General Electric Range / Cooktop / Oven Damper & Related

This vent tube directs heated air and moisture from the appliance to its exhaust path, maintaining proper airflow around internal components. Replace a cracked, warped, or missing tube to restore safe ventilation and help prevent heat and condensation buildup. What it does:

• Channels hot air and steam from the cavity to the outlet
• Helps prevent heat accumulation around controls and adjacent surfaces
• Reduces moisture/condensation at the vent outlet
• Common symptoms: excessive warmth near the console, persistent odors/steam, visible damage, or rattling from a loose/broken tube

• 1 vent tube

• Disconnect power; shut off gas. Allow the appliance to cool completely before servicing.
• Access and attachment points vary by model; refer to your service manual or diagram for location.
• Note the tube's orientation and routing; transfer any brackets or seals from the old part if present.
• Reuse existing screws/clamps and ensure the vent path is clear after installation.

This is a replacement vent tube designed to route exhaust air and restore proper ventilation in the appliance. Replacing a damaged or clogged vent tube helps maintain airflow and reduces the risk of moisture buildup or heat retention. What it does:

• Channels exhaust or vented air away from the appliance to maintain proper airflow
• Helps prevent moisture buildup and related odors when ventilation is impaired
• Can reduce overheating or performance issues caused by restricted venting
• Restores a secure path for airflow when the original tube is cracked, collapsed, or disconnected

• Disconnect power to the appliance before beginning work; for gas appliances, turn off the gas supply.
• Use basic hand tools and avoid sharp edges on sheet-metal near the vent opening.
• Ensure all connections are seated and sealed per the appliance diagram to prevent air leaks.

This vent tube assembly directs exhaust and heat away from the appliance cavity to help maintain proper airflow and protect internal components. It replaces a worn or damaged vent tube to restore normal venting performance. What it does

• Channels exhaust from the appliance outlet to the main vent path to prevent heat buildup.
• Keeps heat and combustion gases away from console and internal wiring.
• Helps reduce hot spots and odors that can occur with a damaged or disconnected vent.
• Fits into the appliance's venting system to restore intended airflow routing.

• Disconnect power (and gas, if applicable) before starting work.
• Remove access panels per the appliance service instructions; take care around sharp sheet metal.
• Verify orientation and secure mounting so the tube routes without kinks or pinching.

This vent tube directs heat and venting from the oven/radiant element to help maintain proper airflow and protect surrounding components. It's a direct-fit replacement designed to restore proper venting performance. What it does:

• Channels heat and vent airflow away from the radiant element and oven cavity
• Helps prevent hot spots and protect adjacent components from excess heat
• Replace when bent, cracked, corroded or blocking airflow
• Can resolve venting-related cooking issues and uneven broiling

• Vent tube

• Disconnect power to the appliance before starting any repair
• Remove oven panels and allow all components to fully cool before handling
• Handle carefully to avoid damaging ends or mounting tabs; use basic hand tools

This vent tube assembly routes exhaust and airflow inside the oven/range so the appliance can vent heat and combustion gases away from critical components. Restores proper internal venting and can reduce overheating or unusual odors. What it does:

• Channels exhaust from the oven cavity to the exhaust/vent path
• Helps protect wiring and components from excess heat
• Supports consistent oven temperature by allowing proper airflow
• Can address symptoms like hot spots, burning smells, or tripped safety limits when the original vent is damaged

• One tube vent assembly as shown

• Recommended for appliance technicians or experienced DIYers; disconnect power before starting
• Verify correct orientation and secure all fasteners and gaskets to prevent leaks
• Inspect adjacent parts and replace if damaged
• Follow OEM service manual steps for access and torque specs where applicable

This vent tube assembly routes exhaust air and helps direct airflow away from the appliance to maintain proper ventilation and operation. It replaces a damaged, cracked, or disconnected tube to restore correct air discharge. What it does:

• Channels exhaust airflow from the appliance to the external vent path
• Prevents air leaks that can reduce venting efficiency or cause mild odors
• Replaces tubes that are cracked, split, corroded, or otherwise damaged
• Helps maintain consistent airflow for proper appliance performance

• One vent tube assembly as shown

• Disconnect power (and gas if applicable) and unplug the appliance before beginning work
• Use appropriate tools and fasteners; do not overtighten clamps to avoid crushing the tube

This replacement tube vent routes exhaust from the appliance to the rear vent opening to help maintain proper airflow and reduce heat/smoke buildup in the cabinet area. It fits where the original vent tube was installed. What it does:

• Channels hot air and combustion byproducts safely away from the appliance cavity
• Helps restore proper venting when the original tube is cracked, bent, or missing
• Reduces heat transfer to nearby components and control surfaces
• Can stop symptoms like poor venting, unusual odors, or smoke accumulation near the appliance

• Turn off and disconnect power and gas before servicing; allow appliance to cool
• Use original hardware or OEM-recommended fasteners to secure the vent tube
• After installation, test appliance operation and check for proper venting and clearance

This vent assembly is the replacement exhaust vent that routes air from the appliance to the outside or to the internal ducting, restoring proper airflow and helping maintain efficient operation. What it does:

• Replaces a damaged, cracked, clogged or missing exhaust vent assembly
• Directs hot air and moisture away from the appliance to prevent performance issues
• Helps reduce unusual odors and poor venting caused by broken vent components
• Fits into the appliance's ventilation system to restore proper airflow

• One vent assembly

• Disconnect power (and gas, if applicable) before starting any repair
• Follow manufacturer diagram and instructions for proper alignment and secure mounting
• Inspect surrounding ductwork and seals; replace any damaged hardware or gaskets