Hotpoint Range / Cooktop / Oven Parts

Restore safety and appearance with this black oven door glass panel. It replaces cracked or shattered glass, bringing back a clear viewing window and the original finish when the exterior door glass has been damaged.

• Replaces damaged door glass to restore visibility and appearance
• Helps keep the door assembly secure when installed correctly
• Common symptoms: visible cracks, shattered/spidered glass, loose or rattling panel, cosmetic damage
• Color/finish: black

• Disconnect power and let the oven cool completely before starting
• Remove the door per your manual and place it on a padded surface
• Wear cut-resistant gloves and eye protection; handle tempered glass carefully
• Transfer any handle/trim as required and reinstall without overtightening fasteners

This surface burner control knob mounts on the valve stem and lets you turn the burner on/off and set flame level. Replace a cracked, stripped, or missing knob to restore smooth, precise control of your cooktop.

• Attaches to the burner valve shaft to regulate gas flow and flame size
• Replaces knobs that are cracked, stripped, loose, or missing
• Restores proper pointer alignment with the control markings
• Common symptoms: knob wobbles, slips, or falls off during use

• Disconnect power and allow the cooktop to cool completely
• Pull the old knob straight off the valve stem—do not pry against the control panel
• Align the flat/D shape of the stem and press the new knob straight on until fully seated
• If the control remains hard to turn or feels loose, inspect/service the valve before use

This line cord supplies electrical power from the wall outlet to the appliance. Replacing a worn, cut, or heat-damaged cord restores safe, reliable power and can help resolve no-power or intermittent operation issues.

• Delivers AC power from the outlet to the unit's electrical system
• Helps correct no-power or intermittent power when the cord is moved
• Ideal replacement for cords with cuts, fraying, or burn/discoloration on the plug
• Supports proper grounding and safe operation when installed correctly

• Disconnect power before servicing; ensure the appliance is fully de-energized
• Match wire routing and connections to the product's wiring diagram; ensure a secure ground
• Use an appropriate strain relief if required by the product to prevent abrasion
• Route the cord away from sharp edges, moving parts, and hot surfaces

This 8-inch coil surface element restores consistent stovetop heating on electric ranges. Replace a warped or burned-out burner so pots heat evenly and your everyday cooking temperatures are easy to reach and maintain.

• Converts electrical power into heat for the 8-inch cooking zone
• Plugs into the surface-element receptacle for a secure power connection
• Common fix for a burner that won't heat or heats slowly/unevenly
• Replace if the coil is blistered, warped, or the terminals are burnt/pitted

• Disconnect power at the breaker or unplug the range; allow the element to cool completely
• Lift the old element slightly and pull straight from the receptacle; remove from the support
• Inspect the receptacle; replace the block if terminals are burnt or loose
• Align the new element in the drip pan/support and push terminals fully into the receptacle until seated

The HV Electrodes and Harness Assembly is an OEM part for GE gas ranges. It transmits high-voltage electricity to strategically placed components.

Symptoms of a bad HV electrode and harness include: 

• Unpredictable or incomplete heating within oven cavity sections   
• Error codes related to HV delivery issues preventing bake/broil
• Frayed, loose, or water-damaged wiring presenting shock hazards

Causes involve normal wear to materials transmitting continuous high voltage. Exposure to condensation or food spillages can damage insulation prematurely as well.

This part is also compatible with Hotpoint, RCA, and select Kenmore models.

This silicone gasket creates a flexible, heat-resistant seal in range and oven assemblies. Replacing a deteriorated seal helps contain heat and moisture at joints and trim areas, protecting internal components and restoring proper fitment.

• Forms a durable, high-temperature seal between designated mating surfaces
• Helps prevent heat, steam, odors, and spills from escaping at seams
• Can help address visible gaps, leaks at edges, or looseness around trim/panels
• Restores the manufacturer-specified seal after service on affected components

• Disconnect power and allow the appliance to cool; turn off gas if applicable
• Remove old gasket/sealant and clean surfaces thoroughly; dry completely
• Position/install exactly as directed for your model; avoid stretching or over-compressing
• Follow model/service instructions for any required cure or set time before heating

This LP conversion kit reconfigures a compatible gas appliance from natural gas to liquid propane. Using the manufacturer-specified setup helps ensure proper fuel flow, correct flame characteristics, and safe performance when operating on propane.

• Converts the appliance for propane service by setting gas pressure and burner fuel metering for LP
• Required when installing a natural-gas-configured unit in a location with propane supply
• Helps achieve proper flame size and color after switching fuel type
• Helps prevent poor combustion and soot related to an incorrect fuel setup

• Follow manufacturer instructions and local codes
• Disconnect electrical power and shut off the gas supply before beginning
• Adjust the gas pressure regulator for LP and change specified components as directed
• After conversion, leak-test all connections and verify burner operation and flame quality

Color: White. It measures about 2 inches in diameter.

