Julien Parts

The Door Cable Assembly is an OEM part for Whirlpool dishwashers. It plays a crucial role in connecting the dishwasher door to the door springs, ensuring smooth and balanced opening and closing. This assembly helps in controlling the door's tension and preventing it from falling open or slamming shut.

Causes of a bad door cable assembly can include wear and tear from frequent use, fraying or breaking of the cable, or damage due to accidental mishandling. Over time, the cable can become less effective, leading to issues with the door's functionality.

Symptoms of a bad door cable assembly include:

• The door falling open unexpectedly
• Difficulty in opening or closing the door
• The door not staying securely in place
• Noticeable slack or damage to the cable

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Pump Filter is an OEM part for Whirlpool dishwashers. This part is strategically designed to trap and filter out food particles, debris, and other substances that could clog the dishwasher's pump and drainage system.

A bad Pump Filter can result from debris buildup, wear and tear, and structural damage. This can hinder water flow, reduce cleaning efficiency, and compromise particle trapping ability.

Symptoms of a malfunctioning Pump Filter include:

• Poor cleaning results, as clogged filters can impede water flow and reduce the dishwasher's effectiveness.
• Water not draining properly, potentially leading to water pooling at the bottom of the dishwasher.
• Unusual noises from the dishwasher, which can indicate that the pump is working harder than normal to circulate water through a clogged filter.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This dishwasher wash impeller mounts on the circulation pump to drive water through the spray arms. A worn or damaged impeller can cause weak spray, poor cleaning, or noise; replacing it restores proper wash pressure. What it does:

• Moves water from the circulation pump through the filter and spray arms for effective cleaning
• Maintains proper wash pressure and spray action during the cycle
• Common fix for poor cleaning, spray arms not turning, or weak/no water circulation
• May reduce grinding or rumbling noises caused by broken or stripped impeller blades

• Includes 1 wash impeller

• Disconnect electrical power and shut off the water supply before servicing
• Remove the lower rack and spray arm; take off filters/sump cover to access the impeller
• Note impeller orientation; transfer any spacers as found and secure the impeller without overtightening
• Reassemble, check for leaks, and verify spray arm rotation after a test cycle

This water inlet valve regulates the flow of household water into the appliance. When the control energizes the solenoid, it opens to deliver the correct amount of water for filling and operation, restoring proper flow and performance.

• Controls on/off flow from the household water supply
• Opens when signaled to provide the correct amount of water for fill functions
• Helps maintain consistent water flow to the system
• Common failure symptoms: no water flow, slow fill, intermittent filling, or leaking at the valve body

• Disconnect power and turn off the water supply before servicing
• Place a towel to catch residual water and relieve line pressure
• Note tubing and wire locations before removal; transfer any brackets or clips as needed
• After installation, restore water and power, check for leaks, and purge air from the lines

This heater warms the wash water inside the tub during selected cycles. Replacing a failed element restores proper water temperatures, supporting cleaning performance and preventing extended run times or incomplete cycles. What it does:

• Heats water in the washer tub during hot/sanitize/temperature-controlled cycles
• Helps maintain target temperature for effective cleaning and stain removal
• Common symptoms include water not heating, cycles taking unusually long, or cycles stopping early
• Accompany control errors related to water temperature or the heater circuit

• 1 heater

• Disconnect power and shut off water supplies before servicing
• Access is typically from the rear or bottom; be prepared for residual water when removing the old element
• Clean sealing surfaces and seat the element fully; tighten fasteners evenly to prevent leaks
• After installation, run a hot cycle to check for leaks and heating

Color: gray. Measures about 3-3/4 inches wide by a 1/2 inch high.

Restore safe, smooth door operation with this dishwasher door spring. It counterbalances the door's weight so it opens and closes in a controlled way, preventing a sudden drop when the original spring breaks or fatigues.

• Provides the tension that counterbalances the dishwasher door through the hinge mechanism
• Helps prevent the door from slamming open or feeling unusually heavy
• Restores smooth, even door movement side-to-side
• Typical symptoms: door drops quickly, feels heavier than normal, uneven motion, or a visibly broken/stretched spring

• Disconnect power and shut off water before servicing
• Remove the toe/kick panel to access the hinge area
• Support the door, then move it slightly to relieve tension before unhooking the old spring
• Attach the new spring between the frame anchor and hinge arm; if your model uses two springs, replace both sides for even tension

This dishwasher door seal fits into the tub channel to create a tight, water-resistant barrier when the door closes. Replacing a worn gasket helps stop nuisance leaks and restores proper door compression and moisture containment.

