Kelvinator Parts

• Will not fill with water

Replacing the inlet valve solved the problem. The old valve was somehow clogged with white sediment. I probably could have taken it off and cleaned it out if I'd known, but replacing the valve was much easier. Took about half an hour to repair. Video walk through was extremely helpful. Great to have a working dishwasher again! Read more

Checked compressor windings - ok. Start relay looked no rattle or burning. Start capacitor seamed ok but hard to check. No 120VC to start relay at any time. Ordered thermistor, and electronic control unit. Figuring it was a bad thermistor not telling the ECU it was warm and to turn on the compressor. Or the ECU was damaged and was not sending the 120v to the compressor. Changed the thermistor first (cheapest part and as Appliance parts pros has a return policy I wanted to start there). ... Read more

• Will not dispense detergent

I bought a replacement part and changed it out. Read more

The repair was a success. The switch and came looked different from the original. I called Appliance Parts Pro, they lady on the phone said that Frigidaire changed the switch and how to wire it up correctly. Problem solved. It all works as it should. Read more

• Not drying dishes properly

Turned off power to dishwasher. Removed front bottom cover of dishwasher and removed the wires going to each end of the heating element. unscrewed the two nuts holding the faulty heating element in place. Then removed bottmo dish rack and spinning washer arm from inside the dishwasher. Removed old heating element and replaced with new one. Installed in reverse order (tightened two nuts, connected wires, etc.). Turned power on as last step and was off and running...or should I say washing. Read more

I replaced the defrost thermostat and the fan motor. Very impressed with service. Ordered the parts Thursday night and they where on my porch Saturday morning. Read more

Gasket and liner arrived as planned. Clips were a day later. Used "hog ring" pliers to remove the clips, worked great. Pre-punched holes in the gasket did not match the original but the plastic liner did. Used an ice pick to punch the gasket and inserted the clips. This is a chest freezer, so install the hinge side first. Read more

Loosened the top half screws, pulled the old seal out, put new seal in, snugged top screws, repeated process for the bottom. Went well, no problems. Read more

Called for a repair tech, he told me what the problem was, I had already checked out the burnt connections,repair was going to be $450-500 range, My wife & I discussed repair or new range,repair won out.I am a retired machine repairman with some elect skills,so looked up parts online ordered them, installed the new control board with the new "decal" , checked out the oven, etc, everything seems good to go. This range is only 6.5 yrs old , they don't seem to make them last as long as the ones I... Read more

No problem, 1 min to fix Read more

The clips on the rear side of the drawer box were broken. Easy to locate the part on the website. Part in hand in two days and installed in about five minutes. Needed to remove the drawer and use a 1/4" driver, remove the broken slide and install the new one. Read more

Replaced hose Read more

Easy job, I screwed the parts to the dishwasher Read more

My barely three year old Frigidaire upright freezer quit running and we discovered it when most of the contents were just starting to thaw. Luckily we have nearby neighbors that my wife walks with most days and two or three of them came to our rescue with available freezer space to save the more valuable things like meat and seafood. The compressor would not come on, no fan, no noises of any kind but the light came on when the door was opened so obviously it had power. I unplugged it for a... Read more

Installation of the new handle after receiving a very timely shipment from appliance parts pros was simple. I lined up the top of the handle (hooked 90 degrees over the door) and then swung the handle down to meet the corresponding lower screw. The bottom slid and locked into place, then I screwed the top bolt in. Voila! Read more