He said burner valve would cost around $125. I went online and found it for $35. Sears direct cost $43. Repairman installed and works great. Appliance parts was same part for less and shipped overnight for $9. Read more
Oven won't light even though igniter glows? Burner lights only when valve is tapped? Replace the dual gas safety valve. DIY install in under 1 hour.
From the Appliance Parts website I watched a 3 minute Youtube video. The video actually explained the process on another range but it was enough information for me to do the project myself. The part came 2nd day UPS and I installed it in under an hour. The only hitch was that I didn't see the note (maybe it wasn't there) that explained how the valve is set for Natural gas and that for LP gas I'd need to adjust the jet that goes into the burner tube. Maybe that was on the video. Read more
This safety valve controls gas flow to the oven burner, opening only when the ignition system calls for heat. Replacing a weak or stuck valve restores reliable ignition and consistent oven temperatures for safe, dependable baking and roasting. What it does:
This surface burner gas valve regulates the flow of gas to the burner on your range or cooktop, enabling proper ignition and flame control. Replacing a worn valve restores safe operation and consistent flame performance.
Found the problem through troubleshooting. Looked up the part on appliance parts pro. It was at my doorstep in 2 days. Replaced old gas safety valve. Oven works great again. Read more
This safety valve controls gas flow to the oven burner. When signaled by the igniter, it opens to allow ignition and helps maintain consistent heat, supporting safe, reliable preheating and baking performance.
I called AppliancePartsPros.com to see if they carried the parts that I needed. They knew what parts I needed and they were in stock. When the valves arrived I took the stove apart and replaced the valves. The valves were easy to replace with a minimum amount of tools: A screwdriver, adjustable end wrench, and a 1/4" drive socket set. I have all the tools necessary to do this job, but if I didn't and had to buy them, it would still be less expensive than hiring a repair person to do this job... Read more
Burner won't light or flame height won't adjust? This top burner valve controls gas flow to restore reliable ignition and precise flame control.
Fixes oven not heating or slow to heat issues. Controls gas flow to burner for safe ignition. Common repair for delayed heating or no heat problems.
Range oven not heating? Safety valve controls gas flow to burners. Requires voltage testing at igniter connection. Moderate difficulty repair.
Replaced the safety valve. Read more
Burner won't light or flame is weak? This top burner valve controls gas flow to restore proper ignition and flame adjustment on your gas range.
Burner won't light, stays on, or flame is uneven? This top burner valve controls gas flow to restore safe on/off control. Typical repair time: 45 minutes.
Ordered a new valve from you which was shipped the same day and arrived two days later,With excellent tracking. Had a little trouble installing it. However, I called , talked to your service rep who emailed me a service manual and even told me what page to look on. It can't get much better than that. Read more
Oven won't heat but igniter glows? A faulty safety valve prevents gas flow even with a hot igniter. This valve restores proper gas control.
Burner won't ignite or flame won't adjust? This top burner valve controls gas flow to your cooktop burner, restoring proper ignition and flame control.
This water inlet valve controls water flow to the refrigerator dispenser and ice maker, restoring proper dispensing and ice production. It replaces a failed or leaking valve to stop drips and ensure steady water fill. What it does: