Frigidaire Washer Parts

Washer won't drain or has standing water? This drain pump actively removes water after each cycle. DIY-friendly repair, typically takes under 20 minutes.

Replaces the cracked or broken outer door panel on your washer. Restores door alignment and supports the glass. Fixes broken hinge tabs or worn trim.

Replaces a cracked, scratched, or cloudy outer door lens. This clear plastic panel forms the exterior of your dryer's door window for visibility into the drum.

This replacement door glass forms the clear window in the door of select front-load units, restoring safe visibility and proper door fit. Replace a cracked, chipped, or shattered pane to prevent leaks and ensure the door seals and latches correctly. What it does

• Creates the viewing window in the door and mates to the door gasket/boot
• Helps maintain a proper seal to contain wash action
• Restores safe operation when the original glass is damaged
• Common symptoms: visible cracks or shattering, water leaking from the door area, door not closing flush, rattling glass

• 1 door glass pane

• Disconnect power and turn off water supply before service
• Wear cut-resistant gloves and eye protection; handle glass carefully
• Remove the door, set it on a padded surface, and transfer trim/gasket as designed
• Tighten fasteners evenly and check gasket alignment to prevent leaks

This dispenser assembly replaces a worn or damaged refrigerator dispenser to restore reliable dispensing of water and ice. It provides the dispenser housing and interface needed for proper user operation and sealing at the door. What it does:

• Houses the dispenser components and provides the push-lever/door opening for water and ice delivery
• Restores a broken, cracked or loose dispenser opening that causes poor engagement or cosmetic damage
• Helps stop minor leaks or drips at the dispenser area when seals and gaskets are intact
• Eliminates sticking or misaligned dispenser operation that prevents normal dispensing

• Disconnect power and shut off the water supply before beginning any work.
• Installation typically requires removing the refrigerator door panel(s) and detaching the old dispenser from the inner door; keep fasteners for reuse unless replacements are provided.
• Handle plastic parts gently to avoid cracking; inspect door seals and gaskets and replace if worn.
• After installation, restore power and water, then test dispenser operation and check for leaks.

White timer knob for washer control panel. Replaces worn, cracked, or missing knob that won't engage the timer shaft. Screws onto timer control shaft.

This electronic control is a direct-replacement circuit board that manages your appliance's primary functions and user interface, restoring responsive controls and reliable cycle management when the original control fails. Ideal for addressing control-related faults. What it does:

• Replaces the appliance's main control board to restore normal electronic operation and user input response.
• Can stop or prevent erratic displays, intermittent operation, or unresponsive controls caused by a failing board.
• Helps correct issues where cycles do not start, stop, or advance as expected due to control failures.
• Resolves error codes or fault indicators that point to control/board malfunction.

• Disconnect all power before beginning—this part is live-voltage sensitive.
• Handle the board carefully to avoid static damage; ground yourself and avoid touching circuitry.
• Verify the part number on the old board matches before installing.
• After installation, restore power and run a basic function test.

Replacement pin for washer components. Secures and connects internal parts. Needed when original pin is broken, missing, or worn from use.

Replaces a cracked or broken splash tub cover assembly on your washer. Installs around the tub to protect internal components from water damage.

Rubber grommet cushion for laundry center washers. Isolates vibration and prevents wear where components pass through openings. Replaces worn or missing.

Replacement drum drive belt for washers. Transfers motor power to spin the drum during wash cycles. Replace if drum won't spin or belt shows wear.

Water inlet hose for washers and laundry centers. Connects the water supply to your machine. Replace if cracked, torn, leaking, or damaged.

Secures the top or front panel to your laundry center frame. Replace if bracket is cracked, broken, or missing to restore proper panel alignment.

Replace your washer's timer knob if it's cracked, broken, or missing. This control knob attaches to the timer shaft on the control panel for cycle selection.

Replace your washer's cracked or missing access cover. Restores exterior protection, shields internal components from dust and moisture, and provides a clean finished appearance.

This damper is the refrigerator air-control flap that regulates airflow between compartments to help maintain consistent temperatures and proper cooling. It replaces a worn or stuck damper to restore normal airflow and temperature balance. What it does:

• Opens and closes to direct cold air where needed between freezer and fresh-food sections
• Helps maintain even temperatures and prevents one compartment from getting too warm
• Common symptom: uneven cooling or warm fresh-food section despite running compressor
• Common symptom: damper stuck or not moving, causing poor temperature control

• Disconnect power to the appliance before starting any repair
• Remove interior panels to access the damper; use basic hand tools
• Handle the damper and any wiring harness carefully to avoid damage
• After installation, verify damper operation and allow time for temperatures to stabilize