General Electric Wall Oven Control Board

The Control Oven TO9 is an OEM part for GE ranges. This part manages the oven's various functions, including temperature regulation, cooking modes, and timer settings. It serves as the central interface for the user to control the oven's operations, ensuring precise and reliable cooking performance.

Causes of a bad control module can include electrical surges, general wear and tear, or physical damage from impacts or spills.

Symptoms of a bad control oven module include:

• Unresponsive or malfunctioning buttons and dials
• Incorrect temperature readings or inconsistent heating
• Display not functioning properly
• Oven not turning on or shutting off unexpectedly

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This electronic oven control board governs bake/broil power, temperature regulation, and the clock/display. Replacing a failed control helps restore accurate heating and responsive controls so your oven can run cycles reliably again. What it does

• Interprets keypad inputs to start/stop bake, broil, and clean cycles
• Regulates oven temperature using the sensor feedback and cycles heating elements via internal relays
• Powers and manages the clock, timer, and digital display
• Common symptoms include no heat, won't start, erratic temperatures, blank/garbled display, beeping, or control-related error codes

• 1 electronic control board (ERC3B)

• Disconnect power at the breaker before servicing
• Transfer wiring and mounting hardware from the original control one connector at a time; avoid bending pins
• Reuse your model's existing overlay/faceplate or keypad as required; seat ribbon cables fully and squarely
• After installation, set the clock and verify operation; the tech sheet for calibration if applicable

This electronic oven control board (ERC3HP) runs the oven's temperature, bake/broil functions, and display. Replacing a failed board restores accurate heating, clock/timer operation, and responsive controls so your oven cooks reliably again.

• Regulates power to bake and broil elements to maintain the set temperature
• Manages oven cycles, timing, and the digital clock/display
• Reads keypad inputs and switches relays to start/stop heating functions
• Common failure symptoms: no heat or erratic temps, blank/flickering display, unresponsive controls, or recurring error codes/beeping

• Disconnect power at the breaker before servicing; verify no voltage
• Handle the PCB by the edges and use anti-static precautions
• Photograph/label connectors; transfer wire harnesses and any brackets from the original board
• After installation, set the clock and run a test bake to verify operation

This electronic oven control board governs your range or wall oven's heating and display functions. Replacing a failed EOC restores accurate temperature control, reliable bake/broil operation, and responsive clock/timer performance.

• Regulates power to bake and broil elements using oven sensor feedback
• Controls set temperatures, preheat, and cycling to maintain heat
• Drives the clock, timer, and status indicators on the display
• Common symptoms: no heat or won't start, won't reach/set temperature, blank or unresponsive display, recurring fault codes

• Disconnect power at the breaker before servicing
• Handle the board by the edges and protect from static discharge
• Photograph wiring; move each connector to the matching terminal and transfer any mounting hardware from the original board
• After installation, run a test bake and verify temperature calibration per the unit's tech sheet

The board housing assembly mounts and protects the electronic control board inside the appliance's control console. Replacing a cracked or heat-damaged housing restores solid support, correct alignment, and reliable operation of the display and keypad.

• Supports and shields the electronic control board within the console
• Provides proper mounting and alignment for the display and keypad
• Helps manage and secure wire/ribbon connectors to reduce strain and vibration
• Typical indications for replacement: cracked or warped housing, broken tabs, loose or misaligned controls, sticking buttons, or rattling from the console

• Disconnect power at the breaker or unplug the appliance; verify power is off
• Remove the control panel/console to access the housing; note screw locations and photograph wiring
• Transfer the existing control board to the new housing; handle electronics with ESD care and avoid overtightening
• Reseat ribbon cables and harnesses fully before reassembly and restoring power

This OEM replacement part is an oven control board. The control board serves as the main computer to the oven and controls all its essential functions such as baking, maintaining temperature, as well as turning it on and off. If the oven is no longer turning on, or there is an error code on the digital display, this could mean that the control board is no longer operable. If this is the case, the control board will need to be replaced.To replace this part, start by unplugging the oven. After the power has been shut off, proceed to remove the upper back panel of the range. Once removed gain access to the old control board and snap it out of the locking tabs holding it in place. Take note of the orientation of the wires by taking a photo with a phone camera. Remove the wire harness and individual wires from the old board and place them into the correct terminals of the new board. Snap the new board back in place and re-install the upper back panel.This genuine replacement part is sold individually and is compatible with General Electric, Hotpoint, and RCA brand ovens.

