General Electric Range Motor

This convection fan assembly circulates heated air inside the oven cavity for more even baking and roasting. Replacing a worn or noisy fan restores proper airflow and helps maintain stable temperatures during convection cooking.

• Moves hot air across the cavity during convection modes for uniform results
• Helps the oven recover heat faster and reduces hot/cold spots
• Common symptoms of failure: loud humming, squealing, or rattling; fan not spinning; poor or uneven convection performance
• Can cause longer cook times or inconsistent browning when not working properly

• Disconnect power at the breaker and allow the appliance to cool completely
• Access the convection fan from the rear panel or interior back cover, depending on model; retain all screws and shielding
• Note wire locations and mounting orientation; install the new assembly in the same position
• Before restoring power, ensure the blade spins freely and does not contact the shroud or liner

This motor drives the oven's convection fan to circulate hot air for even, consistent baking and roasting. Replace a noisy or stalled motor to restore proper airflow and uniform temperatures throughout the cavity.

• Spins the convection fan to move heated air across all racks
• Helps reduce hot and cold spots for more even cooking results
• Failure signs include the fan not running, running slowly, or making loud humming/grinding/squealing noises
• Symptoms can include uneven baking/roasting, longer preheat times, and poor browning

• Disconnect power at the breaker before servicing
• Access varies by model; remove appropriate panels to reach the motor and fan
• Transfer the existing fan blade and any reusable mounting hardware if your model uses separate parts
• After installation, ensure the blade spins freely and clears the shroud before restoring power

This is the convection fan motor for select ovens. It drives the rear convection fan to circulate hot air for more even baking and roasting performance.

• Spins the convection fan to move heated air throughout the oven cavity
• Helps protect against uneven cooking, hot spots, or longer preheat times
• A failed motor may hum, seize, not start, or run noisily
• Restores proper convection airflow when the original motor wears out

• Disconnect power before service; oven parts and wiring can be live and hot
• Access is typically from the rear or through the oven interior; remove the fan blade and mounting screws to replace the motor
• Transfer any brackets or wiring in the same orientation; note wire positions or take a photo
• After install, verify the fan spins freely by hand before restoring power

Note: Motor only - convect fan WB2X8351 not included.

A single-speed convection fan motor that circulates hot air for more even oven cooking and consistent temperatures. Replacing a worn or failed motor restores convection airflow and helps reduce uneven baking. What it does:

• Circulates heated air inside the oven cavity to support convection bake and roast modes
• Restores consistent oven airflow for more even cooking and baking results
• Helps when the convection fan doesn't run, runs intermittently, or makes unusual/grinding noises
• For use where a single-speed convection blower motor is specified by the manufacturer

• Disconnect power to the appliance before servicing to avoid shock hazard
• Allow the appliance to cool completely before accessing the oven cavity
• Verify wiring connections and mounting orientation match the old motor; transfer fan blade or bracket if required

The Convection Motor is an OEM part compatible with GE wall ovens and convection ranges. As the primary component driving air circulation inside the oven cavity, it is responsible for the convection baking and roasting functions.

By circulating warm air around the food at high speed, the convection motor allows for faster and more even cooking without compromising quality. Causes of failure can include excess dirt or debris obstructing the motor shaft or blades, damage to motor wiring from heat, or normal component wear over time.  

Symptoms of a bad convection motor include:

• Convection cooking mode not working at all  
• Much longer than normal cooking times
• Unevenly cooked food despite rotation
• Loud grinding or whirring noises from inside the oven

This GE OEM replacement motor restores efficient convection performance. It is also compatible with Hotpoint, RCA, and select Kenmore ovens. Replace yours today for reliable cooking power.
 

