Need Help?
Call or text
Show parts
This part is a replacement auger shaft bearing housing. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. This part can be used to replace a defective or broken auger shaft bearing housing in a variety of snow blower models. The auger shaft bearing housing is intended to cover and protect the equipment's hex bearing, which is located at the end of the auger shaft. This part will require replacement if corroded, dented, or damaged to the point of ineffectiveness. When working on or near an engine, it's important to ensure that the equipment is powered off and completely cool before beginning any repairs. For more accurate information on how and where to place this auger shaft bearing housing, the appropriate owner's manual and equipment diagrams should be referred to. As an authentic replacement part, this auger shaft bearing housing is suitable for use on snow blowers that have been manufactured by MTD, Craftsman, Troy-Bilt, and other brands. Please note that this is a genuine part made of high-quality, durable metal and is sold individually.
Usually ships within 4 - 14 days
The impeller on a snowblower is part of the system that sends the snow out of the machine and out of the path that is being cleared. The snow is pulled into the blower by the auger, which pushes the snow to the impeller. The impeller spins to send the snow on out the discharge chute. If the impeller stops working, the snow that is picked up will not be discharged, and the auger will stop working due to built-up snow. The easiest and most obvious way to diagnose a bad impeller is a lack of snow being discharged. If this happens, the impeller needs to be replaced. Remove the snowblowers bucket from the housing and then disassemble the belt pulley. Remove the screws from the auger carriers to access the auger and impeller assembly. Locate the screws and remove them to remove the assembly. Install the new impeller, then reassemble the snowblower with reversal of the steps. Start the snowblower to ensure that it works. This impeller is an authentic OEM replacement part sourced from the manufacturer for use in snowblowers. It is sold individually and does not come with attachment hardware. This impeller is designed for use in snowblowers manufactured by MTD, Cub Cadet, and Troy-Bilt.
This carriage bolt is a self-locking fastener made for use in round or square holes to attach metal to metal in outdoor equipment. These bolts provide an added safety feature because they can only be removed from one side. Carriage bolts can carry a large amount of weight, which makes them ideal for use in outdoor yard equipment. Carriage bolts may be used to attach a lawn mower's arm to the side support and other similar applications. If the bolt needs to be replaced, removal and installation are simple. Use a wrench to loosen the nut holding the washer and bolt in place. Once the nut is loose, the bolt can be unthreaded by hand and pulled out of the hole. To install, push the bolt back through the hole. If the fit is too tight to install by hand, use a hammer to tap it in place. Reinstall the washer and nut and tighten with a wrench.This carriage bolt is designed for use in lawnmowers, snowblowers, and lawn tractors manufactured by Craftsman, Bolens, Yard Machines, Yard-Man, and MTD. This is a genuine OEM product that comes directly from the manufacturer. Note: It does not come with a nut or washer.
This carriage bolt is a fastener with a flat tip and a round head with threading along the shank. Also known as coach bolts and plow bolts, the item can be used with many types of lawn and garden equipment. This is a 5/16 carriage bolt that resists turning after the bolt has been tightened. Wear and tear or impact can cause damage to a carriage bolt and lead to the need to replace them.Removing a carriage bolt requires twisting the nut loose from the end of the bolt and then hitting the nut with a hammer. This will begin to move the shoulder out of the lawn equipment. Continue the process until the bolt is loose enough to remove. Installing a new carriage bolt simply requires sliding the bolt into the hole, adding the nut, and tightening things up.This carriage bolt is designed for use with Craftsman, MasterCut, Toro, Yard-Man, Cub Cadet, Montgomery Wards, Ryobi, Huskee, Troy-Bilt, MTD, and Yard Machines lawn and garden equipment. It can be used with lawnmowers, chainsaws, snowblowers, edgers, and tillers. This is a genuine OEM product sourced directly from the manufacturer as an individual component.
