General Electric Room Air Conditioner Parts

This axial flow fan moves air through the appliance to help cool internal components and support proper airflow. Replacing a worn or damaged fan restores quiet operation and helps prevent overheating-related issues. What it does:

• Circulates air across internal components or heat exchangers to maintain proper operating temperatures
• Helps prevent overheating of electronics, motors, or heating elements
• Reduces abnormal noise caused by worn or imbalanced fan blades or bearings
• Supports consistent airflow for reliable appliance performance

• One axial flow fan assembly

• Disconnect power to the appliance before starting any repair
• Handle the fan blades carefully to avoid damage; align properly during installation
• Verify secure mounting and electrical connections before restoring power
• Test appliance operation after installation and observe for proper airflow and quiet operation

This fan motor assembly replaces a worn or failed motor to restore proper airflow in your appliance. Designed to run the fan blade that circulates air for cooling, drying, or venting depending on application. What it does:

• Spins the fan blade to move air through the appliance for proper cooling, ventilation, or heat distribution
• Restores normal airflow when a burned-out or noisy motor causes weak airflow or overheating
• Reduces abnormal noises when a failing motor is the source of grinding, whining, or rattling sounds
• Helps prevent performance issues tied to poor air circulation, such as temperature inconsistencies

• Disconnect power to the appliance before beginning any service.
• Follow OEM disassembly steps; this motor may require removing a cover, fan blade, or mounting bracket.
• Handle the motor and wiring harness carefully; avoid pulling on wires and ensure connectors are fully seated.
• Replace or re-seat rubber grommets or brackets to reduce vibration and noise.

This bearing assembly supports the dryer drum and helps the drum rotate smoothly for quiet, even drying. Replacing a worn bearing restores stable drum movement and reduces noise and vibration. What it does:

• Provides a low-friction support surface for the dryer drum, helping it spin properly
• Prevents drum wobble and off-center rotation that can wear belts and rollers
• Reduces squealing, grinding, or rumbling noises caused by a failing bearing
• Helps maintain even drying by keeping the drum aligned

• Disconnect power and fuel (gas) supply before starting any repair
• Access typically requires removing the dryer front or rear panel and drum; refer to a model-specific repair guide
• Use proper tools and support the drum during removal to avoid damage
• Inspect adjacent parts (shaft, seal, rollers) for wear and replace if visibly damaged

This display board is the front electronic control that shows oven/range status and lets you select functions, times, and temperatures. Replacing a failed display restores visible readouts and responsive control inputs for safe, reliable operation. What it does:

• Provides the visual display and status indicators for the appliance control console
• Accepts user inputs from the control panel and relays commands to the main control
• Commonly replaced for blank or flickering displays, unreadable characters, or unresponsive console controls
• Can clear display-related error symptoms when the underlying issue is a failed display module

• Disconnect power at the breaker or unplug the appliance before starting work
• Access typically requires removing the control console or back console panel; follow OEM service instructions
• Handle the board carefully and avoid static discharge; do not touch connector pins
• If symptoms persist after replacement, check the main control and wiring harness for faults

This is the main control board that manages the appliance's electronic functions and user interface, restoring normal control of cycles, displays, and timed operations. Replaces a failed or unresponsive control module to recover device control. What it does:

• Receives input from buttons/knobs and sends commands to motors, valves, heaters, and displays
• Controls timing, cycle selection, and system diagnostics for normal operation
• Resolves issues like unresponsive controls, no display, or incorrect cycle behavior
• Requires correct configuration and secure connections to function reliably

• 1 main control board (electronic control assembly)

• Disconnect power before service to avoid shock or damage
• Handle board by edges and avoid contact with components or circuitry
• Verify mounting, connectors, and wire routing match original before restoring power

This is a replacement power cord that restores safe electrical connection to the appliance. Use it when the original cord is damaged or no longer supplying reliable power to help restore normal operation. What it does:

• Provides the main electrical connection between the appliance and household power
• Replaces frayed, cut, or melted cords that cause intermittent power or no power
• Removes loose or damaged plug connections that can trip breakers or cause arcing
• Helps eliminate visible burn or scorch marks at the cord or plug

• Always disconnect power at the breaker or unplug the appliance before servicing.
• Verify the cord routes through the strain-relief and is secured per the appliance's wiring harness.
• Inspect terminal connections for corrosion and tighten securely; match wire colors to original wiring.

This louver is a molded air vent piece that restores proper airflow routing and a finished appearance to the appliance. It replaces a cracked, broken, or missing vent louver to help protect internal components and maintain cabinetry aesthetics. What it does:

• Directs and channels internal airflow for even circulation
• Covers a cabinet or grille opening to protect internal parts from debris
• Replaces cracked, warped, or missing louvers that can rattle or look damaged
• Helps restore proper fit and finish on the appliance exterior

• One replacement louver

• Disconnect power to the appliance before beginning any work
• Inspect mounting tabs and clips; replace only if the OEM clips are present or available
• Usually secures with snap-in tabs or a few screws—use appropriate hand tools and avoid over-tightening

This thermistor is the refrigerator temperature sensor that helps the control board monitor and regulate cooling. Replacing a faulty sensor restores accurate temperature readings and consistent cooling performance. What it does:

• Measures internal refrigerator/freezer temperature and sends readings to the control board
• Helps the control board adjust compressor and fan operation for stable temperatures
• Can cause incorrect temperature display or uneven cooling when it fails
• Linked to excessive running, frequent defrost cycles, or poor cooling performance

• Disconnect power to the appliance before servicing to avoid shock or damage
• Handle the sensor and wiring harness carefully; avoid kinking or damaging the lead
• Ensure the connector is fully seated and any mounting clip or bracket is secured
• Some panel removal may be required; follow for access and reassembly