This blower assembly circulates air through the appliance to support drying and venting, restoring proper airflow for consistent performance. It replaces a worn or damaged fan wheel and housing to reduce overheating and poor drying. What it does:

• Moves air through the appliance to aid drying and ventilation
• Restores airflow lost from cracked, warped, or broken blower wheel
• Helps eliminate overheating, long-dry times, or reduced airflow
• Works with the motor and ducting to maintain proper exhaust flow

• One blower assembly

• Disconnect power before servicing to avoid shock or injury
• Inspect motor shaft and mounting before installing; replace any damaged hardware
• Ensure blower is oriented and secured per manufacturer alignment to prevent noise or imbalance
• Verify clear, unrestricted ducting after installation for proper performance

Tangential blower that moves air through the oven's ventilation and control areas to help keep components cool and vent heat. Replacing a failed blower restores airflow for quieter operation and more consistent cooling around electronics. What it does:

• Circulates air across the oven vent and control area to dissipate heat; symptoms of failure include little or no airflow.
• Helps cool control electronics and nearby components; failure can cause high temperatures or thermal-related shutdowns.
• Reduces noisy or rough fan operation when bearings or motor wear.
• Supports proper venting after use to help the appliance cool down safely.

• Disconnect power to the appliance before accessing or replacing the blower.
• Allow the appliance to cool fully; remove access panels to reach the blower.
• Handle the blower and connector gently to avoid damaging the motor shaft or wiring; ensure correct orientation when reinstalling.

The Blower Tangential 45mm is an OEM part for GE gas ranges. It is the convection fan that circulates heated air within the oven cavity during convection cooking cycles.

Symptoms of a bad blower tangential include:

• Lack of airflow inside the oven
• Uneven baking and roasting results  
• Inability to select convection cooking modes

Causes of failure can be worn bearings, burned out motor, or damage from excess heat over long-term use.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore gas range models. 

A 45 mm tangential blower that restores directed airflow in heating and cooling cavities to help maintain even temperatures and protect internal components. Fits factory blower mounts and connects to existing wiring harnesses. What it does:

• Moves air along the oven/cabinet cavity to promote even heat distribution and help vent hot spots
• Cools nearby electronics and components to reduce overheating risk
• Replaces worn or noisy blowers to restore proper airflow and reduce unusual motor noise
• Helps maintain designed airflow for venting and exhaust paths

• Disconnect power at the breaker before starting any repair
• Handle with care; blower edges and surrounding sheet metal may be sharp
• Verify blower orientation and wiring match the original before securing
• Basic hand tools typically needed; follow for panel removal and reassembly

This lower cooling fan assembly circulates air to cool internal components and help maintain proper airflow in the appliance. Replacing a worn fan restores quieter operation and helps prevent overheating of electrical parts. What it does:

• Moves air through the appliance cabinet to aid component cooling and temperature regulation.
• Reduces hot spots around controls, electronics, and motors that can cause premature failure.
• Commonly used when you hear unusual noise from the lower area or detect reduced airflow.
• Supports overall appliance performance and reliability by maintaining designed ventilation.

• One lower cooling fan assembly as shown

• Disconnect power before attempting any service to avoid electric shock.
• Inspect surrounding mounts and ducts for damage; replace any broken clips or supports.
• Use basic hand tools; confirm correct orientation and secure mounting before restoring power.

The Blower Motor is an OEM part for GE ranges. Within the oven cavity, it circulates air to help distribute heat evenly for thorough cooking.

Causes of a bad Blower Motor include wear from long term use, residue buildup on fan blades inhibiting air movement, or electrical issues such as loose wiring connections or a burned out motor coil.

Symptoms of a bad Blower Motor are:

• Inconsistent or improper baking and broiling
• Hot and cold spots inside the oven cavity
• Extended cooking times needed for foods

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This tangential blower moves cooling air through the appliance to protect internal components and the control area from excess heat. Replace a noisy or non-running fan to restore proper airflow and safe operating temperatures. What it does

• Circulates air across the appliance cavity and control compartment during and after heating cycles
• Helps prevent over-temperature shutdowns and protects electronic controls
• Reduces heat at the control panel and vent area
• Common symptoms: fan won't run, runs intermittently, or makes loud scraping/rumbling noises

• One tangential blower

• Disconnect power and allow the appliance to cool completely before servicing
• Access location varies by model; document wire connections and mounting orientation before removal
• Transfer any brackets, screws, or insulation from the original part if needed
• The fan spins freely and matches the original airflow direction before reassembly