The Hex Head Self-Tapping Screw is an OEM part for MTD outdoor power equipment. This screw is designed to securely fasten components of your equipment, providing reliable and durable connections. The thread size is 5/16 inches for major diameter, with 18 threads. The screw is 3/4 inches long and has a hexagonal or six-sided head.
Over time, the Hex Head Self-Tapping Screw can become damaged due to corrosion, stripping of the threads, or wear from frequent tightening and loosening. This can compromise the integrity of the connections and potentially lead to equipment malfunction.
Symptoms of a bad Hex Head Self-Tapping Screw include:
This OEM replacement part is designed for use with various models of MTD outdoor power equipment.
A carriage bolt is a type of fastener. It features a smooth rounded head and a square domed top. It has threading, which leads to up to the square shoulder. The purpose of its square is to prevent the bolt from spinning. Once the carriage bolt is inserted through the hole, using a nut and washer can provide additional security. Carriage bolts can corrode and loosen over time. Since it doesn't have a slotted head, a socket wrench is needed when replacing. This bolt carriage replacement is compatible with wood chippers, tillers, string trimmers, lawnmowers, and edgers. It is a genuine MTD product that measures 5/16x.075. It has a smooth rounded head and square shoulder underneath it. This carriage bolt is sold individually.
This carriage bolt is a genuine MTD part, sold individually. This carriage bolt can be used as a replacement part in a lawn mower or a snowblower. The purpose of the carriage bolt in a lawn mower or a snowblower is to serve as a fastening component.If the carriage bolt is dented, cracked, punctured, torn, scraped, warped, or eroded to the point of reduced or no functionality, the carriage bolt should be removed and replaced by this genuine OEM replacement part.This component is a genuine OEM replacement part sourced directly from the manufacturer. It is sold individually. This carriage bolt is compatible with the following outdoor appliance brands: MTD, Craftsman, Cub Cadet, Troy-Bilt, Murray, and Yard Machines.
The replacement screw seen here is made from high-quality, durable metal. It is an identical replacement for a faulty screw in many types of lawn and garden equipment. The screw features a hex-bolt shaped head and is used for various applications in the machines. Owners will want to refer to diagrams of their model to ensure the correct application for the screw. A screw may need to be replaced for any number of different reasons. In some cases, the screw could become lost when making other repairs to the machine. It could also become bent or the threads could be damaged. Corrosion is also a possibility over time. Replacing the screw is typically considered a fast and easy repair. The screw is a genuine OEM replacement part that is sold individually. The screw can be used for many models of snowblower, lawnmower, chainsaw, tiller, string trimmer, log splitter, edger, and wood chipper. Compatible brands include Craftsman, Cub Cadet, Troy-Bilt, Murray, Yard Machines, MTD, Huskee, Montgomery Wards, Bolens, Yard-Man, and MasterCut.
A flange nut's unique wide flange design distributes the nut's pressure over the part it is securing. In return, it creates an even fastening surface, which reduces part damage and nut loosening. This one-piece all-metal fastener has a lock nut version that features a protruding circular flange. This drastically increases bearing surface, compatibility either for irregular or oversized holes, and surface tension reduction. Flange lock nuts are the preferred type of fastener for many lawnmower models because it can provide better fastening than regular screws, which are known to loosen under extreme vibration. However, it’s important to know that flange lock nuts are susceptible to wear and tear due to constant vibration exposure. It is essential to replace the broken flange lock nut immediately to prevent serious damage to the lawnmower. The MTD 712-04063 Flange Lock Nut OEM replacement can be used with Craftsman, White Outdoor, Yard Machines, MTD, or Columbia lawnmowers. It is a genuine or OEM MTD replacement part that measures 5/16-18. It is threaded and requires the use of a wrench. This replacement flange lock nut is sold individually. An MTD bolt carriage may also be needed and is sold separately.
