Kenmore / Sears Cooktop Parts

Removed and replaced 3 door switches and mounting bar that holds switches plastic gets brittle with age and each switch comes out slightly different from each other, the chances of breaking a mounting pin is very easy. care should be taken when snapping mounting bar back into place to insure top latch and bottom latch locate properly insure bar is proper aligned when tightening screws their is free play in mounting bracket that could affect door properly engaging switches. NOTE that their are... Read more

Order the part to ApliancePartsPro and within 3 days I had it delivered to my front door. Looked up in their help page and was guided how to do it. It was so ease . I will recomend all my friend to get their parts at ApliancePartsPro. I am very please with the service and quality. Read more

Stove is a GE Adora Model JBP63HH2bb. It took me forever to figure out how the burner was attached to the rails. My glass top was different than any instructions found on the internet for changing out a burner. The burners on this one are held to the bottom of the glass cook top by two rails that cross the bottom of the burner assemblies. In order to get too the burners you must remove 4 Phillips screws to lower the rails and burners from the cooktop. I suggest two people do this because... Read more

• Won't start
• Element will not heat

I ordered the recommended Infinite Heat Switch Kit and Element Receptacle and Wire Kit and installed them. The latter was a breeze, appearing to be exactly the same as the original, except for the wire color. The switch, though, was another story. It is a RobertShaw "replacement" part, designed, it seems, for use in the greatest number of original units as possible. The most obvious difference between this switch and the original (besides its comparatively small size) is the long, segmented... Read more

Ordered replacement drip pans Read more

• Little to no heat when baking

Turned off the power to the oven, removed the old element and installed a new element that I purchased from Appliance Pros.com. The part was delivered in a timely manner and was packed securely for shipping. Thanks!!!!!! Read more

Ordered correct replacement parts (your online form helped to identify correct valves 2 had black dot on inside stem for back small burner 1 had red dot for larger front burner). locked stove, turned off gas, unplugged cord. removed knobs, 5 screws and front plate also removed L shaped plate below knobs for better access to comp. fittings. pulled off ignitior controls loosened compression fittings (hard to get wrench on nut but doable), removed screw holding valve to manifold. reversed order... Read more

Cleaned/ soaked all burners in Ammonia and scraped off the remaining with a pumice stone. Oiled all screws. Replaced (4) ignitors or electrodes and module kit/ right front burner/ burner switch harness. Although this was the third order of switches from 3 different places including the local supplier due to the switches being manufactured upside down and lit on low on the first attempt. (Since I was going to have to open it up again to either repair or remove and return the upside-down harness... Read more

• Element will not heat

Replaced the Infinite Switch and that solved the problem. Did not need to replace the Surface Element Read more

• Element will not heat

Watched the video when the part came, and 5 minutes later, our 25 year old stove is once again working like a champ. Read more

• Door won't close
• Oven not heating evenly

First of all Appliance Parts Pros is the best!! I would not have had the confidence to make this repair myself without their outstanding videos and Q&A sections on their website. And their prices for parts are very competitive. Like many stories on the website, my oven would heat up beyond the temperature set point. When it reached the target temperature, the lower heating element (I think this is the “bake” element) would shutoff, but the top element (“broil” element I believe) would remain on... Read more

Replaced the gas regulator and the oven igniter. It was not a very difficult repair.. most of the parts were easy to get to. The biggest challenge was disconnecting the gas hose from the regulator. It had "pipe dope" (sealant) on the threads. I reconnected with yellow gas pipe tape. Read more

• Element will not heat
• Little to no heat when broiling
• Oven not heating evenly

With my tools Read more

Online chat here said that the oven sensor should be replaced. I got the feeling that was a bit off, so I went with my gut and ordered the thermostat as well. Replaced the sensor and that didn't fix it. Replaced the thermostat and it worked like a charm! Disappointed that they were overconfident in their answer and it would have taken me more days to fix - but, the products came in quickly (basically, next day) and were correct. Online video for my particular oven was incorrect - but it's... Read more

• Won't start

Took off old, replaced with new. Cross reference worked well, all GE parts. Saved a lot of money compared to local supplier. Read more

First off thanks AppliancePartsPro.com... Another project in the books... I ordered a new switch harness and spark module because I just decided the why not do them both. They arrived very promptly, uses very simple tools most people have I would think. After unplugging it and shutting off the propane. I removed valve knobs. Then the burners with a nut driver and two sizes of sockets. The stove top and valve cover six Philips head screws. Gained complete access to the stove top. Removed... Read more