Jenn-Air Range Parts

This spring element support secures and stabilizes a range or oven heating element to keep it properly positioned for consistent heating and safe operation. It replaces a worn or broken support that allows an element to sag or vibrate. What it does:

• Holds the bake/broil heating element in the correct position so it heats evenly
• Prevents the element from sagging, touching the oven cavity, or rattling during use
• Helps maintain correct element clearance to reduce arcing and uneven cooking
• Addresses symptoms like a loose or wobbly element, unusual noises, or intermittent heating

• One spring element support

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Handle the heating element and support carefully to avoid bending or damaging the element
• Verify correct part orientation against the oven's wiring diagram during installation

This switch harness assembly connects the control panel switches to the appliance's main wiring, restoring reliable electrical connections for panel buttons and cycle selection. It replaces a damaged or worn harness to help regain consistent control response. What it does:

• Routes power and signals between the control switches and the main control board
• Replaces frayed, broken, or corroded wiring that can cause intermittent or no response from panel buttons
• Helps resolve symptoms like unresponsive controls, intermittent operation, or no-start conditions linked to panel wiring
• Maintains original connector fit and routing for correct switch function

• One switch harness assembly as shown

• Disconnect power (unplug or switch off breaker) before starting any work
• Handle connectors carefully and match connector shapes; do not force or modify terminals
• Verify routing and secure clips to prevent rubbing or pinching against moving parts

This orifice holder secures the 5K gas orifice in place on compatible gas burners, keeping the orifice aligned for consistent flame performance and safe operation. It's a small but essential mounting component. What it does:

• Holds the 5K orifice firmly at the burner connection to maintain correct alignment
• Helps ensure consistent gas flow to the burner for steady, even flames
• A damaged or loose holder can cause a weak, uneven, or intermittent flame
• Works with the burner assembly to support reliable ignition and heat output

• One orifice holder (5K) as shown

• Turn off gas supply and power to the appliance before servicing
• Access may require removing the burner cap and grates or front panels
• Handle small components carefully; keep track of fasteners and orientation

This control switch is the user-facing rotary selector that lets the appliance select cycles and settings. It restores clear, tactile control so the unit responds correctly when you turn the knob. What it does:

• Selects operating cycles and settings when the knob is turned
• Routes electrical signals from the control panel to the selected function
• Commonly replaced when settings do not change or the control feels loose/slips
• Resolves intermittent or unresponsive cycle selection and erratic behavior

• Disconnect power before attempting any repair to avoid electrical shock
• Accessible from the control panel; remove trim or console as needed per your model's service instructions
• Test function after reassembly; do not force the selector or use excessive torque

This orifice spud directs gas flow into the burner for consistent ignition and flame control. It restores proper burner performance so cooking heats evenly and burners light reliably. What it does:

• Seats the burner orifice to control gas flow to the burner
• Helps maintain a steady, even flame for consistent cooking
• Can resolve weak or uneven flames and burners that struggle to light
• Works as the sealed interface between the gas manifold and burner tube

• One orifice spud

• Turn off the gas supply and disconnect power before servicing
• Inspect surrounding seals and gaskets for damage and replace if necessary
• Use basic hand tools; avoid overtightening to prevent damage

One knob per each package. Please order additional knobs if needed.

This bezel knob replaces a worn, cracked or missing control knob bezel to restore a clean finished look and reliable control feel. It provides the tactile grip needed to select settings easily. What it does:

• Covers and protects the control shaft while providing a gripped surface for turning and selection
• Replaces cracked, faded or broken bezels that make controls hard to use or look worn
• Restores proper alignment and tactile feedback for accurate setting selection
• Matches the original black finish for a consistent appearance

• Always disconnect power (and gas when applicable) before servicing controls.
• Most installs simply pull the old bezel off and push the new one onto the control shaft—align splines before seating.
• If the control shaft or switch is damaged or loose, replace the underlying control assembly rather than forcing the knob.

Replace a damaged or unsteady cooking surface with this burner grate. It supports pots and pans at the proper height above the burner, restoring stable, level support on your gas cooktop or range when the original grate is worn or broken.

• Provides sturdy support for cookware over the surface burner
• Maintains the correct clearance between burner and pan for consistent heating
• Replaces grates that are cracked, bent/warped, or have worn feet causing wobble
• Helps prevent rocking or instability of pots and pans during cooking

• Allow the cooktop/range and grate to cool completely before handling
• Lift off the old grate; clean the surface; align and place the new grate over the correct burner
• Ensure the grate sits flat and stable—do not force into place
• Refer to your owner's manual for care and cleaning recommendations

Color: Black

Color: Stainless

This speed nut is a stamped metal retaining clip designed to hold screws or fasteners securely to appliance panels and trim. It provides a simple, vibration-resistant connection that keeps covers and components in place. What it does:

• Secures screws to thin sheet metal or panel edges where a threaded hole isn't available
• Provides a firm, vibration-resistant attachment for panels, trim, or small components
• Helps prevent screws from loosening or backing out during normal use
• Commonly used where a captive nut or clip is required for assembly or repair

• One speed nut / retaining clip

• Disconnect power and unplug the appliance before starting any repair
• Position the clip over the panel edge or hole so the screw can engage the clip's thread; press or tap gently until seated
• Use the correct screw size and avoid over-tightening to prevent deforming the clip or striping threads
• Wear gloves and eye protection when handling sharp sheet metal edges