This is a flanged lock nut. It’s designed to apply tension, typically on a joint that needs to have a certain amount of flex. As such, it’s mostly used on snowblower chutes and lawnmower handles. They can remain in place, but with a forgiving connection that can take a beating. The nut size is 3/8, with a thread size of 16. A lock nut will generally last for many years. However, the silicone ring inside will wear down if it’s frequently tightened and loosened. It needs to be replaced when it will no longer reliably remain in place. Generally, this begins as a symptom of slight slippage and worsens as time goes on. Thankfully, whether it’s being used on a snowblower or a lawnmower, this nut is generally straightforward to access. Simply unscrew the old nut, then screw the new nut on until it’s nice and tight. Our flanged lock nuts are genuine OEM MTD nuts, and they are sold individually.
This flange lock nut is a metal component used in many types of lawn and garden equipment. It is the part that attaches to the rear wheel to keep it steady on any kind of terrain. It can also be used on handles and chutes for some equipment. The nut size is 3/8 and it has a thread size of 16. Most flange lock nuts will last for years. In some cases, the silicone ring inside the nut will wear down when it is loosened and tightened. When this happens, the flange lock nut will start to move around. It can start as minor slippage but often gets worse over time. It will need to be replaced but this is a simple task. Regardless of what equipment it is attached to, it simply needs to be unscrewed. Take off the old nut and replace it with the new one. This flange lock nut is an authentic OEM product that is sourced directly from the manufacturer. It is sold individually. The lock nut is made for use with lawnmowers, wood chippers, and edgers manufactured by MasterCut, Yard-Man, Bolens, Craftsman, Cub Cadet, Murray, Troy-Bilt, Yard Machines, MTD, and Huskee.
A cotter pin, also known as a hitch pin, is used to secure pins and shafts in place. Meant for snowblowers, riding lawnmowers, and lawn tractors, this bow-tie shaped cotter pin has a double-end design making it easy to pull or push through either side of a pre-drilled hole. This pin snaps into a locked position without tension, keeping it secure during operation. Designed for lawn and garden maintenance equipment, this part ensures secure fastening. If the power equipment is used frequently, cotter pins may have to be replaced regularly so it would be practical to keep extra bow tie cotter pins on hand. It is highly recommended that work gloves be worn during the installation of this part. This part is compatible with Craftsman, Cub Cadet, Troy-Bilt, Murray, Yard Machines, MTD, Huskee, Bolens, Yard-Man, and MasterCut brands of lawn mower, snowblower, and log splitters. This is a genuine OEM replacement part that is sold individually.
The roll pin, also called a shear pin, is a slender metal piece that fastens the driveshaft to the auger of a snowblower. This pin actually does double duty as a safety device. When moving through the snow-covered ground where objects cannot be seen, sometimes the snow-moving auger will come into contact with something other than snow. Since the driveshaft of the blower will continue to turn regardless of the mobility of the auger, the auger would be destroyed or significantly damaged upon encountering such an object. The roll pin is designed to shear off when the auger suddenly stops so the working parts of the blower are not damaged. Most blowers are designed so that the pins are easily accessible. By rolling the blower so the belly plate is up, it is easy to remove the belly plate and see where the shear pin goes through the driveshaft and connects with the auger. The broken piece of the old pin can be forced through by the new pin by gently tapping it with a hammer. This OEM genuine replacement part is compatible with a number of snowblowers, including Craftsman, Troy-Bilt, MTD, Yard Machines, and Yard-Man.
This spacer is a genuine MTD part that can be used as a replacement part for several different kinds of small engines, including lawn mowers, snowblowers, and wood-chippers. A spacer's function is to serve as a means to lengthen the distance between parts by fitting over a bolt or a screw to secure and maintain that distance. A reason to replace a spacer might be simply losing or misplacing the spacer itself, as it is small and can easily fall through cracks or unscrew itself over long periods of time. Other reasons include the gradual rusting, deterioration, bending, or cracking materials that can be attributed to general overuse or long-term exposure. If a spacer is subject to any of this kind of damage, it is best to replace it before using an appliance that requires a functioning spacer, as the malfunctioning spacer might cause permanent or serious damage. Always wear gloves when handling, repairing, and operating outdoor equipment. This spacer part is compatible with the brands MTD, Troy-Bilt, Yard Machines, and Yard-Man. This part is sold individually.
