Kenmore / Sears Dishwasher Parts

The Tine Clip Kit is an OEM part for Bosch dishwashers. This kit includes clips that secure the tines in the dishwasher rack, ensuring that dishes stay in place during the washing cycle for optimal cleaning performance.

Causes of a bad tine clip can include wear and tear from regular use, exposure to high temperatures and detergents, or accidental damage. Faulty or broken tine clips can result in unstable tines, making it difficult to properly load and organize dishes in the dishwasher.

Symptoms of a bad Tine Clip include:

• Tines not standing upright or falling over
• Difficulty in loading or arranging dishes
• Rattling noises during the wash cycle
• Loose or missing clips

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

The Detergent Cup Latch W Spring is an OEM part for Bosch dishwashers. This latch securely closes the detergent dispenser cup, containing detergent during the wash cycle.

Causes of a bad latch can include wear and fatigue of the latching spring over many uses.

Symptoms of a bad detergent cup latch include:

• The cup popping open unexpectedly during a wash
• Difficulty fully closing and hearing the "click" of the latch
• Detergent leakage resulting in reduced cleaning

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This MultiFence is a multi-position rack fence that mounts to the rack to support and organize dishes, lids, and bakeware. It helps keep items upright and in place so cycles run smoothly and cleaning performance stays consistent. What it does:

• Attaches to the rack and flips/locks to secure items of different sizes
• Helps prevent plates, lids, and trays from tipping or sliding during operation
• Replaces a fence that is cracked, warped, missing, or won't stay in position
• Common symptoms include dishes falling over, rattling during cycles, or poor results from shifted loads

• One MultiFence rack fence

• Disconnect power to the appliance; turn off water supply if servicing a dishwasher
• Pull the rack out; release the retaining tabs or clips to remove the old fence
• Align and snap the new fence onto the rack wires; ensure it pivots and locks properly
• Reinstall the rack and verify smooth operation

The Nozzle Assembly is an OEM part for LG dishwashers, designed to enhance the efficiency and effectiveness of the water spray during the wash cycle. This component directs water to the dishes to ensure thorough cleaning and rinsing. Positioned strategically within the dishwasher, the nozzle assembly plays a role in distributing water evenly across all dishes, regardless of their placement in the rack.

The causes for these issues can range from clogs within the nozzle from food particles or mineral deposits from hard water, to physical damage that can occur through wear and tear or during loading and unloading of dishes.  

Symptoms of a failing Nozzle Assembly include:

• Dishes not being cleaned properly, with food particles or soap residue remaining after cycles
• Water not reaching all areas of the dishwasher, leading to uneven cleaning
• Decreased water pressure, which can affect the dishwasher's ability to remove tough food stains

This OEM LG part is also compatible with some Kenmore models.

The Micro Filter Basket Assembly is an OEM part for Bosch dishwashers. This component is essential for trapping food particles and debris during the wash cycle, preventing them from re-entering the clean water circulation. By effectively filtering out residues, the micro filter ensures that your dishes emerge spotless and free from food remnants. 

Causes of a bad micro filter basket assembly include clogging from accumulated food particles, wear and tear from regular use, and damage such as cracks or warping that can compromise its filtering capability.

Symptoms of a bad micro filter basket assembly include:

• Dishes not getting thoroughly cleaned
• Visible debris remaining on dishes after washing
• Unusual noises from the dishwasher indicating struggling pumps or motors

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

The Door Balance Spring is an OEM part for Whirlpool dishwashers. This part provides tension and balance to the dishwasher door, ensuring it opens and closes smoothly and stays in the desired position when loading or unloading dishes.  

Causes of damage to the door balance spring can include normal wear and tear from frequent use, corrosion due to moisture and detergent exposure, or mechanical failure from excessive force being applied to the door.  

Symptoms of a bad Door Balance Spring include:

• The dishwasher door falling open too quickly or with too much force 
• Difficulty in keeping the door open or having it snap shut unexpectedly 
• A noticeable difference in the effort required to open or close the dishwasher door 

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Hinge Spring is an OEM part for LG dishwashers. This spring works with the door hinge to provide the necessary tension for smooth opening and closing of the dishwasher door, ensuring it stays securely in place when opened or closed.

Over time, the hinge spring can become worn out or break due to regular use, metal fatigue, or accidental impacts. Causes of a bad hinge spring include excessive wear, rust or corrosion, and physical damage from forceful door operation.

Symptoms of a bad hinge spring include:

• The dishwasher door dropping suddenly or not staying in the open position
• Difficulty in opening or closing the door smoothly
• Unusual noises, such as squeaking or popping, when operating the door
• The door feeling loose or unbalanced

This OEM LG part is also compatible with Sears/Kenmore models.

The Thermal Fuse is an OEM part for Whirlpool dishwashers. It serves as a crucial safety component that prevents the appliance from overheating by cutting off electrical power if the temperature inside the dishwasher becomes too high. This helps protect both the dishwasher and your home from potential fire hazards.

Causes of a bad thermal fuse can include overheating due to blocked air vents, malfunctioning components that lead to excessive heat, or electrical surges that damage the fuse. Over time, regular wear and tear can also contribute to the fuse's failure.

