General Electric Wall Oven Touch Pad

The Faceplate is an OEM part for GE ovens. It is mounted on the front of the oven, covering the control panel area where the user interacts with the oven's settings and functions. 

Symptoms of a bad Faceplate include:

• Cracks or breakage that can expose internal components,
• Fading or peeling of finish, which affects the appearance and readability of the control labels,
• Loose fit that may interfere with the operation of control knobs or buttons.

Causes of faceplate damage typically involve physical impacts, excessive cleaning that degrades materials, or heat exposure that can warp or distort the plastic.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Wall Oven Faceplate is an OEM component for GE wall ovens. It provides the outer facade and aesthetic front panel for the oven. The faceplate is responsible for protecting internal components while allowing easy access to the oven cavity. 

Causes of a bad faceplate can include damage from impacts or repeated cleaning/scrubbing. Long-term wear and exposure to heat in the kitchen environment can cause discoloration or cracking of cheaper material faceplates over time.

Symptoms of a bad wall oven faceplate include:

• Cracks, chips, or broken areas in the material
• Looseness or inability to securely mount onto the oven 
• Gaps that allow visibility into or access to internal workings
• Issues opening or closing the oven door due to alignment problems

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This control panel overlay replaces the printed faceplate on the oven/range electronic control. It restores clear, readable button legends and a clean factory look while shielding the touchpad area from everyday wear.

• Provides the printed graphics/labels for buttons and display windows on the control panel
• Adheres over the keypad/control area to finish and protect the surface
• Typical replacement reasons: faded or worn text, peeling/bubbling film, cracks, discoloration, or damaged faceplate
• Addresses readability/appearance; electrical input or display issues usually involve the keypad or control board

• Disconnect power at the breaker before servicing
• Remove the control panel/backguard per your model's service information to access the overlay area
• Carefully peel the old overlay and clean adhesive residue; align the new overlay using the display and key outlines, then press firmly from the center outward
• Avoid touching the adhesive or stretching the film; reassemble the panel before restoring power

This part is a replacement control panel assembly. This part can be used to replace a broken or defective control panel in a variety of oven models. The control panel ensures the user can properly and safely adjust and maintain the oven temperature and settings. The appliance may not work properly, if at all, if this part is broken in any way. Thus, it will need to be immediately replaced. Always disconnect power from the appliance before starting any work or repairs. It is recommended that work gloves are worn to protect the hands.This is a genuine OEM part made by GE and has been sourced directly from the manufacturer. As an authentic replacement part, this control panel assembly is suitable for use on ovens that have been manufactured by General Electric, Hotpoint, and some other brands. This is a genuine part made of high-quality, durable materials and is sold individually.

Faceplate restores your appliance's control area by covering and protecting the electronic control board and buttons. It replaces cracked, dented or faded panel trim to improve appearance and help keep spills and debris away from controls. What it does:

• Covers and protects the control board and button assemblies from spills, grease and dust
• Restores the appliance's cosmetic appearance when the original faceplate is cracked, dented or faded
• Helps keep control buttons seated and prevents debris from interfering with switches
• Fits into the existing control housing using the original mounting locations

• Disconnect power to the appliance before beginning any repair
• Remove control knobs and the old faceplate to avoid damaging clips or wiring
• Handle edges carefully; replacement installs using the original screws/clips where applicable
• After installation, restore power and verify all controls operate normally; if controls do not respond, inspect the control assembly and wiring

This is the panel control tape ribbon assembly used to connect the console touchpad to the oven control electronics, restoring reliable button and display communication for the appliance control panel. What it does:

• Transfers signals between the touchpad/console and the main control board so button presses register.
• Replaces damaged, cracked or worn ribbon contacts that cause intermittent or non-responsive controls.
• Helps resolve issues like unresponsive keys, error codes tied to keypad faults, or sporadic display behavior.
• Flexible ribbon design lets it fit behind the control panel without bulky wiring.

• One panel control tape ribbon assembly as shown.

• Disconnect power to the appliance (unplug or shut off breaker) before starting.
• Handle ribbon contacts carefully—avoid sharp bends, creases, or touching conductive traces.
• Installation typically requires removing the front control panel or console; keep screws and clips organized.

The Graphics Assembly is an OEM part for GE wall ovens. Located at the front of the appliance, it serves an important cosmetic and protective function covering the control panel area.

Causes of a bad graphics assembly can include normal wear and tear over time from heat exposure and general use in the kitchen. Impact or handling damage during cleaning or maintenance may also affect parts.

Symptoms of needing replacement include: 

• Cracked or peeling graphics
• Loose or deteriorating mounting clips
• Discoloration or charring of the surface
• Missing buttons or graphics on the faceplate

This GE replacement faceplate is also compatible with Hotpoint, RCA and some Kenmore wall oven models. 

This panel and bracket assembly replaces the front control panel support and trim, restoring a secure mounting and finished appearance for the appliance. It helps stabilize the control area and keeps buttons, controls and wiring properly aligned. What it does:

• Provides the structural support and trim for the appliance control panel
• Keeps control components aligned and prevents panel movement or sagging
• Restores a finished appearance when the original panel is cracked, bent, or missing
• Helps reduce rattles or vibration caused by a loose or damaged bracket

• Disconnect power (unplug or shut off breaker) before starting any repair.
• Access typically requires removing exterior trim or the control panel; handle edges carefully — parts may be sharp.
• Save and reuse any screws or mounting hardware unless replacements are supplied.

The Overlay Panel Lower is an OEM replacement part for GE ranges. It covers the lower panel of the range, providing an attractive facade that protects the internal components. 

The overlay panel takes wear and tear from regular use and cleaning, so it's important for maintaining the aesthetic of the appliance. Over time, excessive heat exposure and harsh chemicals can cause damage like discoloration, cracks or chips to the panel.

Symptoms of a damaged overlay panel include:

• Appearance issues like scratches, discoloration or cracks in the surface
• Loose or sagging panel that no longer fits securely  
• Difficulty closing the lower panel securely

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.