Kenmore / Sears Dishwasher Spray Arm & Related

Also Order Spray Arm Seal

This is the upper spray arm that distributes wash water to the top rack. Replacing a cracked, warped, or clogged arm restores even spray coverage and helps the arm spin freely so glasses and bowls come out consistently clean.

• Directs high-pressure jets to the upper rack and rotates under water pressure for full coverage
• Maintains even water distribution to improve cleaning performance
• Common symptoms of a failed arm: top-rack items not getting clean, arm not spinning, uneven spray, cracks or clogged nozzles

• Disconnect power and water supply before servicing the dishwasher
• Remove or lower the upper rack if needed; release the retaining nut/clip and pull the old arm straight off
• Seat the new arm fully on the hub/manifold and secure the retainer; verify it spins freely
• Run a short test cycle to ensure proper spray and operation

This tower protector is a small plastic cover that fits over the dishwasher's spray tower. It helps keep dishes and utensils from obstructing the tower's spray outlets so water can circulate properly for consistent cleaning.

• Shields the spray tower to prevent items from blocking water flow
• Helps maintain proper spray pressure and coverage to upper areas
• Replaces cracked, melted, or missing protectors that can lead to poor cleaning
• Common signs it's needed: protector is broken/loose, deformed, or repeatedly falls off; dishes aren't getting clean due to blocked spray

• Disconnect power and water before service
• Allow the dishwasher interior to cool
• Open the door, remove the lower rack, and snap the protector into place per the tower/rack design
• Verify it seats securely and does not interfere with the spray tower movement

This is the dishwasher upper spray arm that delivers water across the top rack for effective cleaning. It replaces a worn or damaged spray arm to restore proper water distribution and rinse performance. What it does:

• Spins and sprays water across the top rack to help remove food and detergent residue
• Restores proper spray pattern when the original arm is cracked, clogged, or not turning
• Helps prevent poor cleaning, spots, or missed areas on top-rack dishes
• Works with the dishwasher's water delivery system to maintain rinse and wash coverage

• One upper spray arm

• Turn off power and water to the dishwasher before beginning any service
• Inspect and clear any debris from the spray arm and the mounting area before installation
• Hand-tighten or snap the arm into place per your model's instructions; avoid overtightening

This manifold is the OEM gas valve assembly that routes propane or natural gas from the regulator to the oven and burner valves so the appliance can ignite and heat properly. Designed as a direct-replacement service part. What it does

• Channels gas from the regulator to individual burner/oven valves so each burner can ignite.
• Replaces a worn or damaged manifold that can cause weak or no ignition.
• Addresses symptoms such as burners that won't light, oven failing to heat, or inconsistent flame across burners.
• Works with the appliance's existing regulator and control valves when installed correctly.

• Turn off gas supply and electrical power before attempting removal or service.
• Inspect fittings and gaskets; replace any damaged seals to prevent leaks.
• After installation, perform a gas-leak test and verify proper ignition and flame patterns.

This is a replacement hex nut used to secure appliance components and fasteners. It restores proper fastening where a stripped, missing, or damaged nut causes loose or rattling parts. What it does

• Secures mating bolts or threaded studs to hold panels, brackets, or assemblies in place
• Stops vibration-related loosening that can cause rattling or misalignment
• Replaces corroded, stripped, or missing nuts to restore a safe connection
• Works wherever the OEM specifies this nut for fastening duties

• One replacement hex nut

• Disconnect power (and water, if applicable) to the appliance before servicing
• Use the correct size wrench or socket to avoid rounding the nut
• Tighten snugly but avoid overtightening; replace if threads are damaged

Includes both left and right arms.

The Upper Spray Arm is an OEM part for Whirlpool dishwashers. It is located below the upper rack and functions to spray water onto dishes during the wash cycle for thorough cleaning.

Causes of a bad upper spray arm include clogs or mineral buildup that reduce or block water pressure, or physical damage rendering the arm unable to spin properly.

Symptoms of a bad upper spray arm include:

• Dirty or inadequately cleaned upper rack dishes
• Spinning noises or clunking from the wash arm area
• Uneven cleaning results

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Center Wash Arm Assembly is an OEM part compatible with Whirlpool dishwashers. It is a multi-spraying component located in the center of the lower dish rack that helps deliver water for superior washing performance. The arm rotates during the cycle to wash all accessible surfaces of dishes.

Symptoms of a bad Center Wash Arm Assembly include:

• Incomplete or inadequate cleaning of dishes, especially those in the lower rack  
• Mineral or hard water deposits building up on dishes
• Reduced water pressure or spray pattern from the wash arm nozzle(s)

Causes of a bad center wash arm can be mineral deposits clogging the nozzle openings over time, or physical damage such as bending or breaking of the arm assembly or its mounting bracket.

This OEM replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dishwashers.

The spray arm assembly distributes pressurized wash water through its jets and rotates to clean dishes. If it's cracked, clogged, or not turning freely, replacing it restores proper spray coverage and cleaning performance.

• Directs water through jet openings to wash dishes throughout the tub
• Rotates by water force for even spray coverage
• Common symptoms: poor cleaning results, arm not spinning, visible cracks/warping, or clogged holes
• May cause unusual knocking if the arm is loose or contacting items

• Disconnect power and turn off the water supply before servicing
• Remove the lower rack; release the existing spray arm from the center retainer (method varies by model)
• Clear any debris from the pump outlet and seating surface
• Seat the new arm fully and ensure it spins freely before running a test cycle

Notes: Only one screw hole is used now.

This arm mounts below upper dishrack.