Hotpoint Range / Cooktop / Oven Parts

This fan assembly restores proper airflow inside your appliance, moving air to cool internal components and support ventilation. Replace a seized, noisy, or non-running fan to prevent overheating and bring back efficient, quieter operation.

• Circulates air through the appliance for cooling and/or ventilation
• Helps maintain safe operating temperatures and consistent performance
• Common symptoms: no or weak airflow, fan won't start or runs intermittently, loud grinding/squealing/rattling, excessive vibration
• A failed fan can lead to overheating or thermal safety shutdowns

• Disconnect power at the breaker before servicing
• Access the fan per your model's service information; note wire locations and mounting orientation
• Transfer any brackets, screws, or gaskets from the original
• Ensure the fan wheel spins freely and nothing contacts it before restoring power

This 8-inch surface burner element is the plug-in coil used on many electric ranges. Replacing a worn or failed element restores reliable heating and more even cooking performance on your stovetop.

• Provides heat to pots and pans when energized by the surface control
• Common fix for an element that won't heat or only heats partially
• Addresses visible coil damage such as breaks, blisters, or burned spots
• Corrects intermittent heating caused by an open or failing element

• Disconnect power to the range/unplug before servicing and ensure the element is cool
• Lift the old coil slightly, then pull straight out from the receptacle
• Inspect the receptacle/terminal block and drip bowl; replace if overheated or damaged
• Fully insert the new element terminals into the receptacle, seat the coil level, and test

This oven door hinge assembly controls the door's movement and keeps it sealed against the frame. Replacing a worn hinge restores smooth opening and a tight close, helping maintain temperature and consistent cooking performance.

• Provides spring-assisted pivot to support the oven door during opening and closing
• Maintains alignment and helps the door stay fully closed against the gasket
• Direct replacement for bent, weak, or broken hinges
• Common symptoms: door won't close fully, drops or slams open, sits uneven, squeaks, or allows heat to escape

• Disconnect power and allow the oven to cool completely before servicing
• Remove the door; engage hinge locks or insert hinge pins and support the door while lifting it off
• Springs are under tension—use caution and wear gloves/eye protection
• After replacement, check door alignment and gasket seal; many replace both hinges together for even operation

This replacement door handle restores a secure, comfortable grip on your appliance door. A worn or broken handle can make opening the door difficult and unsafe; swapping it returns normal operation and appearance.

• Provides the leverage needed to open and close the door smoothly
• Helps resolve issues like loose, cracked, or missing handle
• Improves safety by giving a stable handhold
• Restores original fit and finish when the old handle is worn or damaged

• Unplug power and let the appliance cool completely before starting
• Support the door and remove mounting screws from the interior side as applicable
• Transfer any end caps or trim pieces from the old handle if required
• Do not overtighten screws to avoid cracking the handle or door panel

This part includes replacement electrodes and a harness. This is a genuine OEM part made by General Electric and has been sourced directly from the manufacturer. This part is intended to replace damaged or defective electrodes on multiple models of gas powered stoves and ranges. These electrodes connect the spark igniters to the appliance in order to allow the gas cooktop to be ignited. If the spark igniters are not lighting, the electrodes may be the issue. Over time, electrodes can become worn or damaged and may require replacement. For safety purposes, always ensure the stove is completely disconnected from power and gas before starting the any repair work. Proper tools will be required to complete this process. Please make sure to follow appropriate safety precautions when attempting to repair any appliances. For more accurate information on how and where to install these electrodes and harness, the appropriate owner's manual and included diagrams should be referred to.As an authentic replacement part, this electrodes and harness kit is suitable for use on several different models of gas ovens, stoves, and ranges manufactured by General Electric and Hotpoint. This is a genuine part made of high-quality, durable materials and is sold individually.

This thermostat knob fits onto the oven's temperature control shaft so you can select and read the cooking temperature. Replacing a cracked or missing knob restores smooth adjustment and a clean, factory look on the control panel.

• Interfaces with the oven thermostat to set cooking temperature
• Pointer aligns with panel markings for clear, repeatable selection
• Common reasons to replace: cracked hub, stripped insert, missing or loose knob
• Symptoms include wobbling, slipping, not staying on, or unreadable markings

• Disconnect power and allow the oven to cool before servicing
• Pull the old knob straight off the thermostat shaft
• Align the new knob with the shaft and press firmly until fully seated
• Check pointer alignment with the panel markings after installation

A replacement spark ignition module that delivers timed high-voltage pulses to burner electrodes so gas burners light reliably. Replaces a failed ignition control to restore normal spark operation for cooktops and ranges. What it does

• Sends spark to the burner electrodes so gas ignites when a burner is turned on — use when burners fail to light or need multiple tries.
• Routes spark to the correct burner circuit based on the range's control settings.
• Helps prevent continuous sparking when the burner is off by switching ignition output as commanded.
• Works with existing electrode wires and control harnesses when the original module fails.

• Disconnect electrical power and shut off the gas supply before starting any work.
• Handle electrode wires and connectors gently; avoid crimping or bending electrode tips.
• Verify wiring matches the old module exactly; tag wires if needed to ensure correct reconnection.

This front orifice holder sits under the cooktop's front burner, channeling gas from the control valve through the orifice to the burner head. Replacing a damaged holder restores proper flame and dependable ignition on the front burner position.