Washers are used in various locations on many types of lawn and garden equipment and can help to keep a bolt or screw in place. The washer will also help to spread the load from connection, which can help to reduce the risk of damage. One of the most common reasons to replace a washer is if the current washer is lost. If the washer is corroded or if it has been bent or otherwise damaged, it should be replaced, as well. Replacing a washer is generally easy, but this can depend on the location of the washer that needs to be replaced. The authentic OEM replacement flat washer is sold individually. Having several of these available for future needs is a good idea. The washer can be used on snowblowers, lawn mowers, tillers, edgers, log splitters, chainsaws, and wood chippers. Compatible brands include Craftsman, Cub Cadet, Ryobi, Troy-Bilt, Husky, Murray, Yard Machines, MTD, Huskee, Montgomery Wards, Bolens, Yard-Man, Turf King, and MasterCut.
This is an MTD flat washer for lawn and garden equipment. Flat washers are a standard piece of hardware typically used with bolts or screws to better secure components in place. If a flat washer is corroded or broken, or if it is missing, it should be replaced.To install a flat washer, simply slide it into place while reinstalling a screw or bolt. If working near an engine, ensure that the equipment is completely cool before installing this part.This is a genuine OEM part compatible with lawn and garden equipment manufactured by Craftsman, MTD, Cub Cadet, Troybilt, and Yard-Man. Washers are sold individually.
This hex screw is a genuine MTD part. It is a replacement part for lawn tractors, edgers, lawn mowers, snow blowers, tillers, string trimmers, chainsaws, log splitters, and wood chippers. It is a standard-sized part and it may be compatible with other machines as well.This particular screw is a one-inch metal screw and may be found in various places on the pieces of equipment. Refer to a parts diagram to find out where it is used on the equipment.This hex screw is a genuine OEM part sourced directly from the manufacturer. It is sold individually. Most machines have multiple screws; check others to see if more need replacement. It is compatible with several makes, including but not limited to Bolens, MTD, Troy-Bilt, Yard-Man, Yard Machines, Ryobi, Husky, Cub Cadet, Montgomery Ward, MasterCut, Turf King, and more.
The shear pin’s purpose is to stop the engine when it is broken. If the machinery hits something hard, the shear pin will break. This prevents injuries that could be fatal. If something large or small becomes clogged or jammed in the auger, the shear pin is meant to snap in half, rendering the auger useless. This happens once the auger reaches a certain point in pressure load, which also prevents damage to the rest of your equipment. The auger part of your machinery cannot turn without a shear pin. Since the purpose of the shear pin is to break on impact, it's a good idea to have several of these on hand for quick replacements. There’s nothing like having your equipment break down in the middle of a job. Repair is simple. Just remove the broken shear pin, line up the auger’s holes, and insert your new shear pin. Use the cotter pin to secure your shear pin. This genuine OEM auger shear pin works in conjunction with small engine equipment with augers made by Craftsman, Cub Cadet, MTD, Troy-Built, Yard Machines, and Yard-Man. This part is sold individually. Consider also ordering an MTD Pin-Bow Tie Cotter or retaining clip.
This replacement part is a flange bushing, and it is intended for use in different types of lawn equipment. This is a genuine replacement part made by MTD. This flange bushing is typically found in snow throwers but is compatible with other devices as well. The flange bushings are an important part of many appliances as they help reduce friction inside the machine. A new flange bushing might be needed if the current ones are broken or damaged in any way. It is common that different machinery needs multiple flange bushings. These small but important parts are placed around tubes or poles and are meant to assist during the rotating or sliding mechanisms. Be sure the machine is completely powered off and cooled down as the area with the bushings is often hot from friction. See the owner's manual for more exact instructions before attempting to replace this part. These flange bushings are sold as a set and are OEM replacement parts. These flange bushings are compatible with lawn equipment made by MTD.