Symptoms of a bad thermal fuse include:

• The dishwasher not starting or running
• The control panel not responding
• The dishwasher stopping unexpectedly mid-cycle
• No indicator lights or sounds when attempting to operate the dishwasher

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Toe Panel Insulation is an OEM part for Whirlpool dishwashers. This part was designed to enhance the appliance's performance by reducing noise and preventing heat escape from the bottom of the dishwasher. This insulation panel fits snugly behind the dishwasher's toe panel, which is located at the lower front part of the unit. 

Causes of a bad Toe Panel Insulation might include wear and tear over time, damage during appliance installation or removal, or deterioration due to moisture exposure. 

Symptoms of inadequate or damaged Toe Panel Insulation include:

• Noticeable increase in noise level from the dishwasher, making it more disruptive during its operation.
• Excess heat felt near the base of the dishwasher, indicating heat loss.
• Potential for condensation or slight temperature changes in the kitchen due to the heat emitted from the dishwasher.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Pump is an OEM component for Whirlpool dishwashers. It refers to the water pump component that circulates water throughout the dishwasher during cycles. 

A cause of a faulty pump can include normal wear over many uses. The continuous motor operation puts strain on internal seals and impellers. Mineral deposits from hard water can also clog pump parts over time.

Symptoms of a bad pump include: 

• No water filling or draining during cycles
• Odd noises or grinding sounds coming from inside 
• Leaks or water pooling in the bottom of the dishwasher
• Lights or controls failing to function properly

This pump is also compatible in some KitchenAid, Jenn-Air, Amana, and Kenmore models.

The Drain Hose is an OEM part for Bosch dishwashers. This hose is responsible for carrying the wastewater out of the dishwasher and into the household plumbing system during the draining cycle. It ensures the efficient removal of dirty water, allowing the dishwasher to function correctly and maintain optimal cleaning performance.

Causes of a bad drain hose can include blockages from food particles or debris, kinks or twists in the hose, or damage from wear and tear over time. If the drain hose is compromised, it can lead to drainage problems and potential water leaks.

Symptoms of a bad drain hose include:

• Water not draining from the dishwasher
• Puddles of water around or under the dishwasher
• Error codes related to drainage issues
• Visible damage or cracks in the hose

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

The Spray Arm Nut is an OEM replacement part for Whirlpool dishwashers. This nut secures the spray arm to the dishwasher, ensuring it stays in place while distributing water to clean dishes effectively.

The spray arm nut can become worn out or damaged due to regular use, exposure to high water pressure, or accumulation of debris. Over time, it may loosen or crack, affecting the spray arm's performance.

Symptoms of a bad spray arm nut include:

• The spray arm not rotating properly
• Water not being distributed evenly during the wash cycle
• The spray arm detaching from its mount
• Noisy operation or rattling sounds

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Rack Adjuster is an OEM part for Whirlpool dishwashers, designed to allow for the easy adjustment of the dishwasher rack's height. This feature accommodates dishes of various sizes. By providing the flexibility to adjust the rack height, this part enhances the dishwasher's adaptability to different washing needs.

Symptoms of a failing Rack Adjuster include:

• Difficulty in adjusting the dishwasher rack's height
• The rack becoming loose or detaching from the adjuster
• Visible wear or damage to the adjuster components

Causes of a bad Rack Adjuster can range from normal wear and tear, which gradually degrades its components, to accidental damage during loading or unloading of dishes. 

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

The Water Inlet Valve is an OEM part for GE dishwashers. It is responsible for opening and closing the water supply to the dishwasher. It regulates the water pressure and ensures the proper amount of water is dispensed for each cycle. This part has a 3/8” inlet and includes the mounting bracket.

Causes of a faulty water inlet valve can include wear and tear over time, sediment or debris buildup, electrical component failure, or damage due to high water pressure. These factors can result in issues such as inadequate water flow, leaks, or the dishwasher not filling or draining properly.

Symptoms of a bad water inlet valve may include:

• Insufficient water supply or low water pressure
• Leaks around the valve area
• Inability to start or complete dishwasher cycles

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 

The Heating Element Nut is an OEM part for Frigidaire dishwashers. It plays a crucial role in securing the heating element in place, ensuring it functions effectively to heat water during the wash cycle. This component ensures the stability and proper operation of the dishwasher's heating element, contributing to the machine's overall efficiency and performance.

Causes of a bad part can include physical damage during maintenance or installation, corrosion over time due to exposure to water and detergents, or general wear and tear that affects its ability to securely hold the heating element in place.

Symptoms of a bad Heating Element Nut include:

• Loose heating element, leading to inefficient heating or water not heating at all
• Water leakage from the heating element area, potentially caused by a poor seal
• Unusual noises during the dishwasher cycle

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

The Wheel is an OEM part for Whirlpool dishwashers. This component is typically found on the lower or upper rack and allows the rack to slide in and out smoothly for easy loading and unloading of dishes. 

You should replace the wheel if it becomes worn, cracked, or broken. Causes of a bad wheel can include regular wear and tear from frequent use, damage from heavy loads or sharp objects, and material fatigue over time. A damaged wheel can hinder the movement of the racks and affect the loading and unloading process.

Symptoms of a bad wheel include:

• Difficulty sliding the dishwasher rack in and out
• The rack getting stuck or not aligning properly on the tracks
• Visible cracks, breaks, or wear on the wheel
• Unusual noises when moving the rack

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.