General Electric Range Bracket & Flange

This door bracket secures a refrigerator or freezer door to the cabinet, helping maintain proper alignment and smooth opening/closing. It replaces worn or damaged brackets to reduce door sag and improve sealing. What it does:

• Serves as the mounting point between the door and cabinet/frame to hold door position
• Restores proper door alignment to prevent rubbing, gaps, or uneven closing
• Helps the door seal correctly, reducing cold air loss and temperature issues
• Reduces door sag and excessive play that can cause noisy or uneven operation

• Disconnect power to the appliance before beginning work and remove contents from the door
• Support the door while removing fasteners to prevent dropping; an assistant may be helpful
• Use common hand tools; retain original fasteners unless replacements are specified
• If door alignment or gasket sealing issues persist after replacement, inspect hinges and seals

This control bracket secures the appliance control assembly to the cabinet, helping keep buttons, knobs, and the control board properly aligned for reliable operation. Designed to restore stable control-panel mounting after damage or wear. What it does

• Holds the control/module assembly in the correct position so front controls operate smoothly
• Prevents excessive movement or vibration that can cause intermittent button or knob issues
• Restores proper alignment after a broken or bent mounting tab
• Helps maintain electrical connections by stabilizing the control module

• Designed to replace a broken or bent bracket; inspect surrounding clips and fasteners for damage before installing
• Power off and unplug the appliance before attempting removal or installation to avoid shock
• Typical installation requires removing the control panel or console—retain screws and grounding hardware
• Handle the board carefully to avoid static discharge or connector damage

This anti-tip brace secures the range to the floor or wall to help prevent the appliance from tipping forward when a heavy load is on an open oven door or when pressure is applied to the top edge. It restores a key safety restraint and helps stabilize the appliance. What it does

• Anchors the range to reduce forward tipping when the oven door is open or heavy items are placed on the door
• Helps prevent accidents and appliance movement during normal use
• Works with the range's built-in leveling and mounting points to provide a secure attachment
• Commonly replaced after a move, installation, or if the original bracket is damaged or missing

• One anti-tip brace

• Follow the appliance installation manual for correct placement and mounting location
• Unplug the appliance (or shut off power) and remove access panels as needed before installing
• Use appropriate fasteners for your floor/wall material; secure to framing or floor as specified

This bracket latch secures the appliance door latch assembly to the cabinet so the door fastens reliably and stays closed during use. It's a simple replacement that restores proper door engagement and reduces door rattling. What it does:

• Anchors the door latch so the door closes and locks correctly
• Restores secure door engagement to prevent the door from popping open
• Helps eliminate rattling or misalignment caused by a broken or bent bracket
• Works with the existing latch assembly and hardware to maintain normal operation

• Disconnect power (and water supply for refrigerators) before servicing
• Typical installation uses basic hand tools; keep track of mounting screws
• Inspect the latch and striker for wear and alignment when replacing the bracket

This mounting bracket secures the range/oven power supply assembly to the appliance frame, keeping the supply stable and properly positioned for reliable operation and safe electrical connections. What it does:

• Holds the power supply assembly in place to prevent movement and vibration
• Helps maintain correct alignment of electrical connections to avoid intermittent power
• Reduces strain on wiring and components that can cause arcing or connection issues
• Supports safe operation by keeping the supply mounted away from heat and other parts

• Turn off and disconnect power at the breaker before servicing to avoid electrical shock
• Handle sharp sheet-metal edges with care and wear gloves
• Verify proper orientation and secure all fasteners; confirm wiring is routed clear of moving parts and heat sources

This bracket secures the Quantum SI assembly in place, helping keep the control module stable for reliable operation. A direct-fit replacement when the original bracket is damaged or missing. What it does

• Provides a mounting point and structural support for the Quantum SI control assembly
• Keeps electrical and control components aligned to prevent loose connections or vibration
• Helps restore proper positioning after impact or wear
• Supports reliable operation by maintaining OEM component location

• One replacement bracket as shown

• Inspect surrounding components and mounting hardware; replace any stripped or damaged fasteners
• Power off and disconnect the appliance before attempting any repairs
• Tighten screws to secure the bracket without over-torquing