General Electric Range / Cooktop / Oven Endcap Parts

Color: White. This is the right side end cap. For left side use WB07K10007.

Color: White. This is the left side end cap. For right side use WB07K10005.

This drum end cap supports the dryer drum and helps keep it aligned for smooth rotation. Replacing a worn or damaged end cap restores drum positioning to reduce rubbing, noise and uneven wear. What it does:

• Supports and locates the drum at the cabinet end to maintain proper alignment
• Helps the drum rotate smoothly and reduces rubbing or scraping sounds
• Prevents excess wear on the drum edge and adjacent supports
• Common symptom: noisy or wobbling drum that may rub against the cabinet

• One drum end cap

• Disconnect power to the appliance before beginning any repair
• Access typically requires removing the dryer front or cabinet panels; keep track of fasteners
• Inspect adjacent parts (glides, rollers, bearings or seals) and replace if worn
• Test the dryer on a short cycle after reassembly to ensure smooth drum rotation

This right-side end cover restores the finished trim and protects the exposed edge of the appliance where panels meet. It improves appearance and helps shield internal components from dust and contact. What it does

• Replaces a cracked, broken, loose or missing right-side end cover that leaves an exposed edge
• Provides a finished trim piece for a cleaner appliance appearance
• Helps protect internal components and wiring behind the panel from incidental contact and debris
• Keeps adjacent panels aligned and reduces movement or rattling at the cabinet edge

• Disconnect power to the appliance before beginning any repair
• Removal may require unscrewing or unclipping adjacent trim pieces; keep hardware for reassembly
• Align cover to the correct orientation (right side) and engage clips or fasteners fully before tightening
• If mounting hardware is damaged or missing, replace with OEM-specified parts for a secure fit

Color: Whie. This is the right side end cover. For left side use WB07K10002.

This right-side end cover is a molded replacement trim piece that restores the original appearance and protects internal components from dust and debris. It keeps wiring and fasteners concealed for a clean, finished look. What it does:

• Replaces a cracked, broken or missing right end cover to restore proper fit and finish
• Protects internal wires and components from dirt and snagging
• Prevents loose edges that can catch clothing or cause noise during operation
• Helps maintain the appliance's original alignment and panel spacing

• Disconnect power to the appliance before beginning any repair
• Typically installs with snap-fit clips and/or a small number of screws; handle clips gently to avoid breakage
• Inspect adjacent trim and mounting points for damage; replace if worn to ensure a secure fit

Color: White. This is the left side end cover. For right side use WB07K10001.

This left end cap is a direct-replacement trim piece that restores the finished edge and secure fit of the appliance door or panel. It helps maintain appearance and keeps adjoining trim and seals in place. What it does

• Covers and protects the exposed end of a door or trim piece to prevent sharp edges and wear
• Secures adjacent trim or retainer pieces so gaskets and panels stay aligned
• Stops drafts and reduces the chance of debris getting behind trim
• Common symptom: end cap cracked, loose, or missing causing visible gap or loose trim

• One left end cap

• Basic hand tools typically required; keep fasteners from the original part for reassembly
• Remove surrounding trim or door panel carefully to avoid damaging clips or gaskets
• Inspect adjacent trim and seals while installing; replace any damaged clips or screws as needed
• If work requires removing electrical panels, disconnect power first and follow manufacturer safety instructions

This end cap is a replacement terminal cover that protects and secures exposed connector ends on the appliance. It restores a finished appearance and helps prevent accidental contact with live terminals. What it does:

• Covers and protects terminal ends and wiring from contact and debris
• Helps maintain a secure connection by holding terminals in place
• Prevents shorting or arcing caused by exposed connectors
• Useful when the original cap is cracked, missing, or damaged

• Disconnect power to the appliance before servicing to avoid electric shock
• Verify fit and orientation before snapping the cap into place over the terminals
• If terminals or wiring are damaged, replace or repair those components before installing the cap

This right-side door end cap provides a finished edge and secure mounting point for the outer oven/stove door trim, restoring fit and appearance. Use it to replace a cracked, loose, or missing end cap and reduce rattling or gaps. What it does:

• Covers and protects the outer door edge while anchoring the trim for a proper door fit
• Restores the door's finished appearance when the original cap is cracked, broken, or faded
• Helps eliminate noise or vibration caused by a loose or damaged end cap
• Maintains alignment so the door trim and handle sit correctly

• Designed to install on the outer door edge; confirm right-side orientation before starting
• Remove door trim screws or clips as required; keep hardware separate and reuse if intact
• Use basic hand tools; avoid force that can damage surrounding trim or finish
• Disconnect power to the appliance and allow surfaces to cool before beginning work

Color: Black. Right hand side.

Color: Black. Left hand side.

This right-side end cap is a small replacement trim piece that restores a finished appearance and helps protect adjacent components from dirt and damage. It's a direct-fit exterior cap used on the refrigerator/dispenser assembly. What it does:

• Covers and finishes the exposed end of a trim or dispenser assembly for a clean look
• Helps keep dust, moisture and debris out of the gap behind the trim
• Prevents sharp edges or exposed fasteners that can catch or cause wear
• Commonly replaced when cracked, broken, warped or missing

• Disconnect power to the appliance before starting work when removal of electrical components is required
• Typically snaps or screws into place behind the trim; gentle prying may be needed to remove the old cap
• Inspect mating trim and fasteners for damage and replace if necessary