This idler arm spacer is an authentic OEM replacement part sourced directly from the manufacturer for use on lawn tractors. The idler arm spacer attaches to the idler arm and creates a smooth surface for the idler arm to be able to move smoothly back and forth when in operation. The idler arm is part of the system that holds tension on the pulley and adjusts the belt. If the spacer is worn or missing, it will need to be replaced to keep the machine functioning efficiently. Before replacing the idler arm spacer, make sure the key is out of the ignition and that the spark plug is removed. Remove the deck belt and if necessary to access the idler arm, remove the deck. Remove the fasteners holding the idler arm in place and locate the spacer. Remove the spacer. Align the new idler arm spacer and place the idler arm back in place. Reassemble the deck and insert the spark plug.This idler arm spacer is a heavy-duty metal part that is individually sold. It is designed for use in lawnmowers and tractors manufactured by Craftsman, Murray, and MTD.
A flat idler pulley is a crucial piece of hardware designed for use with many different models of lawn mowers and snowblowers. It is compatible with products by brands such as Craftsman, Yard Machines, Yard Man, MTD, and Troy-Bilt.The flat idler pulley part is crucial for the proper functioning of the lawn mower because it connects to the idler bracket. The purpose of the flat idler pulley is to apply tension to the v-belt. The replacement process of the flat idler pulley will require a wrench.This flat idler pulley is made out of metal. It is sold individually. The flat idler pulley is an original OEM part sourced directly from the manufacturer, MTD.
This self-tapping screw is used to attach various parts to the engine housing of medium sized gasoline powered engines, in particular yard tools such as tillers, snow blowers, yard tractors, riding mowers, power vacuums, shredders, and chippers. It is used in over 150 different gasoline powered engines. Screws such as these are used particularly when a device is going to receive a great amount of vibration and stress while the engine is running and rotating tools are engaged. Such devices sustain a great deal of wear over time and the parts subject to replacement will eventually fail and need to be replaced. In such cases, it is wisest to replace the attaching hardware such as housing screws as well, because it is a self-tapping screw. Screws of this type are designed to forge a tight bond between the metal pieces they are securing together, but once loosened, they should ideally be replaced with new hardware. Make sure when replacing these screws to use genuine OEM parts like these screws. These replacement parts are manufactured to be identical to the original pieces. This hex screw is compatible with the following brands: MasterCut, Yard-Man, Yard Machine, Montgomery Wards, MTC, Murray, Bolens, Craftsman, Turf King, Troy Bilt, Cub Cadet, Huskee, Toro, and Ryobi.
This is a hi-pro key, or high profile key. This part is most commonly used to lock pulleys and gears into transmission shafts. Replacing a damaged, broken or lost hi-pro key is simple, requiring only a set of pliers to complete.This hi-pro key is an authentic OEM component sourced directly from the manufacturer. It is sold as an individual unit. It is compatible with lawn tractors and snowblowers from MTD, Ryobi, Yard Machines, Bolens, Yard-Man, Troy-Bilt, Cub Cadet, and Huskee. It is made of high-quality, durable metal materials.
