Jenn-Air Washer Parts

Went on internet, found a great site and learned that the cold water hose filter was very much clogged at the machine intake. Cleaned it and voila. Ordered an extra filter from Appliance Pros.com and literally was amazed that it arrive within 2 days of my internet order. Great efficiency and customer service….great experience. Will definitely use them in the future….thank you! Read more

Acualy sounded and looked major but with a littel help with you tube the job only took 30 minutes. 3 bolts for the water pump pulley broken pulley poped off new one klick into place simple belt install good to go. Parts saved me $40 and where here in only 2 days. I couldnt be happyer. Read more

• Shakes and moves

New leveler pads Read more

• Shakes and moves

Took off the old parts and replaced with the new parts Read more

This was some repair! My SG1000 stackable is over 30 years old and was purchased second hand. I've replaced many parts in the dryer section, but besides a water inlet, this was my first repair to the washer. All of a sudden it started making a terrible noise and was not agitating the clothes. The spin cycle worked fine. I first replaced the two belts on the bottom, but when I removed the old ones I realized they did not look terribly worn and weren't the cause. Many stories on here indicated... Read more

Replaced dried crumbling rubber foot. Cleaned inside and outside of dryer before installing igniter cleared vent hose. Leveled unit installed dryer igniter. Fired it up.Runs Great Now. Read more

Found the wonderful parts diagrams you most generously share online and a couple of YouTube videos . I determined it should be repairable. In my cast the agitator shaft was frozen (rusted) in place. I was very fortunate to have been able to eventually remove it with the use of a lot of BP penetrating oil and heat. Long and short the replacement parts fit perfectly and the washer is running like new. Special thanks to the online support make my repair possible. Read more

I figured it had to be the flume; changed the flume and hose, mounting screws Read more

Replaced It With New One Read more

Purchased the triple burner and dual burner element. I added my model of stove and I was able to pull up diagrams of the stove parts. The parts were easy to find using the diagrams and the burner elements were marked 17 & 15 so I placed my order. Parts were here in a couple of days. The tricky part was figuring out how to get into the stove top. I was a few youtube videos to see different replacement. My husband and I got the stove top off and flipped it over on the counter. We looked at... Read more

I changed both the Control Panel and the Oven Control Board. Since I had previously changed the Oven Control Board, this was a fairly quick fix. I was also able to change out one of the Indicator Lens that had been broken. Read more

I followed the Appliance Parts Pro's advice videos for the Maytag MAV6451AWW Atlantis washer on replacing the snubber ring and the suspension springs. Everything went just fine except replacing the two rear most suspension springs. None of the videos illustrated REINSTALLING the REAR springs which is extremely difficult because you can't get enough leverage with your arm extended. Observing my frustration, my wife recommended taking off the back side. You can't simply take off the back,... Read more

• Won't start
• Will not agitate
• Will not drain

Replace the broken switch Read more

Replaced the coupler gasket. No leaks now. Read more

1. Sleeve for input, Injector valve, nozzle and seal for input fixed this problem. Probably the main part that was the trouble was a deformed Injector Valve which is a rubber tube with an internal retention groove at the wide part that grips the Nozzle. The Sleeve and the Nozzle are hard plastic parts that basically looked fine, but I replaced them anyway while I was in there. Additionally I replaced the rubber Seal for Input which seals the plastic input fitting to the tub just to make sure... Read more

We watched the video before we purchased the parts for this project. We wanted to make sure exactly what parts we would need. Thanks for having this information available. We purchased the mounting stem repair kit,,tub bearing kit, 3 new bolt/washers that hold the outer tub in place and the spanner wrench. Cleaned everything... NOTE :TAKE THE TIME TO CLEAN YOUR FILTERS ON THE BOTTOM. Thing went back together smoothly. We refereed back to the video when in doubt. Total repair $118.00... Read more