General Electric Washer Dryer Combo Gasket & Seal

This exhaust gasket seals the dryer's exhaust duct connection to contain airflow and keep lint out of the cabinet. A tight seal helps maintain drying performance and efficiency while reducing warm, moist air leakage behind the unit.

• Seals the joint between the exhaust duct and outlet/blower housing to prevent air and lint leaks
• Helps maintain proper airflow for consistent drying results
• Wear or damage can cause longer dry times and warm, humid air or lint behind the dryer
• Visible tears, flattening, or missing sections indicate the gasket should be replaced

• Disconnect power; turn off gas supply for gas models before servicing
• Pull the dryer forward, disconnect the vent, and remove panel(s) as needed to access the exhaust connection
• Remove the old gasket and residue; clean mating surfaces; seat the new gasket evenly
• Reassemble, reconnect the vent, ensure the external vent is clear, and check for air leaks

This ring drain hose is the replacement drain tube that routes and removes water from the appliance, restoring proper drainage and preventing leaks or standing water in the wash area. Designed to match the original fit and function. What it does:

• Channels wastewater from the tub/pump to the household drain to maintain normal drain cycles
• Restores proper drainage when the original hose is cracked, kinked, or leaking
• Helps prevent leaks and water damage caused by failed or deteriorated hoses
• Compatible with compatible stock mounting points for a like-for-like replacement

• One ring drain hose (1 piece) as pictured

• Disconnect power and water supply before servicing to avoid shock or flooding
• Inspect adjoining clamps and fittings; replace clamps if corroded or damaged for a secure seal
• Ensure hose routing is free of sharp bends or kinks and is secured per the appliance's service instructions

This rubber agitator cap seal creates a watertight barrier at the base of the washer agitator to help prevent leaks and keep the transmission area dry. It's a simple replacement that restores proper sealing around the agitator. What it does:

• Seals the agitator base to reduce water entering the transmission and cabinet area
• Helps prevent leaks that can cause rust, puddling, or damage under the washer
• Keeps contaminants and detergent residue out of the gearcase area
• Supports consistent wash performance by maintaining a dry drive assembly

• Disconnect power and turn off the water supply before starting any repair
• Remove the agitator cap and agitator per your model's service instructions to access the seal
• Inspect surrounding parts (agitator cap, agitator, and shaft) for wear and clean mating surfaces before installing the new seal

This oven door gasket provides a replacement seal that helps keep heat and cooking odors inside the oven for consistent cooking and improved efficiency. It restores a tight seal where the door meets the oven cavity. What it does:

• Replaces a worn, torn, or brittle door gasket to reduce heat loss and hot spots
• Helps the oven reach and maintain set temperatures more consistently
• Minimizes smoke, burning smells, and excess energy use caused by leaks
• Improves cooking performance by restoring a proper seal around the door

• One oven door gasket

• Disconnect power to the range/oven before beginning any repair
• Allow the oven to cool completely; remove the oven door per the manufacturer's instructions if required
• Gasket typically attaches by pushing into a channel around the door or oven frame; use a non-marring tool if needed
• Follow OEM instructions for reinstallation and torque recommendations

This oil seal keeps appliance shafts and bearings sealed to prevent oil leaks and maintain smooth operation. It helps protect internal components and reduces the risk of lubricant loss that can cause noise or premature wear. What it does:

• Seals the shaft to keep oil and lubricant inside gearboxes or motor housings
• Helps prevent oil leaks that can stain belts, drums, or surrounding parts
• Maintains proper lubrication to reduce noise and wear on rotating components
• Commonly replaced when seals are cracked, hard, or leaking

• Disconnect power before servicing and follow all safety instructions for your appliance
• Inspect mating surfaces and bearing condition; replace damaged components as needed
• Use proper tools to press the seal evenly without distorting the lip
• Verify correct orientation of the seal during installation