• Channels gas from the valve to the burner head and secures the orifice spud in place
• Maintains correct alignment and seal for consistent flame size and distribution
• Helps resolve issues like front burner not lighting, repeated clicking without ignition, or weak/uneven flame
• Designed for the designated front burner position per the model's gas manifold layout

• Shut off gas supply and disconnect power; allow the appliance to cool before servicing
• Remove grates, caps, and burner head; lift or open the cooktop as required for access
• Transfer the existing orifice spud and mounting hardware to the new holder; tighten fittings and check with an approved leak-detection solution
• Test ignition and flame; adjust only per manufacturer instructions

This replacement oven door window glass restores a clear view into the cavity and the integrity of the door assembly. Install a new pane when the original is cracked, shattered, or permanently stained to maintain safe viewing during cooking.

• Provides the transparent viewing panel in the oven door
• Helps restore door integrity when used with existing trim and gaskets
• Replace for visible cracks, chips, shattering, or persistent staining/cloudiness
• Resolve rattling or loose window conditions

• Disconnect power and allow the oven to cool completely
• Remove the door and place it on a padded surface
• Wear cut-resistant gloves and eye protection; handle glass edges carefully
• Transfer any trim/brackets from the old pane; avoid overtightening fasteners and clean fingerprints before reassembly

Restore reliable lighting and heat in your gas oven with this glowbar igniter. When energized, it heats up to ignite the oven burner, eliminating no-heat and slow-preheat issues caused by a weak or failed igniter.

• Heats and glows to ignite the oven's gas burner
• Can glow without lighting the burner, or fail to glow at all
• May cause long preheat times or intermittent heating

• Disconnect electrical power and shut off the gas supply before servicing
• Allow the oven to cool completely; handle the igniter carefully and avoid touching the element
• Secure wiring and connectors away from hot surfaces; ensure solid connections
• Restore gas and power, then test for prompt, consistent ignition

The Burner Grate is an OEM part for GE ranges. It provides a stable surface for pots and pans on the stovetop, ensuring they remain securely in place during cooking. This grate is designed to withstand high temperatures and support heavy cookware, contributing to a safe and efficient cooking experience. The grate measures about 8-1/2 inches wide by 9 inches deep.

Over time, burner grates can become worn or damaged due to constant exposure to heat, spills, and heavy use. A compromised grate can affect the stability of your cookware and hinder proper heat distribution.

Symptoms of a bad burner grate include:

• Cracks or breaks in the grate
• Uneven or unstable surface for pots and pans
• Difficulty positioning cookware securely
• Visible signs of wear or rust

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This replacement thermostat knob mounts on the oven control shaft so you can select baking and broiling temperatures. Swap a broken or stripped knob to restore smooth, reliable temperature selection and a clean, finished control panel. What it does:

• Attaches to the oven thermostat shaft to turn the control and choose a temperature
• Provides the hand grip/interface for turning the oven on/off and setting temperature
• Helps ensure positive engagement with the control; a worn knob may slip or spin freely
• Common symptoms: knob cracked, missing, loose, or won't turn the thermostat reliably

• One oven thermostat control knob

• Disconnect power to the appliance before servicing
• Pull the old knob straight off the thermostat shaft; do not pry sideways
• Align the new knob's flat/D-shaped recess with the shaft and press straight on until fully seated
• Verify orientation (OFF/indicator alignment) and confirm the knob turns the control without slipping

• Designed for the oven thermostat control (separate from surface burner knobs on many models)

This surface element is the electric heating source for one cooktop burner. Replacing a failed element restores fast, even heat and dependable temperature control on your electric range or cooktop.

• Supplies heat to the selected surface burner when power is applied
• Restores consistent heating and proper cycling after element failure
• Common symptoms: burner won't heat, heats intermittently, or shows visible damage/hot spots
• Often tests open with a meter when failed

• Disconnect power at the breaker before servicing; allow the unit to cool completely
• Protect the cooktop surface; follow your service manual for access to the element
• Note wire positions; transfer wires to the same terminals and reuse existing mounting hardware
• Handle by the frame only; avoid touching the element surface. Reassemble and test operation

The Terminal Block is an OEM part for GE electric ranges. It serves as a critical junction point where the range's wiring connects to the heating elements, ensuring proper electrical flow and operation of the oven and cooktop. This component is essential for the safe and efficient functioning of your appliance.

Causes of a bad terminal block can include overheating due to electrical surges, corrosion from prolonged exposure to heat and moisture, or physical damage from improper installation or handling.

Symptoms of a bad terminal block include:

• The oven or burners not heating properly
• Visible signs of burn marks or corrosion on the block
• Electrical arcing or sparking
• Intermittent or no power to the heating elements

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Burner Grate is an OEM part for GE ranges. It provides a stable and durable surface to hold cookware above the burner, ensuring even heat distribution during cooking.

The burner grate should be replaced if it becomes damaged or worn out. Causes of a bad burner grate can include prolonged exposure to high heat, accidental impacts, or the enamel coating wearing off over time.

Symptoms of a bad burner grate include:

• The grate becoming unstable or wobbly
• Visible cracks or chips in the material
• Difficulty in positioning cookware securely
• Uneven cooking due to instability

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This broil drawer handle restores a safe, comfortable grip on your range's lower broiler drawer, making it easy to open and close. Replace a cracked, loose, or missing handle to keep the drawer operating securely and looking right.

• Provides a secure handhold for the lower broiler drawer
• Helps maintain smooth, aligned drawer movement during use
• Direct replacement for a broken, cracked, or missing handle
• Common symptoms: loose or wobbly handle, difficulty opening the drawer, or cosmetic damage

• Disconnect power and allow the range to cool completely before servicing
• Remove the broiler drawer if needed for access; retain the original screws/trim
• Align the new handle and secure with the existing mounting hardware
• Do not overtighten fasteners; verify smooth, secure drawer operation