Kenmore / Sears Gas Conv Kit Parts

This replacement tube restores a damaged or missing refrigerator tubing connection so the appliance can route fluids where intended and operate reliably. It's a direct-fit service part for the matching OEM assembly. What it does

• Provides a sealed conduit for fluid flow inside the refrigerator
• Re-establishes a proper connection when the original tube is cracked or broken
• Helps stop leaks or pooling caused by a damaged line
• Supports normal operation of the associated water/defrost subsystem

• One replacement tube as shown

• Only install when the appliance is powered off and disconnected from its water supply if applicable
• Inspect adjoining fittings and replace any worn clamps or seals to ensure a leak-free connection
• Use appropriate tools; avoid sharp bends that can kink or restrict the tube

A single gas burner orifice that meters fuel flow to a range or oven burner for consistent flame sizing and reliable cooking performance. Replaces a worn or clogged orifice to help restore steady ignition and even heat. What it does:

• Controls the amount of gas delivered to a burner for proper flame height and heat output
• Helps maintain consistent cooking and baking temperatures when functioning correctly
• A clogged or damaged orifice can cause weak or uneven flames, slow ignition, or poor heating
• Works as a small, precision-fit insert that sits in the burner assembly

• Turn off the appliance and shut off the gas supply before servicing
• Use a wrench or socket sized to the orifice and avoid rounding the fitting
• Inspect burner ports and clean any debris before installing the new orifice

This oven pilot assembly supplies the small, continuous flame used to ignite the main gas burner in a gas oven. It restores reliable ignition so the broil/bake burners can light when the oven calls for heat. What it does:

• Provides the standing pilot flame that ignites the oven's main burner
• Allows safe ignition when the oven control sends gas to the burner
• Common repair for ovens that fail to light or have intermittent ignition
• Can reduce repeated clicking or delayed lighting when replaced

• One oven pilot assembly

• Turn off gas supply and disconnect electrical power before starting any work
• Verify proper alignment and secure mounting of the pilot tip to the burner hood
• After installation, check for gas leaks with a leak-detection solution and confirm proper ignition

Location: Left rear.

This tube and orifice assembly delivers regulated gas from the supply line to a range/oven burner so the appliance lights and maintains a steady flame. It restores correct fuel flow for safe, consistent heating. What it does:

• Directs gas from the manifold to the burner through a precisely sized orifice for proper flame shape and heat
• Helps fix weak or uneven flames, burners that won't ignite, or burners that barely stay lit
• Used when the existing tube is damaged, bent, clogged, or the orifice is worn or incorrect
• Works with the appliance's factory gas system to maintain proper combustion when correctly installed

• One tube and orifice assembly

• Turn off gas supply and power to the appliance before starting work
• Use proper tools and fittings; verify correct orientation and seating of the orifice and tube
• After installation, perform a leak test and observe burner ignition and flame pattern

This LP conversion kit lets a compatible gas range be converted from natural gas to liquid propane so it runs safely on LP fuel. It provides the small parts needed to change burner flow and restore proper combustion. What it does:

• Replaces factory orifices and/or regulator components so burners meter propane correctly
• Helps correct symptoms like yellow flames, sputtering burners, or poor heat when using LP
• Enables safe operation after fuel-type change when used with correct model conversion steps
• Preserves burner performance and efficiency once installed per manufacturer instructions

• LP conversion kit components

• Installation must follow the appliance manufacturer's conversion instructions exactly
• Use appropriate tools and discrete part identification; do not alter parts beyond instructions
• Turn off gas supply and disconnect power before starting; check for leaks after conversion

This ignitor orifice assembly is the gas burner component that routes fuel to the oven ignitor so the bake/ broil burners light reliably. Replaces a worn or damaged orifice assembly to restore normal ignition and consistent burner flame. What it does

• Directs gas to the ignitor and burner for safe ignition of the oven burner
• Helps maintain a steady flame for even cooking when operating correctly
• Common symptom: oven fails to light or takes multiple tries to ignite
• Common symptom: weak or uneven flame around the burner head

• One ignitor orifice assembly as shown

• Disconnect power and shut off the gas supply before any service
• Designed to mount at the oven burner; handle components and tubing carefully to avoid damage
• Use appropriate fittings and check for gas leaks before restoring use

This orifice spud directs gas flow to a burner for correct flame performance, restoring safe, consistent ignition and heat. It's a direct-replacement component used where the factory orifice has become damaged or worn. What it does:

• Controls the gas flow to a specific burner for proper flame size and combustion
• Helps restore consistent ignition and even heating when a burner burns low or unevenly
• Can stop symptoms like weak or unstable flames and uneven cooking
• Does not alter appliance settings—matches OEM flow characteristics when installed

• Turn off the gas supply and power to the appliance before starting any work
• Use appropriate tools and thread sealant rated for gas joints if required by the manufacturer
• After installation, check all connections for leaks with a soap solution or approved leak detector
• Gas-system repairs are safety-sensitive; perform the replacement

Natural gas. LG 1.68mm

LP orifice / size #84 (5k)

Orifice spud secures the burner orifice to the gas valve/manifold and directs fuel to the burner for proper flame performance. Replaces a damaged or corroded spud to help restore correct gas flow at the burner. What it does:

• Holds the burner orifice in place and channels gas from the valve to the burner.
• Helps maintain consistent flame size for even heating and cooking.
• Commonly used when a burner has weak, uneven, or intermittent flame performance.
• Replace if the spud is cracked, corroded, damaged, or leaking.

• Turn off the appliance's gas supply and disconnect power before beginning any repairs.
• Remove burner components per the service manual and install the spud in the same orientation as the original.
• Hand-start threads, then snug with the appropriate wrench—do not overtighten.
• After installation, check fittings for leaks with an approved leak-detection method; if you smell gas or suspect a leak, stop.

This replacement nozzle assembly directs and controls water flow in the appliance, restoring proper delivery to the dispenser or ice-making components. It replaces a worn or damaged nozzle to help stop leaks and restore consistent flow. What it does

• Directs water from the supply line to the dispenser or ice-making fill tube.
• Helps stop spraying or leaking when the original nozzle is cracked or blocked.
• Restores steady water flow when the dispenser produces weak or intermittent water.
• Fits into the original mounting and seals the water path when properly installed.

• One nozzle assembly as shown.

• Turn off water supply and unplug the appliance before starting work.
• Inspect surrounding seals and tubing; replace any damaged parts to ensure a proper seal.
• Hand-tighten fittings and check for leaks after restoring power and water.

This ignitor orifice assembly routes and meters gas to the oven burner ignitor so the oven lights reliably and reaches cooking temperature. It's a direct-replacement part used when ignition is inconsistent or the burner won't light. What it does:

• Controls gas flow from the manifold to the oven burner ignitor for proper ignition
• Helps ignition occur quickly and consistently so the oven can reach set temperatures
• Common symptoms: oven won't light, delayed or intermittent ignition, or weak/uneven heating
• Works with the oven's ignition system; replaces worn or damaged orifice assemblies

• Turn off electrical power and shut off the gas supply before starting work
• Use proper tools; do not force fittings or over-tighten connections
• After installation, restore power/gas and test the oven for proper ignition and operation