This relay board assembly switches line power to the range/oven's heating circuits under the direction of the electronic control, helping restore reliable bake/broil operation when relays or board components fail. What it does

• Controls power to the bake and broil elements via onboard relays
• Executes low-voltage commands from the control to switch high voltage to the heating circuits
• Failure symptoms can include no heat in bake or broil, one element not working, or intermittent heating
• Burn marks or a stuck/clicking relay on the board may be visible indicators of failure

• 1 relay board assembly

• Disconnect power at the breaker before servicing; this board carries live voltage
• Access location varies by model; photograph and label all wires for correct reassembly
• Handle the board by its edges and observe ESD precautions
• Ensure all connectors are fully seated and the board is securely mounted before restoring power

This electronic oven control board manages the oven's heating functions, temperature regulation, and display/clock. Replacing a failed board restores accurate temperature control and responsive controls so your oven can heat and keep time reliably.

• Controls power to bake and broil elements based on user input and sensor feedback
• Regulates oven temperature and cycle timing
• Drives the display and processes keypad/selector inputs
• Common failure symptoms: no heat, won't start, blank/unresponsive display, beeping/error codes, inaccurate oven temperature

• Disconnect power at the breaker before servicing
• Handle the board with ESD care; avoid touching component contacts
• Note/photograph wire positions; transfer connectors one at a time and reuse existing brackets as needed
• After reassembly, restore power, set the clock, and test bake/broil per the service sheet

This electronic oven control board manages bake/broil power, temperature regulation, and the clock/display for the range. Replacing a failed control restores accurate heating, reliable cycle timing, and responsive keypad/display operation.

• Regulates bake and broil element power using feedback from the oven temperature sensor
• Controls oven temperature, cooking cycles, and timing functions
• Operates the clock, display, and keypad interface
• Typical failure symptoms can include no heat or won't start, won't reach/hold set temperature, blank/unresponsive display, or error codes/beeping

• Disconnect power at the breaker before servicing
• Handle the new board by the edges and use anti-static precautions
• Photograph wiring and move connectors one at a time; transfer any mounting brackets and the user interface overlay from the original
• After installation, set the clock and test bake/broil operation

This electronic oven control board manages temperature, bake/broil cycles, and the user display. Replacing a failed control can restore accurate heating and responsive controls when the oven won't start, won't heat properly, or shows error codes. What it does:

• Interprets keypad and temperature-sensor inputs to switch bake and broil relays
• Regulates preheat and maintains the set temperature throughout the cycle
• Controls the clock, timer, and oven display functions
• Help resolve: no heat, erratic temperatures, unresponsive or blank display, beeping or error codes

• 1 electronic oven control board

• Disconnect power at the circuit breaker before servicing; verify no power is present
• Use ESD precautions and handle the board by its edges to avoid damage
• Note/photograph wire locations and move connectors one at a time; do not force pins
• Reuse original mounting hardware; after reassembly, restore power and set clock—some models require configuration/programming per service instructions

This relay board assembly controls the high-voltage loads in a range or wall oven. It switches power to the heating elements and other oven circuits as directed by the main control, helping restore consistent, reliable heating performance. What it does

• Receives low-voltage commands from the electronic control and energizes bake, broil, and other high-load oven circuits
• Cycles elements on and off through onboard relays to help maintain set temperature
• Common symptoms of a failed board: no heat in bake or broil, only one mode heats, intermittent/uneven heating, or relay clicking with no element power
• Visual clues can include burnt spots on the PCB or heat-damaged terminals

