General Electric Cooktop Valve

Restore smooth, controllable flame on a gas cooktop burner. This surface burner valve regulates gas flow to an individual top burner, allowing precise adjustment from low simmer to full boil and helping stop leaks when turned off.

• Controls gas flow to one surface burner
• Common failure signs: burner won't light or is very weak, knob turns hard or feels loose, gas odor at the valve, flame will not adjust smoothly
• Helps ensure reliable ignition and steady flame once replaced

• Disconnect gas and power before servicing; ventilate the area if gas odor is present
• Label and transfer the knob shaft orientation and any mounting hardware from the original
• Check and reuse the correct orifice and inlet fittings from the old valve if required by your model
• After installation, perform a leak check on all connections with approved leak-detection solution

This gas valve assembly controls the flow of gas to the appliance's burners so they ignite and maintain a steady flame. Replace a failing valve to address ignition problems and restore normal heat delivery. What it does:

• Regulates gas flow during ignition and operation to maintain consistent burner flame
• Enables burners to light when the ignition system calls for gas
• A faulty valve can cause burners to fail to light, produce a weak or uneven flame, or result in repeated ignition attempts
• If you smell gas, stop use immediately and follow safety guidance — do not try to power or test the appliance

• Turn off the appliance power and shut off the gas supply before starting work; if you detect a strong gas odor, leave the area
• Basic hand tools may be required; gas and electrical connections must be properly tightened and sealed
• Follow the manufacturer's installation instructions and local codes
• After installation, check for leaks using an approved leak-detection method and verify proper ignition and operation

This surface burner valve regulates gas flow to a cooktop/range burner. Used in the left front or right rear position, it restores smooth knob control so the burner lights and the flame adjusts properly from simmer to high. What it does:

• Meters and shuts off gas to a single top burner
• Position-specific: intended for the left front or right rear location on the manifold
• Helps resolve issues like a hard-to-turn knob, inconsistent flame height, or a burner that won't adjust as expected
• Can correct no-gas flow to that burner when the original valve is blocked or failed

• 1 gas surface burner valve (LF/RR orientation)

• Shut off gas supply and disconnect power before servicing
• Lift the cooktop/top panel to access the manifold; note hose/tube routing and valve orientation
• Transfer any orifice holder/fittings from the old valve as required; avoid overtightening compression connections
• Use an approved gas-thread sealant if specified and leak-test all joints with a soap-and-water solution before use

This replacement valve kit restores proper flow control in compatible GE appliances, helping resolve failures related to supply, dispensing or leaks. It's a direct-replacement style assembly intended to return the affected system to normal operation. What it does:

• Regulates flow to the appliance's system to enable normal filling, dispensing or operation
• Replaces worn seals and moving valve components that can cause intermittent function
• Stops or reduces leaks and unintended flow when the original valve assembly fails
• Helps correct symptoms such as no fill/dispense, intermittent operation, or persistent leaking

• Always disconnect power and, if applicable, shut off the water and/or gas supply before starting
• Handle components carefully; use manufacturer-recommended seals, gaskets and mounting hardware
• Test for leaks and correct operation after installation

This water inlet valve controls water flow to the refrigerator's ice maker and dispenser, restoring normal ice production and water dispensing when the valve fails. Durable direct-fit replacement for affected GE refrigerators. What it does

• Opens and closes to supply water to the ice maker and dispenser when the dispenser or ice maker calls for water.
• Commonly used to fix no-water or low-water flow to the ice maker or dispenser.
• Stops water flow when the refrigerator is off to prevent leaks or flooding.
• Works with electrically controlled solenoid valves in the water system.

• One water inlet valve

• Disconnect power and shut off the household water supply before starting work.
• Access may require removing interior panels, the back cover, or toe panel depending on the model.
• Replace using the existing mounting and wiring connections; use new water line fittings if old fittings are corroded.

This gas surface burner valve controls the right-rear burner on your cooktop or range, regulating gas flow as you turn the knob. Replacing a worn valve restores consistent ignition and precise flame control at that position.