In a snowblower, the driveshaft is connected to a part called a worm gear. The worm gear turns the auger blades which eject the snow. The worm gear is connected to the worm shaft, which causes the auger blade to turn rapidly. Eventually, the incredible torque inside the machine, plus the occasional bumps and bruises experienced by the machine in operation and when being stowed, may cause the worm gear to malfunction. When the snowblower is erratic in its operation and fails to remove snow completely, there is a good chance the problem is the worm gear. To replace the worm gear, remove the housing to get to the worm shaft. Remove the entire worm assembly. Next, remove the blower fan and remove the worm gear. Grease the auger assembly before installing the new gear. Reverse the order to reassemble. While the snowblower is disassembled, it's the best time so exam the auger, driveshaft, sheer bolts, and tires for wear. You may find other parts that need to be updated. Make sure to replace the worm bolt and any other necessary parts with a genuine OEM manufactured part such as this one. This gear can be used in a number of snowblowers, including machines made by Yard Machines, Craftsman, Bolens, Yard-Man, Troy-Bilt, Cub Cadet, Ryobi, Montgomery Wards, Huskee, and MTD. Part sold individually.
This is a replacement lawn tractor shaft worm. The shaft worm, also called a worm screw or vortex rod, is found in the lawn tractor's transmission. The shaft worm is a long shaft with spiral or helical threads on the other end. The shaft's threads will grab and turn a toothed gear. The overall purpose is to produce high torque multiplication and high reduction ratios. The shaft worm is able to reduce engine speeds medium/low engine speeds. When the worm shaft gear turns, it engages with a circular gear. This gear combination allows for a 90-degree transfer of motion. The two types of gears engage in a rolling or sliding action. These movements produce large amounts of friction. This friction creates heat that will, over time, cause the worm gear threads to become worn or damaged. With steel construction, this shaft worm is an OEM part that is sourced directly from the manufacturer. This part is designed to replace the damaged original shaft worm in MTD, Cub Cadet, Yard-Machine, Troy-Bilt, Yardman, Lawn Chief, Craftsman, Remington, Bolens, and Ryobi lawn tractors. The part is sold individually.
This oil seal is a genuine MTD part, sold individually. This oil seal can be used as a replacement part in a snowblower. The purpose of the oil seal in a snowblower is to seal off the space between components of the appliance through which oil might otherwise enter or contaminate components; this prevents oil leaks from the spots in which the oil seal is placed.The oil seal might have to be replaced if it can no longer effectively prevent oil leaks within the infrastructure of a snowblower. The oil seal could be subject to puncturing, tearing, ripping, warping, denting, or eroding over the typical use of a snowblower; if this occurs, the oil seal should be removed and replaced by this genuine OEM replacement part. It is a simple replacement process that will require only basic tools to properly execute.This component is a genuine OEM replacement part sourced directly from the manufacturer. It is sold individually. This oil seal is compatible with the following outdoor appliance brands: MTD, Cub Cadet, Troy-Bilt, and Craftsman.
This is a genuine oil seal made for use with a variety of snowblowers. It is part of the dipstick and ensures that oil stays inside the machine. In some cases, the oil seal can become worn out, be lost, or otherwise be damaged. When this occurs, it often causes the snowblower to start leaking oil. A visual inspection will determine whether the oil seal is in place or has been damaged. If it is lost or damaged, the oil seal should be replaced.A pair of work gloves and basic tools may be needed for this project. If the oil seal needs to be replaced, the first step is to turn off the snowblower and place it on a stable surface. Make sure the spark plug wire has been disconnected before proceeding. Access the oil dipstick and find the original oil seal. It can be removed so the new replacement part can be installed.This oil seal is an authentic OEM replacement part that is sourced directly from the manufacturer. It is made for use with several snowblowers by MTD, Craftsman, and Cub Cadet. This component is sold individually.