• 1 relay board assembly

• Disconnect power at the breaker before servicing; this board carries line voltage
• Handle electronics by the edges and use ESD protection if available
• Label/photograph all wire positions; move connectors one at a time to the new board
• Inspect elements and wiring for shorts or heat damage before restoring power

Electronic range control that replaces the oven/range main control to restore timed cooking, display, and temperature functions. Fits as a direct replacement for failed or unresponsive electronic controls to get your range back to normal operation. What it does

• Replaces the oven/range main electronic control board that manages bake/broil cycles, timed cooking, and the user display.
• Restores clock and display functions when the control is blank, unresponsive, or shows intermittent behavior.
• Controls element cycling and temperature commands when the range won't heat or heats inconsistently.
• Can resolve erratic or intermittent oven operation caused by a faulty ERC.

• Always disconnect power at the breaker before starting any repair.
• Handle the control by its edges; protect the board from static, moisture, and impact.
• Match the part number and wiring exactly; transfer any existing mounting hardware or interface components as needed.

The Oven Control and Display is an OEM part for GE wall ovens and ranges. It is the central processing unit that governs all oven functions including temperature, bake/broil settings, timers and warming features. This control receives inputs from interior sensors, knobs and buttons to regulate heat accurately.

Causes can be failure of electronic components from prolonged use. Exposure to excess heat, moisture or spills over time also degrades control performance.

Symptoms of a bad control include:

• Inability to set or change oven temperature
• Timer and display errors or malfunctions
• Unresponsive knobs or buttons
• Failure to begin or end bake/broil cycles

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This oven control assembly is the electronic control board that manages oven functions, display and user inputs so your range can set and maintain cooking modes and temperatures. It restores control and display functionality when the original board fails. What it does:

• Receives commands from the touchpad/knobs and controls bake, broil, timers and oven lights
• Drives the front display and clock so settings and temperatures are shown correctly
• Sends signals to relays and safety circuits to energize heating elements and modes
• Common symptom fixes: blank or erratic display, unresponsive controls, oven not starting or failing to maintain temperature

• One oven control assembly (electronic control board)

• Disconnect power at the breaker before testing or installing to avoid shock or damage
• Handle the board carefully to avoid ESD or physical damage; do not touch exposed circuitry

This electronic oven control (ERC) is the main user interface and control board that manages oven functions and timing, restoring reliable cycle control and display feedback for affected ranges. What it does:

• Receives input from the touchpad/knobs and controls bake/ broil cycles, timers and display functions
• Regulates oven heating commands sent to the relay/line outputs (symptoms: oven won't heat or maintains incorrect temperature)
• Restores display/clock functionality and control responsiveness when the original board is faulty
• Can resolve issues like unresponsive controls, blank or erratic display, or error codes tied to the control electronics

• One electronic oven control (ERC) board

• Disconnect power at the breaker or unplug the appliance before servicing
• Handle the board carefully and avoid touching circuit traces or connectors; use ESD precautions where possible
• Follow the appliance service manual for access steps—installation typically requires removing the console or rear access panel and disconnecting ribbon/plug connectors

This control display module is the oven/range user interface that shows status and accepts touchpad or button commands, restoring visible controls and responsive operation for affected units. What it does:

• Displays oven settings, clock, temperatures and error codes so you can monitor cycles
• Receives keypad or touch inputs to set bake, broil, timers and other functions
• Helps the range respond when buttons are unresponsive or the screen is blank
• Can resolve intermittent control behavior or incorrect readouts related to the console

• One control display module (user interface) as shown

• Disconnect power at the breaker or unplug the appliance before starting
• Handle the glass and ribbon/pin connectors carefully to avoid damage
• Remove the console or trim to access the module; keep fasteners and grounding intact
• Verify the part number on your existing module before ordering and test operation after reconnecting power