Frigidaire Washer Parts

Rotary control knob that fits onto the control shaft to select settings. Replace if your original knob is cracked, broken, worn, or missing.

Replaces cracked, warped, or broken inner door panel on front-load washers. Restores door structure and provides mounting surfaces for bins and seals.

This is a small C-clip or retainer ring that secures the idler pulley to its bracket on a laundry center. It keeps the pulley in place so the drive belt maintains proper tension against the drum. Replace this ring if the idler pulley has come loose, the drum belt slips or falls off, or the dryer drum does not spin properly.

Rubber bumper cushions washer lid closure. Installs between lid and cabinet to absorb impact and reduce noise. Replace if worn, cracked, or missing.

Trunnion assembly for washing machines. Supports and allows outer tub rotation during wash and spin cycles. Replace if cracked, worn, or damaged.

White timer knob for washer control panel. Replaces worn, cracked, or missing knob that won't engage the timer shaft. Screws onto timer control shaft.

Rubber grommet cushion for laundry center washers. Isolates vibration and prevents wear where components pass through openings. Replaces worn or missing.

Replacement drum drive belt for washers. Transfers motor power to spin the drum during wash cycles. Replace if drum won't spin or belt shows wear.

This is a rubber hose that connects the detergent or fabric softener dispenser to the wash tub, allowing dispensed products to flow into the drum during the wash cycle. Over time this hose can crack, clog, or develop leaks. Replace it if you notice detergent not reaching the tub, water leaking near the dispenser area, or visible deterioration of the hose.

This is a 10-16 x .312 sheet-metal screw with a quad-style panel head used to secure appliance panels and trim. It replaces missing or damaged screws to help stabilize panels and reduce rattling. What it does:

• Fastens control panels, trim pieces, and thin sheet-metal components
• Restores secure fit where screws are missing or stripped
• Helps stop panel vibration, rattling, or misalignment caused by loose fasteners
• Small, common mounting screw for interior and exterior appliance panels

• One 10-16 x .312 quad panel head screw (quantity: 1)

• Disconnect power to the appliance before working on panels or controls
• Use the correct screwdriver head to avoid stripping the quad head
• Tighten by hand; do not overtighten to prevent stripping or cracking panels
• Keep extra screws on hand; replace any that are corroded or damaged

Rubber O-ring seal prevents water leaks at hose connections and fittings. Replace when worn or cracked to restore tight seal and stop dripping. Verify fit.

Secures hoses to fittings, preventing leaks in water and drain lines. Replace when connections loosen or leaks appear. Verify fit with your model number.

Fix a washer that loses power, won't spin properly, or has an unresponsive control panel. This electronic control board restores normal operation.

Replace your washer's cracked or missing access cover. Restores exterior protection, shields internal components from dust and moisture, and provides a clean finished appearance.

This damper is the refrigerator air-control flap that regulates airflow between compartments to help maintain consistent temperatures and proper cooling. It replaces a worn or stuck damper to restore normal airflow and temperature balance. What it does:

• Opens and closes to direct cold air where needed between freezer and fresh-food sections
• Helps maintain even temperatures and prevents one compartment from getting too warm
• Common symptom: uneven cooling or warm fresh-food section despite running compressor
• Common symptom: damper stuck or not moving, causing poor temperature control

• Disconnect power to the appliance before starting any repair
• Remove interior panels to access the damper; use basic hand tools
• Handle the damper and any wiring harness carefully to avoid damage
• After installation, verify damper operation and allow time for temperatures to stabilize

Cushion bumper for washer installation. Absorbs vibration and protects cabinet surfaces. Replace if cracked, compressed, or missing to restore proper support.