This is a carriage bolt, which is found on lawnmowers, snowblowers, and many other types of lawn and garden equipment. The carriage bolt is made of metal and the location will vary based on the model of the tool. The carriage bolt is used to fasten together two components on lawn and garden equipment. It can become damaged, break, or stripped and will need to be replaced.If the carriage bolt is broken, stripped, or has damage, a wrench will be needed to replace it. Make sure that the spark plug wire has been disconnected and the tool is turned off before you begin. Use the wrench to remove the carriage bolt before installing the new part in the same location. Replace any additional disassembled components removed to gain access to the bolt before using the tool.This carriage bolt is sold as an individual component. It is a genuine OEM replacement part that is sourced directly from the manufacturer. The bolt is designed to work with lawnmowers, chainsaws, snowblowers, tillers, and leaf blowers manufactured by Yard-Man, Bolens, Montgomery Wards, Huskee, MTD, Yard Machines, Husky, Troy-Bilt, Ryobi, Cub Cadet, and Craftsman.
Carriage bolts are flat-tipped with round heads, and their function in small engine appliances is to fasten together components and to secure that connection with a nut. There are various reasons that a carriage bolt might have to be removed and replaced, among them misplacement of the small, easily lost part. Other reasons to replace a carriage bolt could include damage or erosion that prevents the bolt from attaching the materials to one another effectively. If a carriage bolt is subject to this kind of damage, it should be replaced before using the small engine appliance. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This genuine MTD carriage bolt can be used as a replacement part for several different kinds of appliances that require small engines, including lawnmowers, snowblowers, wood-chippers, tillers, string trimmers, leaf blowers, and edgers. The OEM carriage bolt is compatible with the following brands: Craftsman, Toro, Cub Cadet, Ryobi, Troy-Bilt, Murray, Yard Machines, MTD, Huskee, Montgomery Wards, Bolens, Yard-Man, Turf King, and MasterCut. This part is sold individually.
This is a versatile screw designed with flanged hex head and double-lead threads. It is a high-low self-tapping screw with one thread that is high and the other low for easier penetration. The twin threads also reduce the amount of material displaced when the screw is driven into the material. This type of screw also creates a firmer grip. This screw can also be used to secure a newly installed front cover or grill. This part is available as an individual replacement part. It is a genuine OEM part for use with specific models of snow throwers, lawn tractors, electric mowers, chippers, and log splitters from Bolens, Cub Cadet, Craftsman, Poulan, Ryobi, Toro, MTD, Troy-Bilt, Yard Machines, and Yard-Man.
A flange lock nut, also known as a flange lock or a lock nut, is created to be used in various types of lawn and garden equipment. This flange lock nut holds other parts in place and, when properly threaded, will resist loosening. Over time, a flange lock nut may begin to weaken and may become loose or break. If it appears to be broken or weak, a replacement is required. Flange locks can be adjusted and uninstalled after use. When replacement is required, you may need a socket set, screwdriver, hacksaw, and butane torch. The socket wrench will loosen the bolt it is connected to, while the torch is used to heat the lock nut. A socket wrench may remove the nut, but sometimes cutting it with a hacksaw is required. This flange lock nut is a genuine OEM component directly from the manufacturer and comes in an individual unit. It is made of metal, a gold color, and can be found in various areas of lawn equipment. It works with lawnmowers, trimmers, snowblowers, cultivators, tillers, and leaf blowers by Poulan, MTD, Toro, Cub Cadet, Murray, Troy-Bilt, Bolens, Yard Machines, Craftsman, and Yard-Man.
A star knob connects the upper and lower handles on an outdoor appliance, and if removed, the upper and lower handles are quick-released. This part is made of black heavy-duty black plastic, and the threads are made of steel. Over time, the threading can become worn out, making the connection loose, and causing the two handles to no longer stay in place. Star knobs are a straightforward repair that can be done in a matter of minutes. Just unscrew the original, damaged knob and screw in the new knob. The knob is designed to be unscrewed by hand, so there is no need for additional tools to make this repair. This genuine OEM replacement part is designed for a variety of outdoor appliances, including lawnmowers, edgers, chippers, tractors, trimmers, and cultivators. This star knob is compatible with Yard Machines, Yard-Man, Cub Cadet, Bolens, Craftsmen, and Ryobi products. This part ships individually.
