General Electric Range Parts

Replace your cracked, stripped, or missing oven thermostat knob. Mounts on the thermostat shaft for smooth temperature selection and control.

Replace your worn, cracked, or missing oven temperature control knob. Attaches to the thermostat shaft for precise temperature selection and adjustment.

Gas pressure regulator for ranges and ovens. Mounts to manifold to control incoming gas supply. Replace if cracked, leaking, or damaged threads.

Oven overheating or won't heat properly? This thermal limit switch monitors temperature and cuts power to prevent damage. Resets automatically when cooled.

Adhesive graphic label for your range's electronic control panel. Replaces worn, faded, or unreadable button markings. Restores a clean console appearance.

Fix an oven that won't heat or display that's unresponsive with this range electronic control board. Restores temperature control and timer functions.

Thermal insulation installs behind the oven liner to retain heat and protect surrounding surfaces. Replace when burned, contaminated, or damaged.

White front control panel for your range console. Restores clean appearance and secure mounting for controls. Replace if cracked, broken, or worn.

Secures the cooktop surface to the range chassis for stable alignment. Replace if bracket is bent, broken, or missing to eliminate looseness and gaps.

White plastic end cap for the right side of your range. Replaces old, yellowed, cracked, or broken trim pieces. Restores a clean appearance.

Replacement oven door handle for ranges. Restores secure grip and finished appearance when original handle is cracked, broken, or missing. Installs on door.

The Terminal Block is an OEM part for GE electric ranges. It serves as a critical junction point where the range's wiring connects to the heating elements, ensuring proper electrical flow and operation of the oven and cooktop. This component is essential for the safe and efficient functioning of your appliance.

Causes of a bad terminal block can include overheating due to electrical surges, corrosion from prolonged exposure to heat and moisture, or physical damage from improper installation or handling.

Symptoms of a bad terminal block include:

• The oven or burners not heating properly
• Visible signs of burn marks or corrosion on the block
• Electrical arcing or sparking
• Intermittent or no power to the heating elements

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

If your oven won't heat or displays error codes, the relay board may have failed. This assembly routes power to burners and heating elements.

Burner won't ignite, flame won't adjust, or gas leaks? This top burner valve controls gas flow to your range's surface burners. Moderate DIY repair.

This plunger switch is the push-style electrical switch that completes a circuit when an actuator is depressed, restoring reliable on/off signaling. Use it to replace a worn or broken plunger switch that causes intermittent or non-responsive operation. What it does:

• Closes an electrical circuit when the plunger is pushed, sending a signal to the appliance control.
• Commonly used where a door, lever or dispenser actuator must register a position or user input.
• Can correct symptoms like intermittent operation, a dispenser or mechanism that won't activate, or a stuck/unresponsive actuator.
• Acts as a direct mechanical-to-electrical interface—no electronics required.

• Disconnect power (unplug or turn off breaker) before servicing to avoid shock.
• Remove the access panel or housing to reach the switch; note actuator orientation before removal.
• Disconnect terminals or harness, then swap the old switch for the new one; reconnect terminals securely.
• Test the plunger action and appliance function before reinstalling panels.

This 9-inch dual radiant surface element kit replaces a failed burner on a smooth-top electric range or cooktop, restoring dependable, even heating and letting you choose a smaller or larger heating area to match your cookware.

• Provides two selectable heating zones (inner and outer rings) to match pot size
• Heats cookware evenly across the chosen zone on glass-ceramic cooktops
• Typical symptoms include no heat, only one ring working, slow or uneven heating, or intermittent operation
• Restores burner performance after internal failure of the element assembly

• Disconnect power at the circuit breaker before servicing; 240V shock risk
• Allow the cooktop to cool completely; protect the glass surface while working
• Photograph wiring and transfer leads one at a time to matching terminals on the new element
• Ensure the element seats correctly in its support brackets; test both inner and outer rings before final reassembly