Kenmore / Sears Range / Cooktop / Oven Heating Element

This dual surface element restores steady, selectable heat to a cooking zone on your electric range or cooktop. It provides two heating areas in one burner position so you can match heat output to small or larger cookware.

• Heats cookware by energizing the inner ring alone or both inner and outer rings together
• Helps resolve issues such as a surface burner not heating, only one ring heating, or intermittent/uneven heat
• Replaces a cracked, blistered, or visibly damaged element to restore reliable performance

• Disconnect power at the breaker and allow the cooktop to cool completely before servicing
• Access the element from beneath the cooktop; photograph wire locations for reference
• Carefully transfer any brackets, clips, or attached limiter from the original element if required
• Avoid touching the element surface; secure all connections and test both inner and dual settings after reassembly

This replacement bake element restores the lower oven heat in electric ranges/ovens. It brings back proper preheating and even baking performance when the original element is burned out or physically damaged. What it does:

• Provides the primary heat from the bottom of the oven during Bake cycles
• Common signs of failure: no heat in Bake, very long preheat times, uneven baking, or visible blisters/cracks on the element
• If Broil still works but Bake does not, the bake element is a likely failure point
• Located at the bottom of the oven cavity to deliver even, consistent heat

• 1 bake element

• Disconnect power at the breaker and let the oven cool completely before servicing
• Remove oven racks; take out the element's mounting screws and gently pull the element forward
• Transfer the two wires to the new element, keeping them from slipping back into the oven cavity
• Reinstall the element and screws, restore power, and test Bake

• With power disconnected, check the element for continuity; an open circuit typically indicates a failed element

This electric surface element replaces a failed top burner on your range or cooktop. Installing a new element restores dependable, even heat and responsive temperature control when a burner won't heat or behaves inconsistently.

• Provides the heat for the selected cooking zone when the surface control sends power
• Common signs of failure: burner does not heat, heats intermittently or unevenly, visible burn spots/cracks, or an open reading on a continuity test
• A shorted element may trip the breaker or spark when that burner is turned on

• Disconnect power at the breaker or unplug the appliance before servicing; allow the cooktop to cool completely
• Access the element per your model's service manual; support any glass surface to avoid stress cracks
• Note wire positions and transfer connections one at a time; reuse original mounts and hardware
• Ensure the element sits level and secure before reassembly and testing

This replacement heating element restores the heat your appliance needs to cook reliably. Swap in a fresh element to bring back consistent temperatures and dependable performance when the original has failed or become damaged.

• Converts electrical energy into heat for the appliance's cooking system
• Typical symptoms of a failed element: no heat, slow or uneven heating, visible blistering/cracks, or tripping the circuit breaker
• An open (no continuity) element will prevent the affected oven or surface zone from reaching set temperature
• Designed to fit specific models; match by model/part number for proper application

• Disconnect power at the breaker before servicing; elements run on high voltage
• Take a photo and move wires one at a time to the new element; ensure terminals are fully seated
• Handle the element carefully—do not bend, kink, or stress terminals
• Reuse existing mounting screws/brackets as applicable; verify no wires contact metal before restoring power

This is the radiant surface heating element that powers one burner on a glass-ceramic cooktop. Replacing a failed element restores fast, even heat and reliable temperature control for everyday cooking.

• Converts electrical energy into heat for a single cooktop zone
• Works with the burner control to cycle on/off and maintain temperature
• Common symptoms include no heat, intermittent heat, or very slow heating
• Visible hot spots, blisters, or cracks on the element indicate failure

• Disconnect power to the range/cooktop before servicing; high voltage is present
• Allow the glass top to cool; lift or remove it to access the element as your model requires
• Transfer wires one at a time to the new element; secure using existing brackets/mounts
• Ensure the element is centered under the glass and test operation before reassembly

This surface heating element restores reliable heat to an electric range or cooktop's top burner. Replace a failed or damaged element to bring back even, responsive heating for everyday cooking. What it does:

• Supplies heat to the selected surface burner when the control is turned on
• Can correct no-heat, weak or intermittent heat, or overheating due to internal failure
• Replaces elements with visible damage such as breaks, burn marks, or hot spots
• Helps restore consistent temperature control across the cooking zone

• 1 surface heating element

• Disconnect power at the breaker and allow the cooktop to cool completely before servicing
• Access the element per your model; note wire locations and any brackets before removal
• Transfer wires and any retaining hardware to the new element in the same positions
• Avoid stressing the element or insulation; ensure it sits level and clear of glass/trim before reassembly

The broil element is the oven's upper heating element. It delivers intense radiant heat for broiling; replacing a failed element restores proper broil performance and more even browning.

• Provides top, direct radiant heat during the Broil cycle
• Symptoms of failure: no broil heat, uneven broiling, visible blistering/cracks or breaks in the element, sparking or tripping the breaker when Broil is selected
• Helps restore proper searing/finishing from the top of the oven

• Disconnect power at the breaker or unplug the range before servicing
• Remove oven racks; support the element while removing its mounting screws
• Gently pull the element forward and disconnect the two wires; prevent wires from slipping behind the oven liner
• Make firm, clean terminal connections; avoid bending the element, reinstall screws, then test the Broil cycle

This is a radiant surface heating element for smooth-top electric ranges. It replaces a failed burner to restore up to 1300 watts of even heat and dependable temperature control under the glass-ceramic cooktop. What it does:

• Generates radiant heat beneath the glass surface when powered by the burner control
• Restores proper heating if a burner will not heat, heats unevenly, or cycles off too quickly
• Helps eliminate long heat-up times caused by a weakened or open element
• Replaces elements with visible damage such as broken ribbons, burn spots, or charred terminals

• 1 radiant surface element (1300W)

