General Electric Range / Cooktop / Oven Touch Pad

This repair doesn't require too much thinking, been a sticker you just have to take put the old one and stick the new one. Read more

I ordered the three parts listed and now my oven is beautiful, functional and like new again. I first had to figure out that the original parts are no longer available and had to perform an oven upgrade. Obviously the original design was flawed and the new design works perfectly and looks great! The whole repair cost was about $328 with shipping included. The parts were here in just a few days, about 2 to 4 days (some in two days, one in 4 days). Much cheaper and easier than replacing the... Read more

My wife put the faceplate on the oven control while I accessed the display by pulling the oven out, unplugged it, and removed the rear cover. Only three nut head screws held the upper back panel. 4 nut screws hold the display onto the oven, they were easily removed. My wife took a couple photos of the rear wiring to ensure we plugged the new oven control in properly (there are a fair number of wires but they are color coded in most cases). Turns out we didn't need the photo. As we pulled a... Read more

Ordered a new Faceplate Graphics, removed old faceplate and installed new. Required removing control panel with switches and display, including 10 screws to get to the faceplate. Faceplate has glue on rim, so had to peel off old faceplate, remove residue, then put on new. Not difficult, but reaching to remove the screws was a little challenging in a small kitchen. Now unit looks brand new! Read more

Ordered a new overlay and was extremely pleased with how fast I received it. Installed the overlay on the control board and the range is as good as new. Thanks again for your prompt delivery. Read more

A very common problem with the GE oven is the dreaded F7 error code. I purchased the control board as well as the keypad and replaced both. The error code could have been either part but since I saw a lot of grease, I chose to change out both even though I isolated the problem to the keypad only. By resetting the error first by hitting the clock button on the keypad, turning off the power,disconnecting the keypad, then turning back on the power if the code doesn't come back it's the keypad. ... Read more

Ordered the parts from Appliance Parts Pros, received within 5 days and replaced parts in less than 30 minutes. No problem with getting correct parts and fast. Read more

Got a replacement real fast delivery from you and exchange it fast and easy Read more

Ordered a new Oven Control unit and an Overlay (ours was punctured in a few places -- old and brittle). Opened the stovetop and removed some screws from the front control panel area. Followed the advice from Appliance Parts Pros' video to take a photo of the locations of all the connections on the old panel before removal -- that was an instrumental step to the success of this project! The whole job took just over an hour. Now the over controls and timers work like new -- because they are!... Read more

The oven control panel went in easily -- 4 screws to get access to it and four more to replace it. the panel does not include the face plate surface, but the existing plate can be removed from the control panel using a butter knife and re-used on the new panel. it holds on to enough of the stickiness. Read more

Control ovn kit Read more

First took apart my range control panel to review the possible failed component based on the flashing error code I was receiving. Found some insects inside the panel. Cleaned out but this did not work..possible short. Checked online with your chat service and they confirmed the two possible parts I may need. I ordered and replaced the most likely one and that did the trick. Part is working great and it did not take more than an hour to install. Read more

The entire control board was replaced. It was quick and easy! The entire repair took a total of 10 minutes, including testing. Be sure to order the new overlay, its permanently stuck to the face of the board. Read more

I unplugged the oven and then removed the back panel. Next I started started removing cables from the old control board one by one, being careful to plug them into the same place on the new board. There were some slight differences in where some cables were located, but the ports are labeled and you can just match it that way. Then I applied the new faceplate to the new control board. I unscrewed the old board and screwed in the new board. Very easy replacement. Read more

Replaced the whole Glass Touch Asm. Had to add spacer to bottom or else something was touching the circuit board and the touch screen would not work. Read more