This gasket creates a tight seal between mating parts in your appliance, helping prevent air, heat, moisture, or combustion byproducts from escaping so the unit runs safely and maintains proper performance. What it does:

• Provides a secure seal between components to prevent leaks
• Supports stable temperatures and airflow inside the appliance
• Minimizes odors, heat escape, and drafts around the sealed area
• Typical failure signs include cracks, flattening, fraying, or persistent leaks

• Disconnect power and, if applicable, shut off gas; allow the unit to cool completely
• Remove retainers/fasteners, take out the old gasket, and clean the mating surfaces
• Position the new gasket without stretching or kinking; align edges/holes and reassemble
• For gas models, perform a leak check with a soapy water solution after reassembly

Color: White

Color: White

This gas pressure regulator reduces and stabilizes the supply gas to the appliance's manifold, helping ensure steady burner flames and safe, consistent heating. Replacing a faulty regulator can restore reliable ignition and oven performance.

• Reduces incoming line pressure to the specified manifold pressure for proper burner operation
• Maintains consistent flame height and heat output across burners
• Helps address flame surging or fluctuation when other gas appliances in the home turn on

• Turn off gas supply and power before servicing; installation by a qualified person is recommended
• Follow the flow-direction arrow on the body and ensure proper mounting orientation
• Use approved pipe thread sealant on NPT threads only; do not use sealant on flare connections
• After installation, leak-test all joints with a non-corrosive solution and verify burner operation/manifold pressure per the service manual

This 6-inch coil surface element restores the small burner on your electric range. It plugs into the burner receptacle to deliver dependable heat for everyday cooking when the original coil is damaged or no longer heating.

• Heats the 6-inch cooktop position by converting electrical energy into heat
• Direct plug-in coil design for the element receptacle; no rewiring when replacing like-for-like
• Common fix for a burner that won't heat, heats unevenly, or works intermittently
• Replaces coils with visible hot spots, blisters, breaks, or corrosion

• Disconnect power at the breaker and allow the surface to cool completely
• Lift the old element straight up and out of the receptacle; remove the drip bowl if present
• Inspect the receptacle and wiring for discoloration or looseness; replace if damaged
• Align and firmly seat the new element's terminals; ensure the coil sits level in the bowl

Replace a cracked, shattered, or heat-damaged inner oven door pane with this heat-resistant glass. It restores proper insulation and visibility, helping your oven maintain temperature and protecting the door assembly from spills and high heat.

• Replaces the interior pane within the oven door assembly
• Helps retain heat for consistent cooking performance
• Shields the door liner and insulation from spills and steam
• Common signs it's needed: cracked/shattered inner glass, missing or loose pane, heat escaping, or the door exterior feeling hotter than usual

• Disconnect power or turn off gas and allow the oven to cool completely
• Remove the door per your model's instructions and place it on a padded surface
• Wear gloves; handle glass by the edges and avoid overtightening retainers
• Transfer any brackets, trim, or gasket from the original pane if your model uses them; before reassembly

This leveling leg is an authentic OEM replacement part sourced directly from the manufacturer. Leveling legs are used on the bottom of stoves to correct imbalances on the cooking top caused by floors being unlevel. The leveling leg is threaded so that it can be adjusted up or down as needed. There are four holes for leveling legs on the stove's bottom. Each leg can be adjusted independently. If the legs are missing or lost, these replacements will help level the stove for more even cooking. When the stove is not level, the food inside pans will be unlevel and not cook evenly.Make sure the power is disconnected before installing the leveling leg. Tilt the stove back and place a chock underneath one side so that the leg can be screwed up or down as needed. Remove the chock and check for level. If the stove is still unlevel, repeat the procedure on the side that is not level. Continue to adjust until the stove is level. Restore the power to the stove.This leveling leg is a black part that is sold individually. It is designed for use on ranges manufactured by General Electric, Kenmore, and Hotpoint.

Replacement oven temperature control knob that mounts on the thermostat shaft. Restores smooth, accurate temperature selection when the original knob is cracked, stripped, loose, or missing, so you can reliably set your oven for baking or broiling.

• Attaches to the oven thermostat/control shaft to set cooking temperatures
• Replaces cracked, broken, missing, or loose knobs that spin without turning the control
• Restores proper pointer alignment with OFF and temperature markings
• Provides a secure, smooth-turning grip for everyday use

• Turn the appliance off and allow it to cool; disconnect power before servicing
• Pull the old knob straight off the shaft—do not pry against the control panel
• Align the flat/keyed side of the new knob with the shaft and press on firmly
• Test through temperature settings