We use cookies and similar tools for site analytics and advertising. By using our site, you agree to this. See our Privacy Policy for details. Do Not Sell or Share My Personal Information
Need Help?
Call
Spring protector installs on washer suspension springs to prevent wear and damage. Replace if cracked, broken, or missing to protect suspension components.
I believe the shock absorbers were bad and caused too much stress on the spring, breaking it. I replaced the spring, spring protector, and shock absorbers. I got lucky; when I got the drum back up where it belonged I saw that the door boot seal straightened itself back out and wasn’t damaged so I didn’t have to replace it. The whole job took about three hours and the washing machine runs more smoothly now than it did when it was new! Read more
Usually ships within 4 - 14 days
Fix a washer that won't advance through cycles or keeps running continuously. This timer replacement restores proper cycle control. DIY-friendly repair.
Ordered the replacement timer (perfect match, packed nicely, and delivered on the 3rd day after order!), sprayed a tiny bit of grease on the motor gear, and a little silicone spray on the control wheel, and installed the part. Also, noticed that a badly balanced wash load could cause the tub to slam into the edge of the timer. I fashioned a cushion out of heavy foam and attached it under the center metal brace on top, to dampen the upward movement of the drum. New timer works great. Time... Read more
Mounting bracket for washer and laundry center models. Secures components in place during operation. Replace if cracked, bent, or broken to restore stability.
This is a temperature selector switch used in a washing machine to control the water temperature setting for wash and rinse cycles. It connects to the control panel and signals the water inlet valves to mix hot and cold water according to the selected setting. Replace this switch if the washer does not respond to temperature selections, only fills with one water temperature, or if the switch knob feels loose or unresponsive.
Fix a washer that won't start, shows error codes, or stops mid-cycle. This main control board restores cycle operation and digital controls in about 1 hour.
After asking a few question to a repairman I took machine apart checked waterlines and water orifices for clogs....none. Did a ohm check of the four water regulating solenoids....OK! Next and last was the control board. Ran machine in other cycles soap dumped. Control board....BAD! Replaced it. It all works fine now. Total time for repair about an hour. Saved $200+part for a repairman to come out and do it. Total cost $140 for part. Read more
This is a pressure-activated switch that monitors the water level inside the washer tub. It signals the control board to stop filling when the correct water level is reached and helps initiate the wash and drain cycles. Replace this switch if the washer overfills, underfills, does not fill at all, or fails to advance through cycles properly.
Replacement mounting nut for washers and laundry appliances. Secures internal components and panels. Order if original nut is stripped, missing, or broken.
Replace a faulty washer timer if cycles won't advance, the machine won't start, or it stops mid-cycle. Moderate difficulty repair, typically 30-45 minutes.
Fix a washer that won't start, won't advance cycles, or has no display with this control board. Common repair for unresponsive washers. Moderate difficulty.
Replacement pin for washer components. Secures and connects internal parts. Needed when original pin is broken, missing, or worn from use.
Shipping block for washers, installs inside cabinet to secure the tub during transport or moving. Replace if lost, broken, or missing from original packaging.
Coiled roll pin secures shafts, rollers, and linked components in washers. Replace if worn, damaged, or missing to restore proper alignment.
The washer agitator stud cap is a small cover piece that fits on top of the central agitator post in top-loading washing machines. Replace this cap if it's cracked, missing, loose, or if fabric is getting caught on the exposed agitator mechanism.
Washer door boot seals the drum opening to prevent water leaks. Replace if torn, cracked, or moldy to restore proper sealing. Confirm fit by model number.
Replacement drum drive belt for washers. Transfers motor power to spin the drum during wash cycles. Replace if drum won't spin or belt shows wear.