Ikea Range / Cooktop / Oven Parts

Replaced the latch. Everything works fine now Read more

Removed the element "easy just four screws" unplugged two connecting wires, removed element. Did a "continuity test" on element, it failed, so I ordered a new one and installed it. It works great now. Read more

The problem was partly caused because the original legs were at full extension. The replacement legs were longer than the originals and were more secure at the needed length. One difficulty was that the threaded base plate where the legs screwed in had been damaged and had to be reshaped, I was able to reshape the sockets with some effort, to allow the legs to thread in, though one remained slightly angled. (A metal tool of some type which could be threaded in and used to bend the socket area... Read more

The problem is a finicky ignition system, Direct Spark Ignition. Apparently Whirlpool redesigned the igniter/burner assembly slightly to make it more reliable. The repair is very easy. Turn off power, but you don't need to turn off gas. Remove oven bottom and flame spreader, then remove burner/igniter assembly, one screw at front, one at back. Lift out burner assembly carefully to avoid stretching wire. Pull electric connector from pin on burner/igniter assembly. Vacuum to clean oven. ... Read more

I purchased 2 new light rocker switches, Because the heating element rocker switch was unavailable. First I removed the power source for safety. Then I simply pulled each switch out individually with a flathead screwdriver for leverage. I simply unplugged the wires from the old rocker switch, discarded the old rocker, plugged the wires into the new rocker switch, and pushed the new switch appropriately back into the control panel. I used the same steps for both rocker switches. Once... Read more

I knew for sure that the hinge with the large spring was damaged, but elected to replace both hinges and receivers. Replacing the parts was fairly easy and would have taken me less then an hour. This model has thin metal covers over the hinge assemblies. I found that squeezing in the sides of the covers help to hold them in place on the hinge while reassembling the door. My only difficulty was putting the door back on the oven. It took a little maneuvering but I managed to get it. Now the door... Read more

• Element will not heat

Purchased a new Element surface and installed same... All Okay now... Read more

It was a simple process to enter the model number of our glass cook top stove; learn the part number required and order. It arrived in 2-days -- least expensive shipping method. The cooktop was removed with a Phillips-head screwdriver by 4 small sheet metal screws on the right and left side of the oven. The oven's power to the cooktop was easily disconnected via two "clips" and one ground. Would have cost way more with an appliance repair shop and it's an easy do-it-yourself repair. Read more

Only the lower element was burned out, but I opted to replace both. Ordered from AppliancePartsPros and received them very quickly! A few screws, unplug and plug in the new elements, replaced the screws, and DONE! This has to be one of the easiest repairs a homeowner can do. Thanks, AppliancePartsPros for carrying the original equipment parts and providing the fast shipping! Read more

Easy just pull clip and put back Read more

Just removed the old glass top which consisted of removing 6 screws Read more

I purchased a burner and a oven orifice replacement kit from Appliance Parts Pros. I downloaded an installation manual from Whirlpool and followed the instructions. It was pretty easy. The front burner orifices could be replaced by just taking off the burner cover. The back ones required removing the burner diffuser. You will need to reattach the back burner bottom assembies after you remove the diffuser before you unscrew the orifice or it might bend the burner piping causing it to not line up... Read more

I watched the AppliancePartsPros video on youtube and ordered the glass. It arrived in two days and took 20 minutes to install. Read more

Replaced the control that I think was bad from the purchase of the stove new as the burner didn’t throttle as is does now. Read more

• Little to no heat when broiling

I wanted to get the upper oven baking element replaced; it hasn't been working for a few months. This double oven has had two other issues, there is a fan that comes on to cool the electronics panel, That fan has made excessive noise and it operates for 2-3 hours after the oven turns off. The other problem with the oven is the Self-Cleaning feature runs for about 15-30 minutes and then turns off with an error code. I've had a local appliance repair person in to address the error code and... Read more