The replacement flat washer here is a part commonly found on many types of small engines, including those in lawn and garden equipment. The washer can be used on various parts of the engine depending on the make and model. The washer can help to spread the pressure of the connection over a wider surface area. This will help reduce damage to the machine at the connection point. The washers are made from metal and there may be a need to replace them. If they have become corroded, bent, or lost, they should be replaced right away. Owners should keep in mind what with some models, the washers will be secured with the use of a push pin. The push pins are sold separately. This is an authentic OEM replacement flat washer that is sold individually. The washer can be used on many types of equipment including lawn mowers, snowblowers, tillers, string trimmers, leaf blowers, edgers, log splitters, and wood chippers. Compatible brands include Craftsman, Cub Cadet, Ryobi, Troy-Bilt, Husky, Yard Machines, MTD, Huskee, Montgomery Wards, Bolens, Yard-Man, Turf King, and MasterCut.
This bell washer is a genuine MTD part, sold individually. This bell washer can be used as a replacement part for a lawn tractor, chipper shredder, tiller, or lawnmower. This bell washer adds spacing on a shaft in the tool.If the user of the appliance notices that a washer is missing, it should be replaced. General wear and tear is very normal for outdoor appliances, and if it occurs, the washer should be removed and replaced with this genuine OEM replacement part.This is an OEM part sourced directly from the manufacturer. It is sold individually. This bell washer is compatible with the following outdoor appliance brands: MTD, Yard Man, Yard Machines, and Troy-Bilt.
This part is a replacement flat washer. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. This part can be used to replace a damaged, misplaced, or defective flat washer in a variety of power equipment. Flat washers are a standard piece of hardware with many different uses. Their primary purpose is to increase the bearing surface area of a screw. This can help to prevent screws from becoming loose over time due to pressure that leads to them sinking into the surface. It is always recommended that the appropriate safety precautions are adhered to when attempting to fix any power tools or machinery. For more accurate information on how and where to install this flat washer, the appropriate owner's manual and included diagrams should be referenced.As an authentic replacement part, this flat washer is suitable for use on several different models of small engine outdoor power equipment manufactured by MTD, Murray, Craftsman, and other brands. This is a genuine part made of high-quality, durable metal and is sold individually.
This is a bushing made from black plastic with a cleft down the middle to provide enough flex for easy insertion. It has a flanged design, which means it won’t easily pop out after installation, even under stress from constant vibration. The bushing’s primary purpose is to protect wires and cables from damage as they pass through a channel. As such, the material is fairly durable and does not need to be replaced under ordinary circumstances. That said, there are some situations in which it can become damaged. For one thing, it’s easy to damage while repairing the wires or cables that run through the bushing. If the bushing does need to be replaced, it requires disconnecting any cables or wires that run through the bushing. Pop out the old bushing with a rubber mallet, install the new bushing the same way, reconnect the wires, and the repair is complete. This is an OEM part sourced directly from MTD, and it is sold individually. It was initially used on snowblowers but has also been used on lawnmowers and lawn tractors.
This is a chute crank bracket for a snow blower. The bracket holds and positions the chute in the proper direction so that snow is thrown at the desired angle. This is a genuine OEM part and is sold individually. This part is compatible with several brands, including Craftsman, Huskee, Ryobi, Troy-Bilt, Yard Machines, and Yard Man.If the crank bracket is rusted, damaged, or bent, it can affect the efficiency of the snow blower and throw the snow in the wrong direction or clog the chute. Replacing the bracket is fairly simple and will help the snow to be thrown efficiently and without clogging. For proper placement of the chute, remove it from the bracket and be sure that it moves easily. When attached, if the teeth do not mesh correctly, the bracket will need to be readjusted or replaced. This is easily done by loosening the bolts and moving the bracket until the teeth mesh. This will allow the chute to turn correctly. If the teeth will still not mesh, detach the chute and then remove the bad bracket and install the new bracket.