• Disconnect power at the breaker or unplug the range before servicing
• Allow the cooktop to cool fully; lift/prop the glass top to access the element
• Note wire positions; transfer any mounting brackets/clips from the old element and reconnect wires securely
• Handle the element carefully and avoid stressing the ribbon; reassemble and test the burner before finalizing

This bake element is the lower-oven heating source that brings your range or wall oven up to temperature for consistent baking. Replace a burned or damaged element to restore reliable preheat and even cooking results. What it does:

• Provides bottom heat during bake cycles for even, consistent cooking
• Primary heat source for preheating and maintaining set temperature
• Common symptoms: no heat in bake, slow preheat, won't reach temperature, uneven baking, visible blisters/breaks on the element
• Useful clue: broil works but bake does not

• 1 bake element

• Disconnect power at the breaker before servicing
• Remove racks; take out element mounting screws; pull element forward to access terminals
• Transfer wires one at a time and ensure tight, insulated connections; don't let wires retract into the cavity
• After reassembly, run a brief bake test to verify operation and clear any residual smoke from first heat-up

This bake element is the oven heating element that provides the heat for baking and roasting. Replace a damaged or failed element to restore normal bake performance and even cooking results. What it does:

• Converts electrical power into radiant heat for the oven bake cycle.
• Heats and glows when operating; failure can cause little or no bake heat.
• Common symptoms: oven won't reach set temperature, food cooks unevenly, or element shows visible breaks or heavy corrosion.
• Fits as the direct replacement heating element for the bake function when matched to your model.

• Disconnect power to the appliance at the breaker or fuse box before starting any work.
• Allow the oven to cool completely and wear gloves to protect hands from sharp edges.
• Confirm terminal orientation and secure electrical connections; ensure the element is seated and fastened per your model's instructions.

This is the large surface heating unit for an electric range or cooktop. Replacing a failing unit restores consistent stovetop heat so cookware warms predictably and meals cook evenly.

• Provides the heat source for the large burner position on an electric cooktop
• Converts electrical energy into controlled cooking heat
• Replace if the burner won't heat, heats intermittently or unevenly, or shows visible breaks, blistering, or burn spots
• Loose, pitted, or discolored terminals can also indicate the unit is failing

• Disconnect power to the appliance before servicing and allow all components to cool completely
• If your model uses plug-in coils: lift slightly and pull the old unit straight out of the receptacle; align and push the new unit straight in until fully seated
• Inspect the burner receptacle for heat damage before reassembly
• Restore power and test operation on low and high settings

The Bake Element is an OEM part for Whirlpool ranges. As a heating component, this bake element is responsible for providing bottom heat during baking and roasting functions.

Causes of a bad bake element include deterioration of insulated coils and connections from continual heat cycling. Exposure to drips or spatters can damage their integrity over time.

Symptoms of a bad bake element include:

• Inability to heat up to desired cooking temperatures
• Slow or ineffective baking and roasting results
• Error codes or failure alarms from the control board
• Visible burnouts or breaks in the coil filaments

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This replacement bake element provides the heat for your oven's Bake cycle. Install a new element to restore fast preheating and consistent temperatures when the original has failed, cracked, or degraded.

• Generates radiant heat during Bake to reach and maintain the set temperature
• Common fixes for: no heat in Bake mode, very long preheat times, or uneven baking
• Replace if the element shows blistering, breaks, or burned spots
• Helps restore proper baking and roasting performance

• Disconnect power to the range before servicing and allow the oven to cool completely
• Remove racks and the oven bottom or shield, take out element screws, and gently pull the element forward
• Transfer wires one at a time and avoid letting wires slip back into the cabinet insulation
• Inspect terminals/wiring for heat damage; do not overtighten mounting screws

This part is a grill element that is used on a cooktop. The element is responsible for supplying heat to the cooking area of the cooktop. If the element is not lighting up orange or red when it is turned on, it will need to be replaced. This part may need to be replaced over time due to normal wear and tear on the appliance. Some users may also notice that the element is not heating evenly or works intermittently. If this is the case, this is a genuine OEM replacement part that is made out of high-quality materials. Unplug the range from the electrical outlet and allow the cooktop ample time to cool down before trying to replace it. Wear work gloves for safety during this process.This part is compatible with cooktops that are manufactured by Jenn-Air and Maytag. It is sold individually and comes from the manufacturer.

This surface element is the electric heating source for one cooktop burner. Replacing a failed element restores fast, even heat and dependable temperature control on your electric range or cooktop.

• Supplies heat to the selected surface burner when power is applied
• Restores consistent heating and proper cycling after element failure
• Common symptoms: burner won't heat, heats intermittently, or shows visible damage/hot spots
• Often tests open with a meter when failed

• Disconnect power at the breaker before servicing; allow the unit to cool completely
• Protect the cooktop surface; follow your service manual for access to the element
• Note wire positions; transfer wires to the same terminals and reuse existing mounting hardware
• Handle by the frame only; avoid touching the element surface. Reassemble and test operation

This radiant surface heating element restores proper burner performance on electric glass cooktops/ranges. It replaces a failed element so cookware heats evenly and reliably beneath the ceramic glass. What it does:

• Converts electrical energy into radiant heat under the glass-ceramic surface
• Replaces a burner that won't heat at all
• Helps resolve uneven heating or only part of the ring glowing
• Addresses visible damage such as hot spots, discoloration, or breaks in the element

• One surface element

• Disconnect power at the breaker before servicing; allow the cooktop to cool completely
• Lift and support the cooktop; handle the element carefully—it is fragile
• Note wire locations and move them one at a time to the new element; ensure terminals are fully seated
• Reinstall mounting clips/brackets so the element sits flat and clear of the glass before restoring power