General Electric Cooktop Wire, Harness, Power Cord

This burner wire harness connects the range/oven ignition system components so the burner safely receives the correct spark or hot-surface signal. It replaces a damaged or worn harness to restore reliable ignition performance. What it does:

• Routes electrical connections from the igniter/spark module to the burner assembly
• Enables ignition sparks or hot-surface signals to reach the burner for reliable lighting
• Can stop symptoms such as burners failing to light, erratic or intermittent ignition, or continuous clicking
• Helps prevent loose or shorted wiring that can cause ignition faults

• Disconnect electrical power and shut off gas supply before starting any repair
• Label or photograph original wiring locations to ensure correct reconnection
• Route the harness clear of direct heat and moving parts; secure with original clips or ties

Wire harness with LED assembly that connects an appliance's control circuitry to an LED indicator or lighting module, restoring proper indicator illumination and signal routing when the original harness is damaged or intermittent. What it does:

• Provides the electrical connection and mounted LED used for control/indicator or internal lighting circuits
• Transfers power and signal between the control board and the LED/indicator
• Can correct symptoms such as a dim, flickering, or non-lighting indicator or intermittent LED function
• Replaces a damaged or corroded connector that causes loss of indicator/lighting

• Disconnect power to the appliance before attempting replacement to avoid shock or damage
• Handle connectors and the LED assembly carefully to avoid bending pins or damaging wiring
• Route and secure the harness to match original routing and avoid pinch points or heat sources
• Test operation after installation; for wiring diagrams and connector locations

This element wire harness connects the heating element to your range or wall oven's internal wiring, delivering power for proper heating. Replace a burned or brittle harness to restore consistent oven performance and safe, reliable operation.

• Supplies electrical current from the appliance wiring to the heating element
• Maintains secure, heat-resistant connections at the element terminals
• A damaged harness can cause no heat, slow preheats, or intermittent heating
• Visual clues include burned insulation, discoloration, or loose/melted connectors at the element

• Disconnect power at the breaker and allow the oven to cool completely
• Access element connections from the rear panel or inside the oven (model dependent)
• Note routing; move one connection at a time to the new harness and ensure terminals are fully seated
• Route wires away from sharp edges and hot surfaces; verify secure connections before restoring power

High-voltage harness routes power between high-voltage components in a microwave oven, restoring safe electrical connections and preventing intermittent operation or arcing when replacing a damaged or burned wiring assembly. What it does:

• Connects the microwave's high-voltage components to maintain proper power flow.
• Failing or damaged harnesses can cause no-heat, intermittent heating, arcing, burning smell, or blown fuses.
• Replaces frayed, melted, or corroded high-voltage wiring that risks shorting or unsafe operation.
• Designed to restore original electrical routing and secure connector fit for reliable operation.

• Disconnect power and unplug the appliance before servicing. Ensure the high-voltage capacitor is properly discharged—do not attempt service without this step.
• Inspect connectors, insulation, and routing; replace damaged clips or retainers and secure wiring away from sharp edges and moving parts.
• Follow the wiring diagram for correct connections.
• Never operate the appliance with covers or safety panels removed.

This ignitor harness connects the oven's right-side ignitor to the appliance wiring, restoring reliable spark and proper burner ignition. It's a direct-fit harness used where the right ignitor circuit needs a replacement connection. What it does:

• Transfers electrical power and signals between the oven control and the right-side ignitor to enable burner ignition
• Commonly used when a burner or ignitor fails to light, sparks inconsistently, or has a damaged/loose connector
• Maintains correct connector alignment and insulation to ensure safe, consistent ignition performance
• Replaces worn, frayed, or melted harnesses that can cause intermittent operation or open circuits

• One ignitor harness (right-side)

• Disconnect power (and shut off gas supply on gas appliances) before starting any repair
• Match connector types and routing to the original harness; avoid stretching or pinching wires
• Inspect nearby wiring and terminals for heat damage; replace damaged components as needed

Replacement burner wire harness that restores the ignition wiring connection for a gas range surface burner, helping re-establish consistent sparking and reliable burner ignition for safe cooking operation. What it does:

• Provides the electrical connections between the burner igniter/spark electrode and the range's ignition module/control.
• Replaces damaged, cut, or frayed wiring that can cause no-spark, intermittent ignition, or continuous clicking at the burner.
• Routes and secures ignition wires to keep connections stable and reduce heat/rub-related failures.
• Helps the ignition system deliver consistent sparks so burners light reliably.

• Disconnect electrical power and shut off the gas supply before beginning any service.
• Compare the new harness to the original; transfer and reconnect terminals one-to-one and secure any routing clips or fasteners.
• Route wires away from hot surfaces and sharp edges; avoid stretching or pinching the harness.

This burner wire harness assembly routes power and signals between the control and the burner components so your range or oven can ignite and operate correctly. It replaces a damaged or corroded wiring harness to restore reliable ignition. What it does:

• Carries electrical connections from the control/igniter to the burner for proper ignition and heating
• Replaces broken, melted, or corroded wires that can cause intermittent or failed ignition
• Helps stop sparking issues or burners that don't light when the control calls for heat
• Restores secure connector fit and proper wire routing to prevent shorts or arcing

• One burner wire harness assembly

• Disconnect power (and gas supply for gas ranges) before starting any repair
• Handle connectors gently and match connector shapes; ensure all plugs seat fully
• Route and secure the harness away from high-heat surfaces and moving parts

Note: Ignitor wires

This harness module connects and routes electrical signals between components to restore reliable circuit connections and control communication. It replaces a damaged or worn module to help appliances power and operate correctly. What it does:

• Routes power and signal connections between internal components to ensure consistent electrical continuity
• Replaces broken, frayed, or corroded wiring that can cause intermittent operation or loss of function
• Helps resolve symptoms such as lights or controls not responding, intermittent cycles, or non-start conditions when traced to the harness
• Maintains correct connector fit and pin alignment for secure component mating

• One harness module as shown

• Disconnect power before servicing to avoid shock or damage
• Inspect connectors and mating components for damage or corrosion before installation
• Secure harness away from sharp edges and moving parts; follow OEM routing and fastening points