• Regulates gas flow to the right-rear surface burner for on/off and flame level control
• Common symptoms include no ignition, uneven or weak flame, or poor flame adjustment at that burner
• Stiff, loose, or wobbly knob action at the RR position can indicate internal valve wear
• If a gas odor is detected, shut off gas and have the unit serviced before use

• Disconnect power and shut off the gas supply before servicing
• Remove the knob and front panel to access the manifold; note valve orientation and connections
• Support the manifold with a second wrench while loosening/tightening fittings to avoid damage
• After installation, perform a soap-solution leak test on all connections and verify proper ignition and flame

This gas valve controls fuel flow to a cooktop or range burner so the burner ignites and holds a steady flame. Replaces a worn or failed valve to restore normal burner operation and safe ignition. What it does:

• Regulates gas flow to a single surface burner so the igniter can light the flame
• Stops gas flow when the control is off to prevent unintended flow
• Common symptoms: burner won't light, weak or no flame, or a burner that won't stay lit
• Works with the range's existing igniter and control knob to modulate flame

• One gas valve

• Turn off both gas supply and electrical power before starting work
• Tighten gas fittings to specified torque and test all connections for leaks using a soap solution or approved leak detector
• Check that replacement valve matches original part number and orientation before installing

This replacement valve kit controls water flow into the appliance, restoring proper fill and operation. It replaces a worn or failing inlet valve assembly to help stop leaks and restore normal fill cycles. What it does:

• Opens and closes to allow water into the appliance during fill cycles
• Stops water flow when cycle is complete to prevent overfilling
• Commonly used to address no-fill, slow-fill, or continuous-fill symptoms
• Helps stop valve-related leaks when the valve assembly is the source

• One valve kit

• Disconnect power to the appliance and shut off the water supply before starting
• Handle and position the valve carefully; use appropriate hand tools
• Inspect hoses and fittings and replace any damaged seals or clamps

This safety valve controls gas flow to the range/oven burner and helps ensure reliable ignition and shutoff for safe cooking. Replacing a worn valve restores proper gas delivery and can stop intermittent heating issues. What it does:

• Opens and closes the gas supply to the oven/burner so burners ignite only when commanded
• Prevents uncontrolled gas flow when the appliance is off
• Common replacement when burners or oven fail to light or heat inconsistently
• Can address persistent clicking, weak flame, or failure to maintain temperature

• One safety valve

• Turn off the appliance power and gas supply before starting work
• Inspect and replace any damaged gaskets or fittings during installation
• Use proper tubing fittings and a leak test after reassembly; check for tight seals

This gas valve controls gas flow to the burners and oven, restoring reliable ignition and consistent heat when the burner won't light or the oven won't heat properly. Designed as a direct replacement part. What it does:

• Regulates gas supply to the oven and cooktop burners for proper ignition and consistent flame
• Commonly replaces valves that cause burners not to light or the oven to not maintain heat
• Helps stop irregular gas flow that can lead to weak or fluctuating flames
• Works with the appliance's safety and control systems to open and close gas flow as commanded

• One gas valve as shown

• Shut off the gas supply and disconnect power before starting any repair
• Only install on compatible appliances;
• Tighten gas fittings to the manufacturer's torque spec and test with a leak solution

This valve kit is the replacement assembly that controls fluid flow to the appliance's internal components, restoring proper operation and helping stop flow-related failures. It replaces a worn or damaged valve to return reliable performance. What it does:

• Regulates flow through the appliance so water or fluid reaches the correct component
• Re-establishes proper filling, dispensing, or flow when a valve has failed
• Stops intermittent or no-flow symptoms that can prevent normal appliance function
• Helps address leaks or drips originating at a faulty valve connection

• Disconnect power and shut off the water or fuel supply before beginning service
• Follow the appliance service manual and use OEM-compatible fittings and seals
• Inspect hoses, connectors and mounting hardware; replace any damaged parts
• After installation, restore supply, check for leaks and verify proper operation