• Creates the primary seal around the dishwasher tub opening when the door is closed
• Helps keep wash water, suds, and steam inside the wash cavity
• Wear can lead to drips at the front corners or along the sides
• Replace if the gasket is cracked, torn, flattened, or no longer sealing; the door may be harder to latch

• Disconnect power and turn off the water supply before servicing
• Remove the old gasket and thoroughly clean the channel of debris and residue
• Warm and relax the new gasket; start at the top center and press evenly into the channel without stretching
• Close the door for several hours to help the seal set; run a test cycle and check for leaks

Dishwasher silverware basket includes both halves. Color: gray. Measures about 8 inches wide by 9-1/2 inches high by 12 inches deep.

This electronic control board kit is the appliance's central controller, coordinating inputs and powering key components. Replacing a failed board restores proper operation, responsive controls, and reliable cycle management. What it does:

• Manages timing and power to motors, valves, heaters, fans, and other loads
• Interprets sensor and user-interface signals to start, run, and end cycles correctly
• Common failure signs: dead or unresponsive controls, cycles that won't start/finish, repeated error codes, or intermittent operation
• Helps address issues caused by power surges or board damage

• 1 electronic control board (module)

• Disconnect electrical power to the appliance; turn off gas/water if applicable
• Use ESD protection and handle the board by its edges
• Photograph wiring; transfer connectors one at a time and match any jumpers/DIP-switch settings from the original board
• Restore power and perform any model-specific tests or programming per OEM instructions

Lower wash arm redirects pressurized water across the dishwasher's lower rack to rinse and remove food and residue, restoring intended wash coverage and improving cleaning performance. What it does:

• Directs jets of water through multiple spray holes to rinse dishes on the lower rack.
• Helps remove stuck-on food, film and spotting on plates, bowls and cookware.
• Replaces cracked, clogged or broken lower spray arms that can cause poor cleaning or leftover residue.
• Works with the dishwasher's pump flow to maintain proper spray pattern across the lower rack.

• Refer to your model's parts diagram and instructions; the arm commonly snaps or threads onto the lower spray arm mount and procedures vary by model.
• Always disconnect power to the dishwasher before servicing; follow basic safety precautions.
• Clean the filter and any debris from spray holes before installing to avoid re-clogging.
• Inspect the mounting clip or retaining nut when removing the old arm and replace if damaged.

This dishwasher drain hose channels wastewater from the pump to your home drain or air gap. Replacing a cracked, kinked, or clogged hose restores proper draining performance and helps prevent leaks or water backing into the tub. What it does:

• Routes wastewater from the dishwasher to the household drain or air gap
• A damaged, kinked, or blocked hose can cause slow/no drain, standing water, or leaks
• Visible splits, soft spots, or persistent odors/backflow are common signs the hose should be replaced
• Restores reliable draining and helps protect surrounding cabinets and flooring from water damage

• 1 drain hose

• Disconnect power and shut off water before servicing
• Pull the dishwasher forward and place a towel or pan to catch residual water
• Match the original routing and maintain a proper high loop or air gap per local code to prevent backflow
• Secure connections with clamps, ensure the hose isn't kinked, and run a test cycle to check for leaks

Screw: 8-16 x 3/8 inch.

The fold-away tine latch secures the flip-down tines on your dishwasher rack. It locks tines upright to support dishes and releases to fold them flat, restoring rack flexibility and preventing tines from collapsing during cycles.

• Locks fold-away tines in the up position to support dishes and glassware
• Releases to allow tines to fold flat for larger items
• Helps maintain stable, organized loading during wash cycles
• Common symptoms: tines won't stay upright, latch won't click/hold, missing or broken latch

• Open the dishwasher door and remove the affected rack for access
• Note the latch orientation; release the old latch from the tine assembly
• Snap the new latch into place until it engages
• A small flat-blade screwdriver can help release locking tabs

This roller fits the cable bracket assembly and helps guide the cable smoothly to reduce binding and wear. It restores proper cable tracking so the mechanism moves more quietly and reliably. What it does:

• Guides and supports the cable within the bracket so the cable runs true
• Reduces rubbing, binding, and premature cable wear
• Helps eliminate squeaks or grinding where the cable contacts the bracket
• Restores smoother operation of the affected door/assembly movement

• One roller for the cable bracket (quantity: 1)

• Disconnect power before starting any repair and follow all safety guidelines
• Requires basic hand tools; access the bracket per your model's service instructions
• Inspect the cable and bracket for wear or damage and replace if necessary
• Test operation after installation to ensure proper cable routing and smooth movement